vesa camera adapter by 3d models

This is an adapter to mount a G3 or G4 camera (also fits pro model) to a Mobotix base so you don't have to drill new holes.

... All hardware needed is M3 except for the Arducam board mount, the rear pi adapter cover, and the attachment of the corner piece to the Pi adapter, where I used M2s. The pi adapter itself attaches to the side of the printer using 2 existing screws.

Three files are included: "Phone Holder - No Hole", which allows users to create a basic holder without the camera mount hole/threading; "Phone Holder to Camera Mount Adapter", which is the basic camera mount adapter; and "Phone Holder to Camera...

... lens can be press fit or glued in place at the bottom.  The adapter has inner m38 threads and outer m42 threads, allowing inexpensive M42 spacers and an M42 helicoid to be mounted above, with an M42 adapter for whichever camera mount you need.

This is a remix from the adapter that sits on around the motor for the X axis.I adapted this to support the flexi-arm camera adapter and the Picam IR Flexi Mount so that I can mount the Raspberry Pi Camera on the X Axis engine. The goal is to...

Digital camera stand to cover Toshiba TransferJet adapter for TOSHIBA TJ-UA00B See this site for more information. Sorry, This site is Japanese only. (https://kitto-yakudatsu.com/archives/4188) Print instructionsCategory: Camera Print Settings...

SynScan Wi-Fi Adapter and Camera Control Port Wiring Diagram and PCB Available on EasyEDA Visit easyeda.com/hujer.roman/wifi-for-synscan to access the design files. Firmware and FreeCad Source Code on GitHub Find the latest firmware for ESP-01 and...

Camera Adapter & Antenna Mount for DJI FPV System Installation on ImpulseRC 6" Alien The adapter is specifically designed to accommodate the unique mounting requirements of the ImpulseRC 6" Alien frame, ensuring a secure and stable installation of...

This adapter should work with most cameras and accessories that utilize a standard tripod mounting thread. ... To create this adapter, you will need a 1/4" x 1/2" UNC bolt, similar to the one found at...

You'll definitely want to customize the adapter so it's an exact fit for your camera, as not all GoPro type clones are the same size and it won't work well if it's not a snug fit. For example, the defaults are set up for a GitUp Git2P, which has...

To build this adapter, you will need an additional non-metric nut that fits standard camera stands. If you don't have one, you can print it from thing:2501430. After several pre-design iterations, I determined that three LEDs provide sufficient...

... I fitted PS3 Eye holders on my Ender 3 and discovered that the PS3 Eye has a larger base than my EyeToy. To fit my EyeToy snugly into these new holders, I created two adapter cases: one with a rounded shape and another with a straight design.

This is a custom adapter made to attach onto the front of the HobbyKing Pan/Tilt FPV camera mount (https://www.youtube.com/watch?v=-iiJ1rike-s). I'm using it in my latest build series, where I'm putting together a HobbyKing Bixler with iNav 2.1 and...

This is a camera adapter mount for the sidewinder x1. For the version on the right: You will need 2x M4x28-30 screws with T-Nuts to mount this with the blue default plate for the pully mount. For the "left version": Just use a bit longer...

... 6SE telescope to capture the moon. I also added the STEP file in case you need to modify something for your cameras. Full story with details on my blog here: https://www.schweinert.com/3d-printed-telescope-adapter/ https://youtu.be/wzuBMtXnnnw

... 6SE telescope to capture the moon. I also added the STEP file in case you need to modify something for your cameras. Full story with details on my blog here: https://www.schweinert.com/3d-printed-telescope-adapter/ https://youtu.be/wzuBMtXnnnw

This adapter gives you the ability to use super high quality Camera Butter filters and lens protectors on naked GoPro cases that have a round lens mount similar to the DJI Mavic 2 Zoom, such as the Beta FPV Naked hero case. These are the filters to...

I used ironing on the surfaces to make the adapter fit the PCB perfectly. Use the 3MF file to generate your GCODE if you use Prusa Slicer too.Full story with details on my blog...

The camera was swiveling and not properly supported, so I added another ring to stabilize the adapter and prevent it from falling out. 4. I created a hole for the other binocular lens to use as a focus aid. This proved incredibly useful, especially...

I possess two car DVR units, each of which is plagued by faulty components. ...To compensate for the shortcomings of these devices, I constructed a custom adapter, effectively merging two broken units into a single functioning DVR system.

... Print this file. 3. Slide the Ultimate Sturdy Mount into the rails on the left side of the Ender 3 V2. 4. Affix this adapter plate to that mount using a small metric nut and bolt. 5. Use a tripod screw to mount your camera to the adapter plate.

Fitting a fast camera lens to a sensitive astronomy camera gives you the ability to take deep wide field images for spotting meteors, asteroids and satellites. This adapter permits lenses with a Pentax M42 screw thread (easily available on online...

All of the details, basic theory, and how-to's are in this blog posting: http://www.siliconsombrero.com/2018/04/28/scopecam/ This adapter connects a Nikon F-mount camera to a standard 38mm ISO photo tube port. 38mm ISO ports are found on older...

FPV micro 19mm camera adapter combined with front mount for TBS Crossfire Immortal T V2 antenna in one peace for ImpulseRC Apex 7"/6"/5" frames (or replicas) with default 5mm hex standoffs. Designed lightfull for long range cinematic flights with...

In contrast, studio bars feature a wider 100mm spacing and sit a full 118mm from the lens center, offset by a precise 17.25mm for optimal camera stability. For creators who demand flexibility and versatility, a range of STL files is included in this...

Adapter to convert a GoPro mount to a 1/4 inch/Camera mount. The way this is designed, you can glue the two parts together with a 1/4 in.-20 x 1/2 in. Hex Bolt embedded. Use CA glue, I usually use Loctite 406 and I've never had a part break. Extra...

Assembled with M3 bolts, nuts, and an M4 bolt, the adapter requires careful alignment of the ocular and iPhone camera. ...Custom alignment is planned for future versions, along with sliding screws for part positioning, iPhone bottom lock, and wide...

An adapter for two concentric pipes fits the Princeton Instruments Pylon CCD camera's shutter, blocking stray light from reaching the sensor. The outer diameter of the larger pipe is around 114 mm (4.5 inches) and the smaller concentric pipe's outer...

Two slots were subsequently added to enable attachment of the adapter with a cable tie to the projector, which proved effective in conjunction with the existing slotted tab that fits seamlessly onto the adjustment screw at the bottom. ... The...

Printing Settings Printer Brand: RepRap Printed on: Prusa i3 Printer Rafts: No Supports: No Resolution: 0.3mm Infill: 10% 3D honeycomb+15% 3D honeycomb Notes: All parts are in a single file, but I personally print the camera base (the top component...