vortex crossfire ii throw lever 3d models

Throw Lever redesigned for the Sig Sauer Sierra 3 BDX 4.5-14x scope. I've tested it on alternative scopes, but unfortunately, I don't have access to the 3-9 or 6-20x models, so I'm unsure if it will fit perfectly. However, based on its design, it's...

I wanted a larger throw lever than what was available on my CVLIFE Scopes(https://a.co/d/29N7bz1). Let's the gun go into my cases. Uses M3 x 12mm Screw and nut. ... Added V2 which is thinner and more rounded for lower profile scopes.

Decided to Design my own throw lever rather than pay $30 and get one that only hopefully works. Uses an M2 nut which is inserted with the printer paused and a 12mm M2 hex socket cap screw. Can only guarantee it will fit on the specific model listed...

It makes zooming IN/OUT much easier (even in gloves) :)Uploaded model (both versions) has these parameters:inner diameter: 46,0 mmI use this throw lever on my rifle scope Vector Optics Matiz 3-9x/50mm but it can be used for any other.If you need to...

Throw Leveler for VORTEX VIPER PST 5-25X50 For Personal Use Only!

Red Dot Vortex Crossfire Aimlight Blast

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/hh6whwdCUaL

Reflection hider endcap for the Vortex Crossfire Red Dot (Gen 1 & 2). This acts a bit as a sunshade and also gets rid of that bright ruby signature via a honeycomb structure. ... Similar to other anti-reflection endcaps.

Athlon Scope Throw Lever for the Argos 6-24x50 scope.

Throw lever to fit the Bushnell Elite 4500 scope. ... Print on it's side without any support.

This is a simple throw lever for the Monstrum G3 6-24 Scope. ... All you will need is m3 bolt and nut to install it.

This zoom throw lever fits perfectly on the Athlon Ares ETR 4.5-30x56 rifle scope, requiring minimal adjustments to ensure a precise fit. It is compatible with M3 thread inserts measuring 4 mm x 5 mm. ... Printed successfully from both PLA and ABS...

This is a throw lever for the Athlon Talos BTR 1-4X24 rifle scope. ...It slides over the magnification ring and uses an M4 Screw and bolt to tighten it onto the scope.

Throw lever designed to fit Leupold VX-3 and VX-iiiL scopes, however it most likely fits other Leupold scopes as well (scopes with a ≈ 37.7 mm zoom ring and the gas inlet notch). At full magnification, the throw lever has good clearance for both the...

A throw lever designed for the Athlon Ares BTR Gen 1 scope. ...It should also fit the Ares ETR Gen 1 and the Midas Tac, although I have not tested that.Hardware required:1 M3x10 screw1 M3 nutCategory: Sport & Outdoors

Roue de réglage de parallaxe + levier de grossissement pour lunette vector optics continental (5-30x56). ...À monter en force. Parallax adjusment wheel + throw lever for vector optics continental scope (5-30x56). ...Interference fit.

... SLX brakes I bought a set of Shimano Deore 6100 hydraulic brakes. ...Everything worked but I needed an allan key to adjust the throw on the lever. ...After a quick design on Onshape CAD software it was set to glue into the lever and start using it.

Vortex delivers another fantastic red dot sight that's perfect for any rifle or SMG. This small, charming design packs a punch, making it an ideal addition to your arsenal. The model comes fully loaded with game-ready PBR textures and separate...

This is a throw lever designed for the Athlon Ares BTR Gen 1 scope. It should also fit the Ares ETR Gen 1 and the Midas Tac REVIII, although I have not tested that. ...   Requires 1 M3x10 screw and 1 M3 nut.

I'm trying out the magnification throw lever that fits my Sig Tango 6 4-24x50 scope. I'm not sure if this will fit other SIG scopes in the tango line or their other models, so I'd appreciate feedback from anyone who tries it on different SIG scope...

This remix draws inspiration from miprotera's 'Bushnell 1x-4x Quick Adjustment Throw Lever', which can be found here: https://www.thingiverse.com/thing:2566788 The changes made include: Thickness is boosted by 0.3mm to enhance durability. Sides are...

Re-mix from the throw lever by jitblass. I fixed the messed up geometry, beveled the edges (so you don't have to sand them afterwards), and shrunk the cutout for the nut to accept standard M3 nuts. Once printed, you'll need a M3 x 10 screw and...

Throw lever for Primary Arms 1-6x SFP scopes. This is an original design. **TABLE OF CONTENTS** - Parts - Printing Details **PARTS** - (1) M3x12mm socket head screw - (1) M3 nut **PRINTING DETAILS** - Settings (Tested on ender...

The Cat Tail Lever attachment is designed to complement the Optisan Mamba 1-4x scope, which had a limited release a couple of years back. ...This custom component was 3D printed without any support structures.

Simple scope cap for my Vortex HD II

Primary Arms Scope Throw LeverSLx6 Silver Series 1-6"Beefy" to last awhileRecommend course screw of appropriate size and length.Starter hole provided, Predrill hole to avoid cracking.Will clear mid height scope rings in higher. ... Probably won't work...

This lever is specifically crafted for the Athlon Ares BTR Gen 1 scope. It should also be compatible with the Ares ETR Gen 1 and the Midas Tac REVIII, though I haven't tested it on those models yet. Required hardware includes: 1. An M3x10 screw 2.

... stiffer. ...When loading magazines with match ammo that is very greasy it makes turning the know almost impossible. SO I designed a Throw leaver to make it much easier to turn. ... It just requires 1 - 3M x 16mm socket head cap screw and 3mm Nut

It's best to test the lever's fit by scaling up or down after printing at a lower resolution initially. Relying on rafts may not be necessary on most printers, but I used them to avoid an elephant's foot on the base layer. ...Scale everything in the...

A handheld trigger created to complement a Nikon Monarch Riflescope, tailored precisely for the 5-20x42mm variant.