venturi garden hose attachment 3d models
258905 3d models found related to venturi garden hose attachment.thingiverse
To do so, print the designed venturi part and follow these steps: remove the support cylinder and cut the membrane; attach a rubber washer to the female threaded end; tap the vacuum port with a 1/8 NPT tap without force; insert your desired fitting...
pinshape
SummaryI designed this to mix a small amount of liquid fertilizer into a stream of water from a garden hose. I have a worm composter that produces quite a bit of liquid fertilizer and I wanted to dilute it and sprinkle it on my lawn.InstructionsPrint...
thingiverse
Garden hose attachment to break the hard stream. ... Inspired by https://www.thingiverse.com/thing:5181441
thingiverse
I'll create a venturi-style water pump for sucking water from buckets or ponds using water pressure from a garden hose. And to the initial few dozen downloaders, please delete and download again. After experimenting with that first version for...
thingiverse
Connect a standard garden hose and immediately gain access to a powerful high-pressure hose via an added O-ring.
prusaprinters
Print with support only for the lockpins, the remaining of the adapter is at a 45 degrees angle in the inside to push the air in the hose.To be use with a cordless compact blower to make it easy to work outside instead of using a big air compressor.
thingiverse
This is an accessory designed specifically for washing climbing or repelling ropes used in gardening applications. The intended diameter of the rope to be cleaned with this tool is precisely 12 millimeters. ...To ensure maximum sturdiness, I decided to...
thingiverse
... hose. I use this to run half of the water output from the pump through a length of black hose, heating from the sun. ...Then it returns just before the electric pool heater, helping reduce the amount of energy required to heat the water to temp.
thingiverse
The "Garden Hose Venturi Pump" underwent a crucial redesign after the fins on its manifold began hindering its performance. To rectify this issue, the fins were meticulously removed, allowing for a more streamlined flow of water through the system.
thingiverse
The Venturi is a compact, efficient, and stylish aerator specifically designed for residential use, allowing homeowners to experience professional-grade performance right in their own gardens. By using the unique principles of vortex creation, the...
thingiverse
> May 27 2020 -------------------------------------------------------------- -------------------------------------------------------------- Venturi Pump with a few added features from the original creator Features: -Extended suction inlet and...
thingiverse
... was taking me minutes to do before now takes seconds, exactly what I wanted! I struggled to get the garden hose threads right, 0.75 11.5 NH thread, until I found a Fusion forum where someone made an XML for this thread and it worked beautifully!
thingiverse
We had some big problems with flooding on our patio during the winter months, so I designed this garden hose siphon attachment that gets the water level down lower than a regular hose could while on its side. This also features a few tabs to rest...
thingiverse
Currently, it's a straightforward sprayer coupled with a bottle attachment for nutrient supplements during watering, but lacks any means of regulating water flow directly from its source. A 23mm valve controls additive release from the bottle,...
thingiverse
If you search for this type of design (Infinity Jet), you'll find that it's used in gold sand dredging and ROV substrate removal, touted for its efficiency and unclogability; however, the available sizes start at 2", which is far too large for a...
cults3d
Garden Hose Attachment for washing dog/pet paws! ...just attach to the hose holding the specified spot and then turn on the water, run each dirty paw foot or hoof through the rinse until clean, dry thoroughly with towel before putting back on ground.
thingiverse
Customized version of https://www.thingiverse.com/thing:29100 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=29100
thingiverse
Customized version of https://www.thingiverse.com/thing:29100 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=29100
thingiverse
Customized version of https://www.thingiverse.com/thing:29100 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=29100
thingiverse
Customized version of https://www.thingiverse.com/thing:29100 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=29100
thingiverse
Customized version of https://www.thingiverse.com/thing:29100 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=29100
thingiverse
The Tevo Tarantula and Ender 3 are being utilized. A YouTube video showcasing this setup can be found at https://www.youtube.com/watch?v=BP5C7eAYZd0. ...Please take a moment to subscribe for more updates.
thingiverse
This is a drop-in replacement for "TheFlange" from Walnettos original design that is fitted to connect to a standard garden hose (works with US hoses not sure about other countries). I have also included an insert that funnels down the 5 gallon...
thingiverse
Connect the sphere to a half-inch garden hose using hose clamps. 5. Before proceeding, give it a quick test by applying some pressure to see if the hose starts dancing (if you're unsure what this means, just try it). 6. Once ready, feed the head of...
thingiverse
Apply a thin layer of Teflon tape to the threaded end of the Garden Hose Connector/Adapter.
thingiverse
This is a remix of Blue Waves/Summer Waves-Intex Pool Cleaner Adapter by bdub_24 that has a male garden hose attachment on the end instead of what it had before. I cut the end off of the garden hose adapter by jackout to get the garden hose part.