velka 3 case 3d models

NEW - version 6.1 (tested with PETG) Version 6.1 TPU for flexible material still untested Version 6.1 in two pieces, tested with PETG --------------------------------------------------------------------------------------------- New version V6.0 A few...

This file is likely a template for a phone case design generator. Based on the parameter names, this seems to be designed to work with Slic3r, an open-source slicer software commonly used in 3D printing. ... However, without more information or context...

A custom printed case was created to ensure a perfect fit, with an opening for the ethernet jack on one side and a recessed area at the top for hookup wires. Snap-fit pegs make it easy to assemble, while V2 features holes for removing the board if...

The next generation of Voltmeter and Ammeter cases is here, featuring a sleek new design that showcases your valuable devices without cluttering the space. A minimalist aesthetic has been adopted for this edition, eliminating the display window to...

This is a case for yet another hardware revision of the Proxmark3 Easy. This one came from dangerous things but it may not matter. Either way, This fits my version. I have included the original IPT files so that the positions can be modified of the...

... Xbox into a brick. Keep all those original HDDs with this handy case! Printing: * whatever infill * can get pretty tall with layer height Looking for more Original Xbox stuff? ... Check out this: https://www.thingiverse.com/thing:4899449

The base holds the ender 3 board and fan, a raspberry pi with octoprint, a buck converter, and the power supply the posts in the back need raised for the pi to get the usb over the buck converter but I just used some spacers left over from a wall tv...

The base holds the ender 3 board and fan, a raspberry pi with octoprint, a buck converter, and the power supply the posts in the back need raised for the pi to get the usb over the buck converter but I just used some spacers left over from a wall tv...

A comprehensive setup guide for the SKR 1.3 motherboard, tailored specifically for the 2020 profile and used with the Tronxy X5SA-400 printer. ...This configuration allows for the installation of an 80x80mm fan on the cover.

This is a further development of the stand for the Raspberry Pi 3.The stand is only plugged in.There are 2 versions one with short air slotsone with long air slots

Remixed from Pixel 2 to 3, added a back with some rando hexagons. ... Printed in TPU, was a bit of a challenge getting my settings dialed in on this one.

This design was crafted from scratch to accommodate either the Creality or MKS Gen L mainboard, alongside a Raspberry Pi 3. ...Additionally, it's optimized for two 80mm fans that stand just 10mm tall.

Hello,\nI'm using a tiny profile designed specifically for the Raspberry Pi 2 and 3.\nPrint Settings:\nPrinter: DaVinci 1.0 pro\nRafts: Not necessary\nSupports: Not required\nResolution: 0.4 mm

I'm showcasing a comprehensive 3-part scenario featuring four innovative NeoTrellis boards, meticulously crafted for a compelling YouTube video project. ...Check out the full video at https://youtu.be/Lo17JRFn0kU.

The GoPro 3 FPV is equipped with advanced features such as live video streaming and first-person view capabilities, allowing pilots to experience real-time action from the pilot's perspective. ...With its sleek design and powerful performance, this...

Suggestions for the top case design, especially regarding stepper/term/endstop contact openings, are welcome. First prints have revealed some adjustments needed, such as hole dimensions and positions, alignment tweaks, and potential replacements for...

So I designed it based on the one that come with Ender 3 in sheetmetal.To secure the fan on the top part, the motherboard on the bottom part, and to screw the top on the bottom, I used M3 threaded inserts and allen screws.The holes to the motherboard...

This is a unique design for a Gopro Hero 3+ cover that effectively conceals the led lights on the camera's front surface.\nCreated with PLA at a precision of 100 microns, this print required approximately 40 minutes to complete. ...To ensure a snug fit,...

... screws - you'll need four of them. ...Alternatively, just pick up a pack of four at your local store. The Raspberry Pi 3 needs these screws to function properly, so make sure you have them on hand. ...I hope this little project turns out well for you.

A straightforward justification for opting for a Raspberry Pi 3/3B model paired with a heat sink is rooted in its uncomplicated design and affordability, making it an attractive choice for beginners and experts alike seeking to build a low-cost yet...

Custom Enclosure for the Orange Pi 3 Drill Holes: 2 Millimeters in Diameter Reach out to request a tailored design featuring unique holes, vents, or heat sinks if needed, and I'll provide you with the corresponding F3D file upon your request.

... drawing inspiration from a similar design on Thingiverse (http://www.thingiverse.com/thing:991183). ...That creator had remixed his own work earlier, prompting Sarah to imagine a modified version of her GoPro 3 camera housing - and this is the outcome!

This is a custom design for a protective housing built specifically for the GoPro Hero 3 camera, allowing users to securely store their device along with two additional batteries and two spare memory cards within the same enclosure. ...The intended...

Design Brief for Custom Display Housing Construct a sturdy enclosure to fit a Nextion 3.5-inch display module. The housing should be crafted with precision to accommodate the device securely. Materials Required: * High-quality M3 nuts *...

... sensors and actuators, giving you total control over your mill's movements. With a Raspberry Pi 3 at the helm, you can say goodbye to expensive proprietary systems and hello to cost-effective, DIY milling solutions that put the power in your hands.

...Feel free to share your thoughts on this project. Here's how I designed it: The materials I used include: 1. Raspberry Pi 3 2. Tailor's tape (I'll be investing in a vernier caliper soon) 3. A pen and paper for calculations 4. ...Basic geometry math

This Thingiverse design template offers a handy solution for Gillette Mach 3 razor users who want to carry their razor safely and securely on the go. The take-along frame is specially designed to hold the razor in a compact and lightweight frame. It...

The Raspberry Pi 3 is a mini computer that packs quite a punch in terms of performance. It has a 1.2 GHz quad-core processor, 1GB RAM, and built-in wireless LAN and Bluetooth connectivity. This makes it an ideal device for a variety of applications...

... mount with rounded corners. You can find more information about this fantastic camera on the Banggood website: https://www.banggood.com/RunCam-3-64G-HD-1080p60fps-NTSCPAL-155-Degree-Wide-Angle-WiFi-FPV-Camera-p-1127476.html?p=QK2903081680201209NS

http://www.thingiverse.com/apps/customizer/run?thing_id=57281 Instructions Using the Following Options: Label Text -18650 Battery Diameter-18 Font Type - write/orbitron.dxf- Fit Gap -0.1 Base -0.8 Inside Height -66 Label Depth --0.8 Wall Thickness...