vector offroad jk dash bar 3d models

I purchased the Vector Off-road JKE full bar link for my 2018 Jeep JK and its really been a great product. The one thing I didn't like was the messy wires hanging down to the USB power plugs. I needed a way to power the mounted electronics, without...

I purchased the [Vector Off-road JKE full bar](http://https://vectoroffroad.com/collections/jk-wrangler-products/products/jke-dock-2011-2017/) for my 2018 Jeep JK and its really been a great product. The one thing I didn't like was the messy wires...

The Vector Offroad JK E-Dock is a great way to mount electronics in a Jeep Wrangler JK. However, the USB power cables can be unsightly and get in the way. This print adds 4 DC power ports, each with two USB jacks to the top of the dash, keeping the...

2007–2018 Jeep Wrangler JK/JKU Dash Mount ==================== This dash mount will allow mounting of 3 devices on a Jeep Wrangler JK or JKU. I'll be adding additional mounts in the future. Ram Mounts --------------------- The v2 Ram mount is...

This fits a 2011-2018 JK. This is a push fit design. The inlay replaces the factory inlay and just pushes into place. The letters will need to be printed with a negative horizontal compensation from -.10 to -.20 depending on the printer. This...

This is a cover to insert in the factory cubby hole that is in a jeep jk with manual windows. It allows for a usb port and a ball mount for a car phone holder. The plate is held in place with two screws using the factory holes in the bottom of the...

Building a phone holder with a dash mount, I intentionally added some extra space in the design to accommodate my phone's protective silicone case. ...The new version, V2, features a slightly wider border around the edges, coming in at 4mm compared to...

... ...This was modeled for a 2008 JKUR Jeep Wrangler Unlimited Rubicon, but should work on the first iteration of JK's (2007 - 2010) regardless of trim level. To install: 1. Slide the left side grab bar cover off (it slides towards the driverside) 2.

This is a offroad LED light bar for your scaler/crawler or offroad truck. You just need 150mm of the classic 8mm wide LED stripes. On one side of the housing is a small opening for the cable. The overall length is 154mm with the supports 158mm.

This is an LED holder for the Eaglemoss Vector V3 3D Printer.\nI created it to accommodate seven 5mm LEDs, which can then be connected in series without any additional resistance, and only consume a total of eighteen milliamps.\nI linked them...

Am thinking of adding loop to allow securing to hanlde bar with a cable tie - although the fit is quite tight so is probably not needed, but a nice to have for peace of mind. ... This print allows for the tyre pressure monitor display on left (single...

This is a cover to insert in the factory cubby hole that is in a jeep jk with manual windows. It allows for a usb port and a ball mount for a car phone holder. The plate is held in place with two screws using the factory holes in the bottom of the...

This is attached to the inside of the dash cubby, with two sided tape and rubber debris catch still in place/removable. The small v notch could be a bit smaller, but wanted to be able to remove the debris catcher after installation. The 17mm ball...

Vector

If you bought one of those 6D LED bars for offroading and you need it removable, use this magnetic mounting bracket. It makes it attachable by neodymium magnets and makes it less police magnet as a result. At least if you put it in your trunk when...

FAT VECTOR

dash

... or fictional character, but rather a fundamental tool in physics, engineering, and computer science. Vectors are used to describe forces, velocities, and accelerations, making them an essential component of our understanding of the physical world.

Vector presents a strategy for addressing the rising number of automobiles on Pakistani roads due to increased economic activity. As business booms, so does affordability and ownership of cars. Could public transport be an answer? Possibly...

KRISS Vector, a cutting-edge pistol designed for extreme situations, unleashes its fury on the world of firearms. Built around a steel receiver and featuring a unique recoil-reducing mechanism, this firearm delivers unmatched accuracy and control. ...By...

This single vector can be constructed by combining three distinct components, allowing for an extended design that can be linked end-to-end or in a head-to-tail configuration. When printing multiple sections, they can be connected seamlessly without...

Check it out: https://www.thingiverse.com/thing:2355327 Initially, I used bungees to hang items from the horizontal top bar, but finding and releasing things was a real challenge. After three failed attempts (PETG is notoriously flexible), I...

Flexibility and durability demand a precise 3D printing method, namely, the one that yields exceptional "fingers" to accommodate varied environments, paired with a substantial strength output in its structural build. ...To guarantee stability at the...

Here are two simple spacers to securely fasten an OPT7 50-inch light bar to a JK Jeep, utilizing Rigid Industries Light bar mounting systems. If you found this helpful, show your appreciation with a thumbs-up! ...Cheers, Stanley.

This bracket allows the dash to sit on the riser itself rather than relocating in another area by other means. Due to the relocation of alot of dash wiring, I had to make an outward semi circle to accommodate space for it so it wouldn't pinch the...

I just added some side supports. Might not be necessary, but made me feel better, lol! ... Remixed from: https://www.thingiverse.com/thing:4846219

Created by StevenAm2010, this impressive 3D model showcases his skillful use of the 3DTin software to bring his vision to life.

Customized version of http://www.thingiverse.com/thing:40705 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=40705 Instructions Using the following options: manual_width = 100 message_two = GET AWAY...