vblock file 3d models

This can be useful for recording long time lapses, inside cars, inside airplanes, and other hot places with little air movement (and especially when the camera is recording and plugged in.) I designed this to use parts I had laying around, so...

**Building the model** Colors Black: (Paramount3D PLA - Black) eye_black_right eye_black_left tail_left tail_right tail_onpiece (optional piece) mane eyebrows (file contains two identical pieces) .. Skin: (Polymaker PLA - Army Beige) face .. ...

That´s why the source file includes a filament ring like the ones included with the dryer, just without the tray area. However, even so my printer can handle the size, it would be a long print and I would require around 8 or 9 of those prints. We are...

(if you want links to these print test files let me know) Parts list: -2xM3*Xmm button head screws (Mounting @ top of heat block) The Same screws used on the stock setup will work Be careful not to overtighten these to prevent cracking -2xM3*Xmm...

You have to edit a config file with Unix compatible tools on the SD card to change the camera settings - these settings control resolution and the photo interval timing among other things, and you have to remove the still images off the SD card when...

Depending on your printer’s tolerance, you may need to trim/file the recess back slightly to get a nice snug fit for the roof. Because the floor elements are rounded, the actual floor is split in half to give a flat surface to contact the print...

If your bed size is less than 230mm then you'll want to edit the file using a text editor and change this line: > G1 X10.1 Y200.0 Z0.3 F5000.0 ;Move to start position The Y200.0 says to move the nozzle back 200mm, but if your bed is too small I'd say...

The readme.txt file contains a Bill-of-Material considering bolts an nuts. I recommend this as a component fan: https://www.thingiverse.com/thing:4818630 This component fan fits perfectly with the air duct. Of course, anyone else can also...

This is completely sufficient and has no effect on the stability!Supplies: Super gluStep 1: PreparationPrint files:• Fruit bowl_sidepart.stl (2x)• Fruit bowl_bar.stl (16x)• Fruit bowl_foot.stl (2x)Print SettingsPrinter brand: PrusaPrinter: i3...

(The ATV fuse box I used is not listed anymore on Amazon, I attached a picture of what I found that was similar) UPDATE 9/9/2017: I had to make another PSU (and the box I could find was different again) and while doing that I thought I would learn...

 Use a centering tool to ensure the base place hole is centered with the collet.Printing InstructionsSet Layer Height as desired, I used 0.3 mmUse 4 perimetersUse 25% infillMaterial of choicePrint files in the orientation as downloaded.  Use a...

If you need, ask me for the Fusion 360 .f3d files to make your own adaptations, I'll provide them, no problem. The parts of the support box can be printed and assembled, but I preferred to do it in wood (3 mm mdf), cut with my cnc router. It was for...

I used plaetti's Airflow Cooling Duct (https://www.thingiverse.com/thing:3376186/files) because it fits and clips on better than CarstenD's and Filboyt's Ender 3 Vent Ring (https://www.thingiverse.com/thing:2912394). However, I found the Airflow...

I'm including my PrusaSlicer 3MF file, so if you use PrusaSlicer it should be all ready to go for you. I picked up a two-pack of the cables and printed two docks/dock bottoms and a single shell so I could have a dock at work, too. It's working very...

... axis. **Happy Printing!!!** Jan 24, 2021 UPDATE: I added the Fusion 360 file for anyone that wants to modify this model. Full disclosure: I'm still a rookie at CAD, so if I've missed some obvious best practices on design, that is why. Enjoy. ...

Where the screws are going into the plastic without a nut, they will tap into the PLA plastic to make their own thread, so if the plastic used is very hard it may be best to file a slight point onto the screw tip. KNOTS: Reef Knot - for the water...

It looks like you have provided a rather long text dump, containing what appears to be the 3D modeling file information and geometry specifications for something resembling an interior space or structure. There are coordinates mentioned in there. To...

I have included STEP files if you want to modify anything. Remixes are encouraged, as I'm sure others could do better. People often like to show support to creators, and I don't have an issue with that. I'm not rich, but I'm also not broke. If...

...Printer must be capable of printing 1 single perimeter if you want to print the launcher, otherwise you should be fine as no file requires supports. PETG or ASA recommended for launcher if you intend to use CO2 as it stresses the piece quite a bit.

There might be changes to the model and files in the future. Guidance are currently work in progress, at the moment it may be messy to read. hopefully the pictures will be good enough for now.Update May 2024:Added two new 5key button panels. suitable...

Make sure the hooks face upwards. Optional: Use felt cutouts or print something from flex to cover the four hexagonal feet for protection.If anything is unclear you can reference the include .stp-file  of the whole assembly.How to use itBy...

The explodedView.stl and fullView.stl files should not be printed. The cylinder and piston must be printed horizontally to give them strength and ensure they slide with the layers, not against them. The cylinder is printed without supports, but a...

Marlin 2.0.1 configuration files from my machine are included. My machine runs RAMPS 1.6. #How to: First install the coupler on the motor. Tighten down then install the bearing in the motor mount followed by the motor and coupler. Secure with...

There is a single-part STL file for 3D printing the boat in one material, and a multi-part STL assembly to be suitable for multi-material/printhead 3D printing. Documenting the results ==================== You can use the Smartphone Photo...

Exploded views are included in the zip file as well as a build sheet. This project assumes a entry level knowledge of model rocketry and safe rocket building techniques. If this is your level 1 project, feel free to ask questions, if you are unsure....

To create those, the part V0 was exported as an STP file and the variable radius fillet details were added using MoI3D. Finally, the dumb solid was re-uploaded to Onshape as part V1. The closest workaround to the variable radius fillet problem I...

Update 26 Jul 21See this YouTube video by Nils Rasmusson ([https://www.thingiverse.com/nilsynils/designs]) for a performance comparison of this blast gate with other commercially available designs...

If you make any donation to help me keep working on my designs, as a sign of appreciation, I'll send you the fusion 360 files. UPDATE 2018-03-08 You can find an example on how to add this to an already existing chassis in here Post-Printing Build...

About the model Which files should I use? In the .zip folders, which you will have to unzip, you will find all the parts with different diameters. You will need to take a nut and a frame. *If this is the first time you print the phone holder, choose...

(http://www.thingiverse.com/thing:1304176) For the sake of space I removed the space from the Phosphate groups, and condensed the CRISPER target sequence. The CRISPER 2 file has a large cutout in it. This will help you see the DNA sequence it is...