volantex ranger 2400 3d models

Human: Custom twin motor mount for the Volantex Mini Ranger 757-4. Once printed, carefully cut the hinge to disconnect the two separate components. Printing with PLA material using a moderate infill setting of 75-100% and a precise layer thickness...

Replace part of the ruder for Volantex 757-4

FPV Deck for Volantex gliders (Ranger 1600/2000 and Phoenix 2000 V2) The project is a remix of the cockpit base from "Gimbal for Ranger2000" with "Storm32 NT" by Herre Vermeer: https://www.thingiverse.com/thing:4612187 My FPV Deck version has an...

This is a replacement for the plastic piece that connects the two sides of the elevator on the Volantex Ranger Ex/Quanum Observer. The originals have either broken or pulled away from the foam, resulting in wildly unpredictable flights. This new one...

I have a Volantex Ranger 1400 and despite its great price, it has some design flaws that need fixing. Fortunately, the fix is relatively simple: check out Andrew Newton's video at https://www.youtube.com/watch?v=BRojC8QzyPY. One major issue with...

################################# Volantex Ranger 2000 Kit for FP and long range. I had to do these pieces because the Ranger has little space for the big batteries and you don't have room to move them behind to balance the plane. The FC plate is...

replacement internal top deck for the ranger 2000 or 1600. ... brings the FC forward a little so access is better.

Mount the micro Ublox M8N GPS unit to your Ranger or any surface that provides sufficient area for installation. ...For more information, visit https://www.readymaderc.com/products/details/rmrc-mini-gps or...

This is a bridge to be installed in the battery compartment, thus facilitating the installation of the OSD and other electronic components.

This is an attachment system for mounting motors to the wings of a Volantex Ranger 2000 remote control aircraft. ...Twin Engine Volantex Ranger 2000 RC Plane Build - Pusher to Tractor Conversion https://www.youtube.com/watch?v=Psh2D7V-0ug

This is a bracket I fabricated to fortify the engine mount on my Volantex Ranger EX 757-3 (Quanum Observer).

Inner and outer plates to mount 35 mm Leopard motors in the Volantex Phoenix 2400. Loosen the motor grub screw, remove the C-clip, and use a drill-press etc to push the shaft to the other end of the motor, then replace the C clip in the new position...

Support is now available for the FC type F411 WSE and GPS BN220 within the Volantex Ranger G2 system, providing a seamless integration that fits like a glove.

Mount for Beitian BN-220 GPS for Volantex Ranger tail boom. Place gps module with wire plug pointing to the tail to prevent accident detaching. ...

I replaced the standard motor with twin motors on the wings. This design covers the hole where the original motor goes. ... My real motivation is that I wanted to mount a strobe light, so I designed this piece so I could customise it to fit a light.

<p>This wall mount doesn't hold it whole - the plane has to be nose down on the floor.<br/> Snap the tail in, glue it to the wall, when glue sets in pull the tail out.</p> <h3>Print instructions</h3><h3>Category: R/C Vehicles Summary</h3> <p>This...

Print 15% cubic infill, horizontal, no supports! ... https://youtu.be/VD89-zbefyI https://www.thingiverse.com/thing:5090705 https://www.thingiverse.com/thing:4759659

The wall mount isn't secure enough - the plane needs to rest nose-first on the ground. To assemble it correctly, snap the tail section into place and attach it firmly to the wall with glue. ...Once the glue has dried completely, carefully pull the tail...

Fixed the problems in the original scan from markplatvoet with Meshlab. The stl should be printable now in one piece, but needs lots of support. So I used OpenSCAD to split the canopy in half. Added three holes for small screws. The screws should...

Enjoy!

I use ABS and 2mm carbon rod for connection.The photo shows a modified version for my PAN TILT. ...The project has the standard version, as in the render.

This compact platform is engineered to offer a secure surface for installing a VAS bluebeam 1.3 GHz antenna on the rear tail boom of a Volantex Ranger 2000 aircraft.\r\n\r\nThe platform features precision-cut notches that are ideal for securing with...

Replacement tray for your Volantex Ranger 2000. It is stronger than the original wooden tray, I break mine on my 3rd landing lol. I highly recommend you to replace your top tray with this one with a built-in mounting hole for 25mm up to 30mm flight...

For anyone who has broken the internal wing clip on their Volantex V757-6 V757 6 Ranger G2 1200mm. I could not find a replacement the correct size so took the original out and recreated it in Fusion 360 (first time I ever used a 3d programme too). I...

Made specifically for Volantex Ranger EX 757-3. However, it could potentially work with other models as well. Sources are available in Fusion 360 format for anyone who wants to modify the design. Protective glass was cut from a plastic Pepsi bottle...

Few reasons why I built this custom quadcopter\n- raised the deck height to accommodate 4S lipo instead of 3S, resulting in a much more exciting climb rate\n- strategically positioned the Omnibus F4 Pro for optimal mounting with holes spaced at...

Parts list: Ranger G2 PNP - https://www.banggood.com/Volantex-RC-V757-6-V757-6-Ranger-G2-880mm-Wingspan-EPO-FPV-RCAirplane-Aircraft-PNP-p-1133817.html?p=DG23031123036201501P Omnibus F4 Pro FC - https://www.akktek.com/f4-support-sd-card.html?acc=6123...

The Platform Under the Battery and Beacon for Volantex Ranger EX 757-3. Designed Specifically for a Battery Assembled from Sixteen 18650 Li-ion Cells (4S4P). This removable battery is fixed in place with latches, which are only available for...

Remixed for matek 743 wing v3, matek gnss M10-5883

This is a custom motor mount designed specifically for Sunnysky x3120, although i guess it will also fit any other sunnysky motor. This is intended to be used with stock metal plate & screws so you dont need to drill anything. Note that this is a...