volantex ranger 2000 3d models

Volantex Ranger 2000 Canopy After putting in a lot of effort, I've managed to get a near-perfect fit for the canopy. You're welcome to use it however you like. The intention behind sharing this design is to enable other creators to build something...

Wing clip lock for Volantex Ranger 2000 (and maybe even 1600 and 2400). ... I use it with https://www.thingiverse.com/thing:2733056

This is a replacement motor mount for a Volantex Ranger 2000 glider. The original mount cracks easily due to crash, vibration, or over-tightening. ...

Here are a few parts I am using on my Volantex Ranger 2000 build. I crashed on the second maiden and broke the plastic piece that holds the tail feathers on. I have made parts for that too. ... Details on an upcoming video on my YT channel: ...

I wanted to put a pixracer flight controller in my Volantex Ranger 2000, but the original wooden tray wouldn't accept the 30.5mm square mounting holes. I decided to create a new tray that would replace the old one and allow me to mount the pixracer...

################################# Volantex Ranger 2000 Kit for FP and long range. I had to do these pieces because the Ranger has little space for the big batteries and you don't have room to move them behind to balance the plane. The FC plate is...

These are some parts i made to get crossfire, GPS and FPV on my Ranger 2000. ...I placed the FPV camera on the tail, the position in the nose i found too low, the lens probably needs to be cleaned after each landing.

Volantex Ranger 2000 Hobbywing Flyfun 40A ESC mount. ESC fixed by rubber ring from bicycle tube or nylon tie. ...See the pics and have a fun :)

Volantex Ranger 2000 camera mounting platform. allows you to replace the battery without moving the video transmitter or camera. for the hinge I used a 3mm carbon rod. for the door lock spring I used a pen spring. all the pla parts were glued...

This is a remix based on the fc_tray SCAD-file. ... Added some comments, two mount positions for fc, some openings for cables an ties, corrected the front width for Volantex Ranger 2000. ... Thanks to harindrawisnu for the original SCAD sourcecode.

Replacement Clip for Volantex Ranger 2000 wing attachment available. Suitable for various models, though unique compatibility with Ranger 2000 unknown. Fits identically to stock clip and securely holds wings in place with impressive strength. ABS...

################################# Volantex Ranger 2000 Kit for FP and long range. I had to do these pieces because the Ranger has little space for the big batteries and you don't have room to move them behind to balance the plane. The FC plate is...

I use ABS and 2mm carbon rod for connection.The photo shows a modified version for my PAN TILT. ...The project has the standard version, as in the render.

Fixed the problems in the original scan from markplatvoet with Meshlab. The stl should be printable now in one piece, but needs lots of support. So I used OpenSCAD to split the canopy in half. Added three holes for small screws. The screws should...

This is an attachment system for mounting motors to the wings of a Volantex Ranger 2000 remote control aircraft. ...Twin Engine Volantex Ranger 2000 RC Plane Build - Pusher to Tractor Conversion https://www.youtube.com/watch?v=Psh2D7V-0ug

replacement internal top deck for the ranger 2000 or 1600. ... brings the FC forward a little so access is better.

This compact platform is engineered to offer a secure surface for installing a VAS bluebeam 1.3 GHz antenna on the rear tail boom of a Volantex Ranger 2000 aircraft.\r\n\r\nThe platform features precision-cut notches that are ideal for securing with...

Replacement tray for your Volantex Ranger 2000. It is stronger than the original wooden tray, I break mine on my 3rd landing lol. I highly recommend you to replace your top tray with this one with a built-in mounting hole for 25mm up to 30mm flight...

If yours hook broke, just 3D print that I have mine working for one year now, printed with PLA

A sleek new battery tray features a distinctive design element - a mounting surface for a high-resolution board camera.

XM+ mount for the Volantex Ranger 1600/2000. I attached the antennas with zip-ties and skewers and I screwed the cover. Be sure to screw it so you have access to the bind button. ... The support was designed to fit as much as possible behind the motor.

This is the wing fixing part located in the fuselage. ...Depending on the printer and settings, the holes may need some drilling to 1.5mm diameter.

The human mounts a pan and tilt setup using a pre-existing mounting point located on the nose canopy cover. This static mount allows for smooth operation of the camera system. ...In addition, the standard velcro straps used for attaching action cameras...

FPV Deck for Volantex gliders (Ranger 1600/2000 and Phoenix 2000 V2) The project is a remix of the cockpit base from "Gimbal for Ranger2000" with "Storm32 NT" by Herre Vermeer: https://www.thingiverse.com/thing:4612187 My FPV Deck version has an...

XM+ mount, I attached the antennas with zip-ties and skewers that I fixed on the two little things behind. ... Feel free to ask if you need the SLDPRT files ;)

A replacement battery mount that lowers the battery about 20mm. ... You may need to print with a small amount of support under the first few battery strap holes as they have some relief for the battery strap.

A stable modified motorplate for this beautiful RC airplane. - 1.2° side-tilt (near original) - 2.0° less up-tilt I experienced a relatively strong up-pitch powering up my Sunnysky X2216-III motor so I create this plate to give the thrust 2°...

This is a remix of @nick9one1 battery tray. Extended the back, split it up into 3 sections so it's printable on smaller beds. It's a work in progress, so there might be some issues. I'll update the files if there are changes. ...

... ...For more convenient printing, the two parts can be joined together using glue. UPDATE 2019-09-28: Tail support has been added for Volantex Ranger 1600. ...Additionally, a clip for standard crossfire boxes and photos of the Ranger 1600 are included.

Wing clips for Volantex's Phoenix lineup. ...Printed with PLA, and works good.