vee packing seal design 3d models

Set the eye dimensions to 0.6cm to put them in the proper place. How I Designed This: A partner and I were given a 3D-printed ghost, and we started by taking measurements of said ghost. To ensure we had the same measurements, Edwin and I...

Firmware Repo: [Marlin 2.0.6.1 for prusa mini custom build on MKS Robin E3D V1.1](https://github.com/foobarjimmy/MKS-Robin-E3D-1.1-Marlin-2.0.6.1) Instructions&compiled_firmware Repo: [Wiring&Precompiled firmware for prusa mini custom...

Dremel Pillar Drill (Drill Press) Precision pillar drill stand for a Dremel giving a plunge depth of about 70 mm.  Any Dremel that has the ‘standard’ 16 mm screw at the business end should fit but I’ve only tested this with the Model...

Set the arc to have a diameter of 0.75 cm.Create the same arc three more times so there is a total of four arcs going along the top construction line(All arcs should be equal in size). Design Choices: When my partner and I were following...

 Installation:For clarity sake, any part descriptions based on axis names (X, Y) are given using original default axis names, with their intended new designations (for after the swap), sometimes shown in parentheses.  Detach the X belt (soon to...

Then reassign the pin assignment at the limit switch according to the designations (G-> G, S-> S, 5V-> V). Actually, you can already test the whole thing: With the G-Code "M119" you can query the status of the end stops. But please do not drive...

Change the font to Impact and adjust positioning and size to your desire.Indent the two letters to 0.1cm using the extruded cut tool.Design Choices:We first started off by looking at the model and drawing a diagram with 2x the dimensions so each...

Here you will find a list of all the components, all 3D models, firmware and designs of power distribution boards (Gerber_Servo PDB x6, Gerber_Fan Light) that can be made to order. But this is not necessary at all, the boards are very simple and can...

This is a small missile I built for use with a sci fy model. Designed on Tinkercad.Enjoy!~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~More fun stuff:Construction:Building under construction...

The text and font of the squares can also be edited.This design has a few features to make it easier to print. Elephant foot is less of an issue because the bottoms of the internal squares are chamfered. The gap between pieces can be changed...

- Replace the stock extruder mount by the filament sensor holder This work is based on the original Superfly extruder design by Mustcode https://www.thingiverse.com/thing:4841682...

UPDATE: 20.04.2022adapterplate (new design) for model C Hello, we would like to introduce you to our stealthburner conversion mod. At this time it works only with the klipper Firmware. The use with “Marlin” is planned later and will be...

This involves files from the original sources as well as modifications made for this design specifically. I am also including the Fusion 360 file for any remixes! :)Parts to print1x cover_4040_extrusion_cut (for covering the extrusion hole in the...

It was quite hard to imagine all the fine details, which make the hands of the watch turn, since you simply couldn't hold the mechanism in your hands and turn it around to inspect it.Therefore I designed this fully 3D-printable clock-escapement...

The pod bay is designed to be assembled separately and then fitted inside the sphere. EVA Pod Model I used BouncyMonkey's EVA Pod Model in my build. However, his model was meant to printed much larger so some fine detail is lost in the...

The motor supports designed for a 4-hole M3 mounting with a 25mm diameter can be used as feet or 7.5mm square aluminum tubes can be inserted. Mounting the camera on a rostrum towards the front should allow a comfortable viewing angle. Pay...

Please note that this flying stem is intended for general use with flier and skimmer miniatures, and not designed specifically for use with the Nautiloid. It is still serviceable in this capacity however. Using transparent filament for this model...

The suggested power is designed around what I have found easiest to source and less expensive. It was also elected because it can take an easily sourced prop (5") and with max battery (4s) can product approximate 2:1 thrust to weight ratio. I have...

Ready to pump your promethium, sweet crude, or whatever lights up your day!Designed on Tinkercad.No supports required.Superglue the valve...

... box 1 Shell_0.2mm_PLA_MK3S_4h52m.gcode</i></code></p><p>The outer shell and the lid to the chamber. NB! Correct orientation/support design is important!Parts in this file:&nbsp;ShellChamber lid&nbsp;&nbsp;&nbsp;&nbsp;

My dock design is [posted separately](https://www.thingiverse.com/thing:5345188) as it is not dependent on this toolboard mount or even this extruder setup. In future, I plan to add support for the stock aluminum gantry... the hole pattern is a...

My dock design is posted separately as it is not dependent on this toolboard mount or even this extruder setup.In future, I plan to add support for the stock aluminum gantry... the hole pattern is a bit different so this one only works on the CF...

The 3D printing model's chosen scale is 1/34 for the FFF/FDM version and 1/68 for the DLP/SLA/SLS version.VERSIONS' SPECIFICATIONSFFF/FDM 1.0 version features:- Contains 90 parts;- A printed model is 648 mm tall, 633 mm wide, 344 mm deep;- Assembly...

Main featuresTwo-part (base and cover) parametric coaster.Fully customizable.Customizable modifiers for the parts.Several predefined grid types, that can be combined, and a do-it-yourself "infill" coaster cover using the modifiers.Z-based color...

PrefaceThis head was designed specifically for smaller printers, with a minimum build area of 18cm x 18cm x 18cm and to use comparatively little filament (a little over 200g), while still holding up against accidental abuse. If you don't own a 3D...

The author of the 3D printing Hammerhead Corvette model did a perfect job depicting the time-honoured design of the warship and paid utmost attention to the intricate details of the vehicle’s exterior. Make sure you 3D print your own Hammerhead...

Deeply impressed by Rob Bottin’s practical effects and the alien’s uncanny design, our contributing 3D artist spent 174 hours on sculpting Norris assimilated by the Thing from the iconic “chest chomp” movie scene. The author of the model put his...

This design combines two 4x microscope lenses together to create a stereoscopic 3D macro lens, with 2x magnification and a 5mm stereo baseline. It has been designed to be shot handheld in the field using a flash for lighting, rather than in the...

All thanks to him.All parts have been redesigned to fit the new design.What's new?- Added the possibility to use Parkside x20 batteries. It can also be used connected to a 12v dc adapter. &nbsp;<strong>By mounting the dc adapter that I attach in the...

Either way, it will look great for the superb miniature you invest your time and money into.The aliens are coming, and there is nothing you can do to stop them, except fight!  Shelter yourself!Deliver your cargo!Get back in the fight! Designed on...