vivedino 3d models

Replacement parts, Upgrade parts for the Vivedino Troodon 3D Printer 300mm model but some parts should work on the bigger model. ... Check out my videos about printer and the parts; https://www.youtube.com/watch?v=0rVzCr6NkjU ...

Just a basic power switch bracket. ... Used to reposition the power switch on the side of the Vivedino Troodon instead of having it on the back of the printer which is a pain considering the size of the printer.

Designed a filamentguide for my Formbot/Vivedino T-Rex printer. The mounting is very easy, just unscrew the screws from the bearings and place the guide between the bold and the frame. Sometimes i had the problem that the spool unrolls to much...

I'm attaching a spooler holder specifically crafted for my Vivedino T-Rex 3.0 model. This design is engineered to seamlessly integrate with any standard 40x40 aluminum profile, ensuring compatibility across the entire range of T-Rex models. No screws...

Alignment brackets for the Vivedino Troodon 400 flex plate. Slide the plate in until it touches the rear brackets, then lay the front flat. Notes - Only longer rear brackets are needed. - If using front brackets you will have to calculate your...

A Mounting Solution for the Vivedino Raptor 2.0 (Step File Included) Two mounting configurations are available for the Hemera, with the second setup specifically designed for a volcano-style build. This mount is offered in two versions, each...

Side brackets to hold Berd-Air Cooling Pipes on the carriage of the Vivedino Troodon 400. These attach with the mount locations for the stock shroud. Please note the notches to go around the gantry belts, and the cut screw tab to bypass the...

I made this to adapt a ViveDino Duet board LCD to BigTreeTech tft35 LCD YouTube Channel https://www.youtube.com/channel/UCZ8WG-kqF1kmL2s0xIMfIIg If you found this video helpful or would like help fund future experiments.please donate below. ... Patreon ...

This direct fit replacement is designed for your Formbot/Vivedino Raptor/Raptor 2.0 extruder arm and should also work with gCreate Gmax, Gmax 1.5, Xinkebot Orca 2's, etc. It takes only 3-5 minutes to swap out and requires no additional parts. This...

0X/0Y/2019: Version 1 The adjustable 40x40 fan mount is designed for the Vivedino Formbot Raptor 2.0, but it's also compatible with other printers that use an E3DV6 Hotend. The original stock fan duct design had a major flaw - it would inevitably...

I had issues with cable chain sag so I modeled this up to fix the sagging cable from snagging the X endstop mount.

I was having issues with my extruder tension gear was hitting the extruder cable chain. Here is my mod to fix it. ...

I made this spacer to keep the cable chain tensioned while gantry is moving. ...keeps everything nice and tight.

This 120mm fan runs silently on 24V despite being designed for a 12V power supply. ...Check out this Amazon product: https://www.amazon.com/gp/product/B00ECWKD6I/ref=ppx_yo_dt_b_asin_title_o09_s00?ie=UTF8&psc=1 or this one:...

Vivadino Raptor 2.0 Duct Fan - Perfect for Cooling and Ventilation Systems PETG or ABS Materials Available

This is an adjustable wipe bar to clean filament from the nozzle. This is attached to the Y-axis extrusion and will go up and down with the gantry, which can allow for custom nozzle wipe code to be inserted in files (I have not done this). Note -...

Designed this for my Troodon, I had upgraded it originally to the Orbiter 1.0 but was unhappy it got rid of the Bowden Tube which supported the filament from being stressed. The new Orbiter 2.0 added the Bowden tube connection but the mounting screw...

ENG I created this brake for avoid the Z fall down with propry weight. I inserted a 2,5mm felt pad (like as for chairs legs) and glued with the brake. ITA Ho creato questo freno per evitare che l'asse Z scenda con il proprio peso. ...Ho inserito un...

This is just a general fan shroud I made for the Formbot Raptor 2. The one it came with was very low powered. This allows for a lot more airflow but its just a generalized flow over the part. I printed mine in PLA since its not close to the nozzle...

ENG I created this brake for avoid the Z fall down with propry weight. I inserted a 2,5mm felt pad (like as for chairs legs) and glued with the brake. ITA Ho creato questo freno per evitare che l'asse Z scenda con il proprio peso. ... Ho inserito...

I became increasingly annoyed with the Forbot/Vivedino Raptor 2's stock spool holder requiring frequent adjustments for varying spool sizes of filament. With a few minutes in Fusion360 and some quick revisions, I designed a set of rollers that fit...

I had some problems with the extruder and hotend of my T-Rex printer so i decided to change to a BMG Extruder and an Dragon Hotend. For assembling, you need to take of the "old" print head. I replaced a spacer from the carriage to hold the motor...

This carriage mount relies heavily on stock parts. To complete it, you'll require a V6 clip-on fan mount and a threaded heat sink. ...By incorporating the threaded heat sink, you can expect enhanced stability in your hotend assembly and significantly...

I was at a point where I was disassembling the hotend on the Troodon pretty frequently, and didn't like having to undo so many screws when I did it. This hotend bracket uses one 30mm fan and the 2 stock 4010 blower fans. ... The duct has been...

designed this for a customers troodon klipper conversion Favorite Filament https://amzn.to/46aFjI1 If you found this video helpful or would like help fund future experiments. Please donate below. ... Patreon ...

This is designed to replace the stock hot end mount for an E3D V6 hotend directly. The stock hot end included with the T Rex 3.0 cannot handle temperatures above 250 degrees, resulting in PTFE tube breakdown and jamming issues. While a metal heat...

This is a straightforward upgrade package designed to seamlessly integrate with the Bondtech BMG and Dragon hotend. 1. Swap out the top two motor screws securing the PCB's with longer 35 mm M3 bolts for added stability, reusing the stock mount...

These STL files cover every 3D printed component for our Vivedino T-Rex 3.0 printers, sourced directly from the manufacturer. ...Hopefully, they will be just as beneficial to others who have been in my shoes.

These are all of the STL Files for any 3D printed part for our Formbot (apparently now called Vivedino) T-Rex 3.0 printers. I got these directly from the manufacturer. ...Hope this helps anyone like it did me!</p> Category: 3D Printer Parts

Formbot/Vivedino Troodon cable can sag and begin x shifting in certain places because the cable doesnt make it all the way up to the ledge of the limiter. This lowers the rake of the part and prevents that sag from causing layer shift. ... Update...