volantex ranger 2000 3d models

Various bits I used for my quadplane conversion using 15mm and 10mm carbon fibre tubing. You can see it flying here: https://youtu.be/5N_bSbBPEIo The bolt holes are made for M3 bolts. ... You can use these mounts (for 15mm round tubing) for the...

I soar through the skies over heathland landscapes, where rugged terrain poses a significant challenge for landing. The ground beneath me is a vast expanse of long grass and sparse vegetation, making it difficult to deploy my undercarriage fully. It...

Nylon https://www.youtube.com/watch?v=CAZg3AkOfI8 I utilize a 4-in-1 ESC and two Avenger motors. ...It perfectly fits the Matek F411, either with a 24x24mm mount or a 30x30mm mount.

Replacement cockpit for RC plane volantes G2 1200mm

This is two-part mount. The tail part is glued to the plane and the camera part is pushed in. ... This mount is for cheap [Kingkong camera from...

I'm not a fan of the huge landing gear and wheels that the plane comes with. The placement on the fuselage is too far back and the wheels are ridiculously big. I do like the small center wheel however it makes it hard to take off on a narrow runway...

Crashed my bike and snapped my tail off - no way could I find that pricey part anywhere, so I took matters into my own hands and made one myself.

This is a replacement part for the center console of a ford ranger. Print Settings Printer Brand: Creality Printer: Ender 3 Pro Rafts: No Supports: Yes Notes: This print works well as a quick replacement, If you live in a place where it gets very...

Simple tray for mounting Raspberry Pi Zero. ...Lets you attach board with zip ties, rubber band or by melting the pins. In my case hold a board used for OpenHD under Volantex Ranger 2000 canopy, mounted over camera pan servo.

This is a replacement for the bracket that holds the horizontal and vertical stabilisers onto the tail of the old version of the Volantex Phoenix 2000 742-3 (not the V2). This part is prone to break where the legs meet the main body of the bracket,...

Designed specifically for the Volantex Ranger EX 757-3 aircraft, this product offers versatility and convenience. Each wing is equipped with a four-pin RC Servo connector that allows you to connect the ailerons, flaps, and headlight securely. After...

Replacement skid for wheel if you need to remove the wheel and cowl to attain CG. ... Use M3 screws to bolt together.

I carefully printed my model with a 100% infill density to ensure maximum stability and strength. Next, I utilized the two original screws as intended, providing a secure anchor point for the assembly. ...Finally, I reinforced the connection by applying...

Hi, please use my project where we can hang wings on the wall. ... I hope you like it.

This Mount is specifically designed for securing a GPS unit on the curved exterior surface of an aircraft. The top of the fuselage has a rounded shape, which makes it impossible to stick the GPS unit directly onto it. To address this issue, I created...

Motor mount: I ended up using the 10degree-motor-p2.stl, that give the best result when you mount it in a way that point the motor more to the sky.GPS mount is for M10Q-5883Skids wheigt is 80g incl 7cm wheels

Printed mine using ABS as it gets quite hot at our flying field. ... needs supports.

Printed in petg and TPU. need to remove original rudder support and glue the new one. First glue two M3 nuts in new rudder support.Then sharpness is needed when drilling the fuselage (3mm hole). you'll need to measure and cut an M3 threaded rod...

Cameramount for Micro-Cam, specifically a Foxeer model that I've chosen. ...I'm able to secure it in place on the nose section using double-sided tape, which is often referred to as "foamy".

I broke triangle end of original wing clip and glue this part to the rest of clip. Tested - works ok. ...Easier than replacing of the whole clip.

Verification status pending, awaiting technical validation of AI model functionality.

I needed a better locking mechanism than the one that came with the foam, so I built this small project. Main feature: - It can be used without glue by simply fitting together tightly. - For added security, you can also attach it using glue. - The...

<p>Simple tray for mounting Raspberry Pi Zero. ...Lets you attach board with zip ties, rubber band or by melting the pins. In my case hold a board used for OpenHD under Volantex Ranger 2000 canopy, mounted over camera pan servo.

This is my first revision to mount the Speedybee F405 Wing FC.The FC sits a bit lower on my design to prevent the wing rod from hitting the cables.I will soon add a mount for the GPS and maybe add quick connectors for the wings.

<p>This motor mount was created to be easy to print and mount. After printing, scratch the outer 1mm of the print, apply hot glue and stick in the nose of the aircraft.</p><p>It has been tested with the t-motor 2814 and 2820 motors. ...make sure to...

This plate secures the wings to the fuselage by covering them and keeping them firmly in place. To strengthen it, I've made a few modifications since 3D printing will produce a weaker component than the original. For camera mounting purposes, I've...

This upper deck is engineered to streamline and optimize the installation process for key components such as the steering wheel, while also providing dedicated spaces for the PSU, Controller, GPS, DragonLink, and EzUHF. ...The design allows for seamless...

Front bottom camera mount for Foxeer Razer. Mount has a hole for weld in M3 nut. Put camera in to the mount, set it in the place at the correct distance, mark point for the screw hole, drill 3mm hole, bolt the mount and voilá. ... STEP file...

This is a critical component that securely attaches the wings to the fuselage. To enhance its durability, I have revised the design with reinforcements in mind, considering the inherent weakness of 3D printed parts compared to their original...

My plane has detachable wings so I didn't want to make a fixed mounting for the antenna. So did these clips for antenna and it's wire. The antenna clip file provided is for the right side. Mirror it in the slicer for the left side. Print in...