video game controller holder 3d models

There weren't enough space in the original Hercules carriage for a dial indicator holder so I decided to make this separate carriage for a dial indicator.The Hercules carriage is very easy to remove. Just unscrew the parts cooling fan duct from below...

## For use with Smart Filament Sensor - Adapter for HallON v3.stl - Bracket for HallOn v3 stop and Smart Filament Sensor.stl - Stop for HallON v3.stl ## For use without Smart Filament Sensor - Adapter for HallON v3.stl - Bracket for HallOn v3...

This ruled out a traditional battery holder. Instead, I decided to use a stripped length of solid wire to make contact with the batteries. I experimented with putting a CR2xxx coin cell on edge at the base and sliding the wires down the sides, but it...

Keep overall weight to a minimum X and -X endstops Accessible adjustment of the Titan extruder Canted hot end cooling fan (40 mm fan) Mount part cooling fan behind X rails (50 mm x 10 mm blower) Circular distribution of part cooling air Adjustable BL...

2 other holes with M3 thread inside are needed for front-left and rear-right glass holders. Bed plate already has similar holes in 2 other corners (see image). Print 4 copies of corner.stl thing. ABS would be the preferred option. Use 0.2mm...

Remove the paper from the other side, and firmly press the part against the interior wall of the plastic box in the marked locations, making sure that for the brackets, the U shaped rod holder is facing up, and for the passthroughs, that each is...

If you're using the stock everything on the X axis, you can orient the Y carriage plate as it was previously.Using the new M5 bolts, mount the belt holder to the bottom of the carriage plate. Pay attention to the belt alignment, which loops to the...

The open bottom hooks allow for lots of support without adding so much friction that it is impossible to remove the perch holder. SUPPLIES FOR NATURAL BRANCH: no. 4 countersinking screws 3/4 inch long (I used Hillman product 35081) 3/16" wood...

...Anyone may print copies for their own personal use, but selling or otherwise monetizing them is not permitted, and puzzle designers retain all rights as copyright holders of their work.Our puzzles are modeled using the open-source puzzlecad library.

Axle parts: Housing 5mm Bearing holder Housing backing Frame parts: Frame parts are able to rotate to fit together. There is the ability to add 2mm steel rods through out where they join. Length range 40mm to 100mm. 40mm are the holes that line up...

I tested it out and it seems good, but to stop the weight of the cables plugged into the dock pulling it back I used some Command Strips on the bottom of the dock holder to keep it in place. Bill of MaterialsRequired: 3D printer and filament (inb4...

Printing the rollers sideways in halves could be a possible solution for increasing the strength of the thin spindle. The Tray: (Optional) Print the desiccant pack holder, “Drybox Desiccant Tray.stl” (Recommended line width, 0.5mm). You could also...

(if you want to go faster tune the speed up to 130%)All the stls are in the right orientation.The back plate can be laser cutted or 3d printed, all the files are included.Prints the following parts:1x PanelMeterClock_v1_Body: Prusament PETG, Preset...

Print profile is in the attached 3MF file and Gcodes, which are for a CR-10 upgraded with a BTT SKR Mini E3 V1.3 with MicroSwiss DD extruder and dual Z stepper using Klipper. Build instructionsSwitch off and unplug your printer just to be...

Don't do much larger than that. Assembly!There are some order specific details when it comes to assembly.Go ahead and add the m3 nuts for the belt holder screws first. Then screw in the bearing blocks. ...After that, you can put on whatever,...

They each had pros and cons. Spool holders and buffer that came with the MMU2(s): Worked well enough but they took up a TON of room (Like an entire dinning room table of space). The spools needed to be placed behind the printer and in line to...

It is a variation of this thing Filament spool holder (Credits: https://www.thingiverse.com/thing:2047554) I used the credited thing for one half and the custom half to mount it to the 2020 frame. Here you can find the complete model in Fusion 360:...

I have shortened the magic band reader holder post to be more to scale with the rest. I as well added a half inch hole through the post and the plug to be able to past wires between the electronics without drilling, half inch might be oversized but...

Keep overall weight to a minimum X and -X endstops Accessible adjustment of the Titan extruder Canted hot end cooling fan (40 mm fan) Mount part cooling fan behind X rails (50 mm x 10 mm blower) Circular distribution of part cooling air Adjustable BL...

2022 Update: fixed most annoying bug on the design - holder for gear that holds planet. It used to not support the gear properly resulting in gear jamming under sun gear. Now it should be fixed. Update comes in two parts: updated part and add on. It...

 * **There is no defined end-stop mount on this design yet** Unfortunately, with all the different belt holders, bearing setups and hotends people use on the A8, I can't really come up with an endstop system that...

The "Abdeckung " parts must be glued to the M3 nut holders of the "Frontplatte" so that the nuts cannot fall out. (Please insert the nuts beforehand). I glue PLA with super glue. In the "Gehaeuse" part there are cut-outs for M3 nuts. Please stop the...

Then just put 3D printed motor gear on motor shaft and attach the whole motor assembly to the motor holder in uicm-stator part with two small zip ties. After that, just put in two uicm-rotor parts so the gears link with motor gear and fix them with 4...

The center handle locks in and keeps the lid closed, avoiding putting any stress on the hinge to do so.UpdatesUpdated my model to keep the same spacing but different grip sizing so that different pens/pencils can be accommodated for four and five pen...

...Anyone may print copies for their own personal use, but selling or otherwise monetizing them is not permitted, and puzzle designers retain all rights as copyright holders of their work.Our puzzles are modeled using the open-source puzzlecad library.

Make sure they understand you want a ring and the star, or you might get a negative (I sent the green picture along to make it clear - the DXF only contains lines, so it's hard to tell). Added mounting holes: I used two old leather belts to make...

I moved the e3dv6 a liitle bit more down, i increased a little bit more the filament path, decreased the diameter for the filament sensor screw hole and much more.... ** 11/12/18 UPDATE 7: New way to keep the bearing with stable pressure on filament,...

It is a remix of the original spoolholder that uses printed roller arms and springs to press the spool down.To improve the stability of the arm, the profile was divided into two halves, the lower one containing the bushing and separated by a gap of...

I Recommend Hex Head screws for the enclosure and drywall screws for the hanging spool holders. 2x or more Ikea LACK tables. (I used 4 for extra storage)<br/> 2x 3M screws 15 mm long<br/> 2x 3M nuts (to replace the PSU with a printed brace)<br/> ...

I took the holders of the Y-8mm rods from the old MK3S. This makes it easier to remove the linear rails from the ball bearings for maintenance work. (Mixing with components is not recommended.)</p> </li> <li><p>The STL files of the X-axis of the Bear...