viking longhouse model

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 custom_bottom_port_x_position = 20 custom_bottom_port_corner_resolution = 8 stencil_rotation = 0...

So go ahead and print the firmware appropriate for your printer.icarus-orbiter-2.0-xplus-imate-firmware.gcodeJust place it on your USB stick and print like you would print a normal model. It will make adjustments to the motor directions, X and Y...

I have not tested them personally so if you need assistance, speak to the mod/remix designer. E3D V6 Bowden Mount If you want to use an e3d v6 bowden setup with STEVE, this mod will allow you to attach directly to the stepper motor mount with...

--- ###Running the Customizer Thingiverse hadn't run their customizer queue from Jul 10, 2020 to Aug 4, 2022 and may stop running it at any time again, so if they don't process your customized job, you will have to install and run OpenSCAD (free...

Alexander is depicted here with large eyes with modeled lids, slightly parted lips, and the characteristic creased forehead. His thick leonine hair is swept up at the forehead in with locks breaking to the left and right. Deep drill work is used...

---- ###Running the Customizer### Thingiverse hadn't run their customizer queue from Jul 10, 2020 to Aug 4, 2022 and may stop running it at any time again, so if they don't process your customized job, you will have to install and run OpenSCAD (free...

--- ###Running the Customizer Thingiverse hadn't run their customizer queue from Jul 10, 2020 to Aug 4, 2022 and may stop running it at any time again, so if they don't process your customized job, you will have to install and run OpenSCAD (free...

The enclosure is just pressed together. Barrel Jack Connector eBay Search: 5.5 (2.1,2.5) panel connector The connector was added after I printed my lamp, but you can still see it in the test model. I just used a wire in my lamp, which doesn't look as...

Adjust the bed leveling screw closest to where it measures and by the time the script has looped three times the bed will be perfectly level.Copy to your USB and just print it like you would a normal...

I made another without the holes which may be easier to print, but left the models with the holes for anyone who likes that look. For cable management beyond the arm mount, the following clips work really well for 2020 extrusions: Delta 3D Printer...

9) Wire the power and sensor wires to the Adafruit Proto-Screwshield (Wingshield) using the 'Wiring' section (above) as a reference 10) Connect 5V power to the 2.1mm jack to be sure everything works as expected 11) Attach the front to the rear of...

The hemispheres and cores need to stay close to dimensions of the model for the core to fit just right inside of the hemispheres. A full set is 25 spheres of each color. I would recommend reviewing the sphere assembly process section before printing...

...More importantly, Thingiverse hasn't run their customizer queue since Jul 10, 2020 so until they fix that issue, you will have to install and run OpenSCAD (free software) on your own computer to process the code to create your own customized models.

The box is version 1 and from January 2022 GridAS_gridFirst + second number = grid sizethirth number                = number of elements in the widthfourth number            ...

I also like to print model airplanes, and deltas are easy to make taller. Thus a delta with 350mm diameter bed, and 1 meter towers. Print volume is 350mm diameter by 440mm tall. You can fit a 230x230mm square on the plate and have a bit of room left...

18-48V AC/DC voltage models are available for network systems and marine vessels. We also offer an additional 347-480V high voltage, 125-250V DC, and 0-10V dimmable versions of this explosion proof LED light fixture.Wiring & Plug: This explosion...

If you like my model, just hit '♥'. No payment required; enjoy! 😊</s> <|im_start|> assistant Intelligent tea lights for your apartment's décor prevent finger burns. Appreciate the design? Hit the '♥'. No payment, just fun! 😉</s> <|im_start|>...

The alarm will result in an alarm sound provided by the buzzer modele, the built in LED enlight in RED and the display turning RED. By the built in settings options, the Buzzer can also set into silent mode, where only the LED and the Display are...

18-48V AC/DC voltage models are available for network systems and marine vessels. We also offer an additional 347-480V high voltage, 125-250V DC, and 0-10V dimmable versions of this explosion proof LED light fixture.Wiring &amp; Plug: This explosion...

This post will be full of spoilers, so if you are planning to read the book, read it first. I made this model using Ubuntu available tools, not because of having any advantage, but because I was forced to work on Linux at that time, so I challenged...

I used 20% infill with gyroid pattern, but it doesn't really matter what infill options you choose as only a tiny bit of the model will be affected by that setting. You need to use the correct line thickness of 0.6mm and you'll get a good, quick...

&nbsp;The tire model itself isn't chiral. &nbsp;The tire part is only chiral after printing with one side down, and only appearance-wise. &nbsp;Functionally the tire should still be non-chiral until you attach the tire to the wheel at which point the...

If you are looking for perfection (and quiet printing) put the effort in to hand-fit the integrated bushing version and be amazed at the results.Post-Printing// model: Prusa i3 MK2/3/S/+ Y Chassis Bearing Straps with Integrated Bushings//.// author:...

...More importantly, Thingiverse hasn't run their customizer queue since Jul 10, 2020 so until they fix that issue, you will have to install and run OpenSCAD (free software) on your own computer to process the code to create your own customized models.

You may have to insert a custom hole for a usb lead depending on your mounting position, this could be done in the model, or via a drill after printing. You will need to do some tweaking to keep the led matrix against the grid. This can be via...

The objective is to not create bulky pieces of plastic that distract from the model with the exception of when it is necessary to do so, such as a lift system and a track splitter/track combiner, motor and battery mounts, etc. I will be adding a...

Info on this cooling system can be found here: https://www.prusaprinters.org/prints/62523-delta-p-fan-duct-v2-r2-for-mk3s-extruder To accommodate the widening of the X Gantry, firmware changes are required to reclaim the full 250mm printing width....

I planned to use sensorless homing and didn't need it, so I didn't add it. MiscIf you are wondering where the beautiful Hemera model in the pictures came from, here is a linkPrint SettingsPrinter Brand:AnycubicPrinter:Large Size...

A STEP file with all the final models is posted here, to make remixing easy. I only ask that if you make a change you like, please share your remix so everyone can benefit. I used Hatchbox Wood PLA for the sides and regular PETG for the other...

We don't use the shell.PrintingPrint all models in their original orientations.The faceplate should face down and needs no support. You might want to add a little bit of negative Z offset to this one for a squished first layer on a rough bed for a...