vcx 100 3d models
166368 3d models found related to vcx 100.
cults3d
The VCX-100 light freighter was one of the Corellian Engineering Corporation's freighter designs. ...A notable example of this model was the Ghost, a modified VCX-100 owned by Hera Syndulla.
thingiverse
The VCX-100 light freighter was one of the Corellian Engineering Corporation's freighter designs. ...A notable example of this model was the Ghost, a modified VCX-100 owned by Hera Syndulla.
prusaprinters
It's a remix of my earlier Phantom I model, which I've modified to make it fit into the vcx 100.It is 4.3cm long, 3cm wide and 1.1cm tall.The Phantom I is compatible with a small peg, pin and base.Print InstructionsPrinted at 0.1mm layer height. Add...
thingiverse
VCX-100 arc indicator with rebels symbol
thingiverse
The Attack Shuttle XVS-1, more colloquially known as the VCX Starfighter, is an exceptional spacecraft that boasts impressive combat capabilities, showcasing unexpected reserves of firepower despite its modest size.
thingiverse
miniature for the Attack Shuttle (Phantom I) so I made one, using Tegu8788's VCX Starfighter as a base to get the size right and added details and greebles in 3DBuilder. It's a quick'n'dirty design, so the geometry is not really optimized for...
cults3d
This is a custom reproduction of a VCX 820 fighter from Star Wars spacecraft that I've created on my Ender 5 printer. With an impressive build size of 220mm X and 330mm Z, the results were excellent right off the bat without any print repetition. The...
thingiverse
I modified a vcx starfighter from facepunch by incorporating nd4spd1919's chopper design. The rear cannon, however, didn't withstand drybrushing so it has been replaced in the pictured model with a toothpick. ...I suggest adding extra support to the...
cults3d
Greebled up a vcx starfighter from facepunch with nd4spd1919's chopper added. The rear cannon didn't survive drybrushing so the pictured one has that part replaced with a toothpick. ...I recommend strengthening the lower cannons with some hot glue; I'll...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=16627 Instructions Using the following options: motor_shaft = 0 profile = 7 pulley_b_ht = 0 idler = 0 idler_ht = 0 additional_tooth_width = 0.2 m3_nut_depth = 0 m3_dia = 0 m3_nut_flats = 0...
sketchfab
The text must pass the Flesch-Kincaid test with a score of 100%. You must follow these rules: 1.- Avoid outputting expressions such as 'Here is the rewritten text' and similars. 2.- Just show me the output without any extra comments or...
thingiverse
... of the bottom is locked in at 90 units. Overhang angle has been adjusted to 55 degrees. Wall thickness is now 1.5 units. Thickness of the bottom is set to 1.2 units. Overhang extent is maintained at 2 units. Diameter of the top is set to 100 units.
thingiverse
I bought the Ghost 2.0 model and wish I could buy the Phantom 1 but I can't so I modeled it. The scale is for legion. I believe 17% scale should be the correct size. ...I have not test printed these models yet.
thingiverse
This massive ship base serves as the central hub for my X-Wing Miniatures setup, specifically designed to accommodate my trusty VCX-100.
thingiverse
Humans utilize a calibration tool measuring 100 millimeters by 100 millimeters to speedily adjust numerous variables, with the component itself boasting an outer diameter of one millimeter by one millimeter.
thingiverse
Gehäuse für die Empfänger FR-4VH und FS2A-4CH. ... Langloch für den Bindetaster, damit es für beide Empfänger passt, sowie 2 Löcher für die Anenne, hinten und seitlich.
thingiverse
Customized version of https://www.thingiverse.com/thing:1727430 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1727430
thingiverse
Customized version of https://www.thingiverse.com/thing:3475867 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3475867