vcarve files 3d models

 Quite a few years ago I made a series of aluminium versions of these with full laser tag electronics inside, working 'clips' that changed the damage done, full sound and lights etc.I decided as I still had the svg files I did to get the panels...

(also may use DFX file for Fusion360). 1 x HotEnd Fan Cage, v2 (ABS!!!, print flat, RE picture, no support) borrowed and re-mastered from HeroMe at: https://www.thingiverse.com/thing:3092044 2 x M3x8 (mount to HotEnd Plate) 2 x M2.4 screws (mount...

Please note that some shades consists of four .3mf files, other shades have only a single .3mf that should be printed four times. You might consider using my good old temperature correction script for the wipe tower, as found in:...

:) Modification IdeasPlace a battery or a small power bank inside the base and convert it into a portable fanUse an Arduino or a Raspberry Pi to control the fan Updates2020-08-20 Updated the list of materials. Print instructionsG-code...

The idea was to bring a superlight direct drive extruder to the SR by integrating it to the housing and getting the motor as low as possible above the effector plate Want a lighter setup, check my deported blowers system ;-)...

Otherwise you will run into troubles.Download & Printing Instruction Either download the file: "Filter-Infinity-All-Parts-Right-V22.stl" and "Filter-Infinity-All-Parts-Left-V22" (if you want to have the left fan too) and split the parts with the...

Credits ------- OpenFLex is based on and remixed from: https://www.thingiverse.com/thing:2740279 https://www.thingiverse.com/thing:1508410 https://www.thingiverse.com/thing:3393468 https://www.thingiverse.com/thing:1758162 License ------- Creative...

I couldn't find an easy way to export a STL or 3MF file for broader compatability, so if you've got a method that works for that please feel free to share it in the comments. :)</p><p>Settings for printing the logo layer:</p><ul><li>Preset:...

I didn't tested to print them yet, because it were tiny issues, I did fixed them on my initial print easily by filing and drilling a little bit. The fixes are just for perfection. * TPU, PETG, PLA are all tested. TPU had some extrusion failures...

Now with the Gen2's rail design you can quickly swap the storage units between work areas.Download the GEN2 Interactive Catalog PDFFeatures:• Gen2 rails allowing quick and easier swap-ability and combinations of many Gen2 Storage System designs.•...

... designs for conversion linear in to rotary motion and last but not least I learned about the importance of tolerances and I hope those work out for anybody printing this. If not I will also post the OpenSCAD files soon, after I've cleaned them up!

For those whose LowRider v3 MPCNC has or will have a BTT SKR Pro 1.2 main board and a BTT TFT35-E3 v3 touchscreen, I offer my remix of Ryan's blank case CAD file. This case may fit other SKR boards, depending on dimensions. Check before printing. It...

- Updated Bottom and Middle frame .stl files. Moved filament path to interfere with MK8 drive gear a bit more. Also adjusted where MK8 drive gear sits in relation to the filament path to try to center the filament with the knurl better. Moved rear...

Moreover, I merged the initial publication with a multicolor lamp shade pattern. The lamp measures around 15cm of height, and 40 cm in diameter. Basically, you need to print a lamp base (two 2-material .3mf, around 8 hours in total), a ring (single...

&nbsp;This means using a bolt of 35 mm (M4 or M3 will do) for the pivot.By the way, to access the Dremel chuck clamp you can…A) loosen the M3 corner screw on the upper_pillar_clamp and turn the Dremel roundB) take the rubber bands off and drop the...

Fortunately after smoothing, the dissolved PVB acts as a kind of glue that improves the bond between the two materials to a certain degree, where I gues it will work for most situations.Composite Printing PVB and PETGIn the downloads of this project...

The STEP files are included for easy Remixing though. I have zero qualifications for designing a filter, so this is strictly an at your own risk deal, and I make no guarantees on if it will work in whatever application it may be used in. I printed an...

This little thing today is the strips of this box.The project archive contains files in DXF format. I do not think that someone will come up with the idea of printing them on a printer, but having a laser or at least a small table saw - it is quite...

You can use the menu `File` / `Show library folder...` to open it. Then include the library at the beginning of your code with: use <davel.scad> ## Common parameters To draw a bevel or a buttress you need to know: - **where** you...

If this is for a Taz, cut off approximately 14mm of the end shaft, and file down the notch until that piece fits inside the press fit drill bushing you will install on the extruder transmission cover later. </li> <li>Remove the door stop end from the...

I used this to get my (currently) world record bedslinger #speedboatrace benchy at only 4m 48s.After trying other people's designs and having issues or bad performance as they always lacked something or another, I finally decided to design my own X...

All in all, I believe your satisfaction with this mask should be limited only by the skill with which you make it, and not by any features of the design.Hope I won’t see any more comments to this design base on general 3d print issues(rough surface,...

Making these changes will not make the printer silent by any means but the noise level is lowered considerably.DonationsAll my designs are free, they're developed and tested in my spare time and most have source files available for easy editing.If...

I have prefixed all new files with V4 and uploaded new images.UPDATE 4/5/2020: Added Dual Fan Duct v5, this is a very different approach to dual fans compared to v4. It is basically a heavily remixed RHD fan duct adapted for 2 fans. This improves...

I didn't tested to print them yet, because it were tiny issues, I did fixed them on my initial print easily by filing and drilling a little bit. The fixes are just for perfection. TPU, PETG, PLA are all tested. TPU had some extrusion failures...

¤verrouillage du programme 1 minute en cas d'erreur sur le mot (et mémorisation du verrouillage dans l’EEPROM pour éviter une réinitialisation par enlèvement de l'alimentation) Pause when printing to insert the lid M5 nuts edit 20/10/19: add the...

You will also need to disable Brim, Skirt or Raft to make this fit!Then use these files:optional-side_left_part1optional-side_left_part2optional-side_left_part3instead of:side_left_half-upside_left_half-downScrew them together to make the part...

You and your partner&nbsp;MUST have identical files that you create by collaborating on each step, one at a time. This ensures that your projects are accurate and efficient.</p><p>Presented ghost clip model in question:</p><figure class="image...

for PLA+ (.3mf and .gcode are in 0.15mm with the .3mf being optimized for Prusa MK3s+ Printers that are well calibrated or factory calibrated)  Hot-End Temp: 220-225 for first layer smush and good adhesion if not using brim (not suggested since...

The coils themselves were created a little narrower, since about 15 meters of AWG30 wires fit there, this is a decent margin, and the place on the table during operation is quite limited ...Also among the files I added a Frame in DXF format, if you...