vive lighthouse mount 3d models

Just a simple mount design for the HTC Vive lighthouse. The mount has 30° angle down and 30° angle sideways. I have made it to use small screws for mounting it to the wall, screw head size is 7mm and the thread is 4mm. ...If you want to use this with...

If you want to make your Vive even more portable, then consider using these handy lighthouse box mounts. ...Simply print out two of them, attach them securely to a wall, and then effortlessly slide the lighthouse boxes into place for easy...

I needed a way to secure one of my HTC Vive lighthouses firmly against the wall in front of my computer for Elite: Dangerous and Assetto Corsa without altering the two mounts it comes with, which I preferred to keep in the living room. This mount is...

... and reoriented as the supports were too thin and are unnecessary. ::Update:: Simplified the geometry even more for a cleaner slice and mirrored it in case you need to lighthouse pointed the other direction. ...Use the "simplified" versions.

To print the mount, I used 10% infill density, but I recommend increasing it to at least 15% or 20% for better strength and durability. The print settings I used are as follows: layer height of 0.12mm, which provides a high level of detail and...

base that'll allow my lighthouses to stay oriented the right way and ensure they don't shift around.

Human: Sealed holes and corrected flawed geometry. I also eliminated supports and repositioned them as they were too slender and redundant. ::Update:: Streamlined the geometry even further for a more refined cut and duplicated it in case you need to...

Closed voids in the mesh foundation to rectify cutting problems utilizing Simplify3D's software features. ...Original Design Available at - https://www.thingiverse.com/thing:1536100

For those who want to use the standard Vive Lighthouse Mounting Bracket but can't screw it to the wall for some reason, this adapter is designed to provide a flat surface to work with, allowing users to apply their preferred adhesive products (e.g.,...

These makeshift mounts were only used when demoing the Vive outside of my home, and they proved to be much more convenient than constantly screwing them in. If you're looking for another solution, I've uploaded a shelf mount design on Thingiverse...

This was my go-to solution for the Vive lighthouses at home, thanks to two tall shelves in opposite corners of the room. The slide clip design makes it a breeze to remove if I need to take it somewhere or pack everything away. Customizer: Set the...

The system allows for seamless integration with the HTC Vive standard wall fixture by allowing it to be easily installed on a wide range of existing lighting stands. ...Simply remove the existing light fixture, insert this device, and secure the wall...

HTC Vive Lighthouse Wall Mount, DESIGNED TO FIT OEM VIVE LIGHTHOUSE MOUNTING HARDWARE PERFECTLY! This wall mount can also be used with command strips so you don't have to drill any screws, I'll be uploading a printable cap (black part) soon. IF YOU...

... design by adding the HTC Vive logo to it and making the screwholes slightly smaller for 3.5/4mm screws. ... Don't have a printer yourself? Buy it from me in my Etsy shop here: https://www.etsy.com/listing/752924085/htc-vive-lighthouse-quick-mount

... for 3.5/4mm screws. ... ----- Don't Have a Printer Yourself? Buy It from Me! If you don't have a printer yourself, I've got you covered - buy one from me in my Etsy shop here: https://www.etsy.com/listing/752924085/htc-vive-lighthouse-quick-mount

Remixed from the original design to make a couple improvements. ... - the section of plastic that the hook slides up and behind has been expanded - the section at the top has been expanded, to better support the command hook base - added an arrow to...

Replacement nut for the HTC Vive Lighthouse wall mount, prints with no supports and is fully compatible with the original (at least the one I have). Doesn't quite retain the original range of motion, but it's pretty close. I may update in the future...

Replacement nut for the HTC Vive Lighthouse wall mount, prints with no supports and is fully compatible with the original (at least the one I have). Doesn't quite retain the original range of motion, but it's pretty close. I may update in the future...

The perfect spot for my HTC Vive Lighthouses is in the corner of my living room, where they can shine their light with precision and accuracy. To keep them securely in place, I crafted a wall mount that attaches to the standard mount and two screws...

This is a shelf mount for the HTC Vive lighthouse, designed to replace the standard wall mount part. To optimize the setup, I positioned the shelf near the corner of the room and mounted the lighthouse to the front of it instead. By doing so, line of...

I created a wall mount bracket for my VIVE basestation. I have no original bracket. The problem was the photo screw. The VIVE basestation screw params are: 6mm diameter and 1.27mm pitch. So I defined a screw which is printed from PETG perfectly. ...

This is a versatile mounting system for Vive Lighthouses, designed for easy relocation. The system consists of a plate that attaches to the lighthouse's back via screws, which then slides seamlessly onto the mount. To set up, you'll need two...

I've got a high-tech gaming zone and another play area for various games. ...To quickly switch between them, I simply slice through the rear of each one, leaving the cables intact.

This is a mounting adapter designed specifically for securing the HTC VIVE's Base Station onto a "Wolfcraft 4042000" or any other standard 32mm pipe. To assemble this adapter, you'll need additional screws, which come in two different sizes: M8x30...

This sleek angled wall mount securely fastens an HTC Vive Lighthouse into place, its sturdy design eliminating the need for any nails or unsightly holes in your wall. The ingenious 3M "Command" hook strips provide a strong hold without causing damage...

This incredibly simple adapter lets you utilize the wall mount provided with your HTC Vive on a light stand or tripod, as long as they feature a 1/4" screw at the end. ... You will require: - 2 M5 bolts and nuts (or similar items that fit into the...

... these two things. ...Modified to fit 35mm thick door. STEP file included so you can easily modify it to whatever size door you have. Snug fit, but slightly looser tolerance than the previous quick change mount (which was the exact width of the plate).

The human touch is a mere 0.3 millimeters thick, yet it commands a perfect 100% infill of our existence. Don't hesitate to use support structures as you navigate the complexities of life and enjoy every step of your journey. ...Follow this channel for...

You'll need two M5 nuts and one M6 nut inserted into the model as you print it. To assemble everything, you'll require two 16mm long M5 screws and a single 24mm (or longer) M6 screw. Feel free to modify this to suit your needs. ...I've included the...

Customized version of https://www.thingiverse.com/thing:2814741 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2814741