vintage computer case 3d models

computer system block 3d model unity ready

simple environment with a computer and some decorations

I was building a NAS system with an old computer and the mainboard only has PWM control for the CPU fan, not for the fans inside the case. So I went for this controller board and needed something to mount it inside the case. The mount is for...

I was building a NAS system with an old computer and the mainboard only has PWM control for the CPU fan, not for the fans inside the case. So I went for this controller board and needed something to mount it inside the case. The mount is for...

Its primary purpose is for CPU mining but It can also be a self contained computer case. ...Switch is 12MM https://www.youtube.com/watch?v=rv33KaoPK6c Similar Switch on Amazon ...

Its primary purpose is for CPU mining but It can also be a self contained computer case. ...Switch is 12MM https://www.youtube.com/watch?v=rv33KaoPK6c Similar Switch on Amazon ...

Suitable for any computer case with a full height 5.25" drive bay.My Antec P90 case is huge, but actually barely fits my GTX 1080 graphics card. Closing the side panel effectively cuts the lower case fans off from the CPU cooler. This fan duct...

... It wasn't intended to be your only computer but to replace your more valuable computer when participating in fieldwork. In the past year, the single-board computer landscape has changed, with new systems running on tiny, powerful 64-bit ARM chips.

Practicing my skills in 3D modeling led me to design and build a custom computer desk from scratch.

This extraordinary development not only redefines performance potential but raises fundamental questions about design philosophy - Can PC cases adapt to ever-more-demanding computing tasks? Is air management still a neglected area in need of serious...

I'm working on an old IBM Personal System/2 computer, built around 1987-89 for my electronic project box. After gutting the system, I wanted to reuse the original 120VAC power switch connected to the front panel. To accommodate this, I also created a...

I made this based on a suggestion in the Color Computer Facebook group that it was too easy to find cases shaped like other classic systems and not easy enough to find one shaped like a CoCo. Problem solved. This fits my Raspberry Pi B+. Google...

If you have an old ATX computer case and power supply lying around, why not use it to expand the storage of your main PC? Turn it into a DAS! (Direct-Attached Storage) This design mounts 4 disk racks in the space that would normally be occupied by...

An adapter for a 120 mm fan in the front of the case, taking three 5.25" drive bays. The fan is held in place by four M4 (4 mm) screws, the adapter standard M3 (3 mm) screws, the same 5.25" drives use. I was able to hold it in place with M3 screws...

 I wanted it to have a retro look without copying any actual computer case.  The parts are small enough to print on a Prusa Mini+, but you need to print without skirts or brims.  You also need to be careful with supports to keep them...

A pressure-fitting plug for the Vintage Kenner cases that allows them to be hung on a wall to display. ... If the result is slightly smaller then add electrical tape or print 1% larger.

The elevated stance enhances ventilation within the case when it is adapted for mounting a fan at the base. ...These pedestals accommodate a #6-32 machine screw from above and feature a cavity in the bottom to permit a floor-mounted configuration as...

Use 3mm heat set inserts to attach PCB.attach mount to case with 2 sided tape or similar. Pinouts:5 HDD LED +18 HDD LED -19 PWR LED-20 RST GND21 RST22 PWR23 PWR LED +24 PWR GND Break out board (25P 1mm...

A Raspberry Pi case made as a portable for my radio hobby. It can be held in one hand with the trackbaĺl mouse operated with thumb or index finger (depending on orientation). Openscad file included for customisation. Pi and UPS models also created to...

The adapter is designed for a 120 mm fan at the front of the case, occupying three 5.25" drive bays. The fan itself is secured by four M4 screws that are 4 mm in diameter, while the standard M3 screws that come with it measure 3 mm in length,...

That's the hexagon-shaped screw with a built-in washer, commonly used when mounting PC case panels, floppy drives, hard drives, CD-ROM-drives, and so on. A 6mm depth isn't recommended, yet it's frequently seen in use. I needed a 2mm spacer and...

A few years ago I designed the PocketPi--a simple Raspberry Pi Zero W enclosure--using a demo of Rhino and after that trial version of Rhino expired I redesigned the case using OpenSCAD. This is the latest version of that redesign and the second...

I designed a custom ITX mount that lets you attach the motherboard right on top, while still allowing for some airflow underneath. ...This component is actually a key piece of my DIY costume desk PC build.

Customized version of http://www.thingiverse.com/thing:58001 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=58001

The majority of the script issues have been resolved, with the main problem being the use of all 'center = true' flags which made everything more difficult. Now it is fixed and updated, supporting PSU spot generation (bottom, fliping of PSU screw...

Standoffs for a iBUYPOWER Slate HAKO MR front glass panel to improve airflow to the front fans.

The model was created using OpenSCAD. To assemble, print a cover normally and a fan blade upside down. Attach wires to a motor then glue it onto the cover (motor holders are provided). Next, insert the fan blade onto the motor's mounting screw,...

When I wanted to add a card reader to my desktop PC, a part of the Quick-Release-Clip broke in parts. I tried to make my first 3d model with AutoCAD. There are two versions, one with and one without a grip. ... ...

Vass Sándor féle micro SD kártya olvasóhoz tok. Rev 1 és Rev 2-höz is jó. A Rev 1-en nincsenek furatok így tettem bele 2 fület ami a 2 nagy IC foglaltjában megakad, így nem jön ki a kártya. ...Nem díjnyertes formaterv de funkcionális.

This is a personalized adaptation of the design available at http://www.thingiverse.com/thing:58001, which was created using Thingiverse's Customizer tool (http://www.thingiverse.com/apps/customizer/run?thing_id=58001).