valve index vr gun stock 3d models

How I Designed This =================== I took measurements from my Valve Index headset and drew up the model in Fusion 360. Surfaces in the model are 5mm thick, headest holder shelf is a 30 degree segment of 150 mm circle and tilted up 15 degrees,...

Fortunately, I had already purchased lenses from https://www.thingiverse.com/thing:2920352, so I decided to reuse them and remix this design for the Valve Index with a prescription holder for my 43mm Zenni lenses, which are smaller than the original...

The power plug for my Valve index was malfunctioning, requiring light pressure to establish a connection.\r\n\r\nTo resolve this issue, I designed a small jig that wraps around the plug to apply the necessary pressure.\r\n\r\nI utilized Blender to...

Valve Index Controller Charging Station Printed in two parts: The Base wich houses the cable, an on/off switch and the controllers. The Backplate, not strictly necessary but saves the controllers from accidentally knocking them over. If you want...

This is an adapter made for the Valve index to convert prescription lenses made by Lenscrafter to fit the original Oculus (Meta) quest and quest 2. The Sweet spot might be slightly off since I don't have the equipment to line it up correctly,...

This is a fresh new low poly cover for the Valve Index Headset. It's perfect when you don't want to scratch the original one, by bumping your controller into it - think about it. I created two versions: one without holes, tailored for those who get...

For white ceiling I recommend white filament, I think colored print I did looks off. How I Designed This =================== I took measurements from my Valve Index headset and drew up the model in Fusion 360. Surfaces in the model are 5mm thick,...

Prescription lens adapter for the Valve Index for those who may have previously made Oculus Rift CV1 Prescription Lens Adapter by jegstad. It's designed to take standard single vision lenses for Zenni #550021 frame. The lenses stay securely in...

### Description ### If you are looking for a Valve Index lens protector, consider printing out this model instead: https://www.thingiverse.com/thing:3733220 Prescription lens adaptor for the Valve Index. It's designed to take standard single vision...

This is a replacement bracket for your valve index controller. If you like me tried to use your controller to assist in rapid deceleration due to a gravitational anomaly you may find the top can separate from the lower grip. This is due to the two...

A simple, minimalistic base to set Valve's Index controllers on for charging and storage. The design is inspired by the model from BearCubsTeacher on thingiverse: https://www.thingiverse.com/thing:3744655 But I just wanted to use the following 90°...

This Valve Index Base Station Mount is designed to install the base station with its onion nut. The mount is designed to be fixed on a 30 mm aluminium profile (8 mm slot), but can actually be attached to any shelf or cabinet. The mount is fastened...

This is a straightforward wall mount for the Valve Index light houses. They won't fit the Vive Pro light houses, but it should be simple to adjust in the Fusion 360 file. Other Materials * Two screws to put into the wall. The screw head (+washer)...

... Hard plastic might cause damage. The index uses a torx T6 screw to attach each earpiece. Print instructionsCategory: Computer Print Settings Printer Brand: Prusa Printer: i3 MK2.5 Rafts: No Supports: No Resolution: 0.2 Infill: 100% Filament: - TPU -

I carved out a small notch on the side to accommodate your index fingers, making it easier to hold and maneuver these tools.

A quick and dirty remix to mount my Index controllers on my Ikea Skadis pegboard Just need small supports for the Skadis hooks

I stepped on the wire and stood up while playing holopoint and the back clip on my index popped right off, I couldn't find a model online so I eyeballed it in openscad

A Mounting Bracket for the Index Lighthouse. The interior measurements of this mounting bracket are 1.77 inches by 0.79 inches. ...It is designed to accommodate the standard ball and cap that comes packaged with the base station.

Remix by @kheshtar (Twitter).I couldn't find a model for a normal, plain knob for the Index strap, so I asked my boyfriend to make one, based on the Half-Life knob by Slurpy

... and added a decoration line. As USB cable I take this one: https://www.amazon.com/NetDot-Braided-Magnetic-Charging-Compatible/dp/B07M721KFZ The SDL of the Index Controller Logo can be downloaded from the original thing.

I was eager to free up some space on my workbench, so I designed a simple wall mount for my new index, and it turned out great. ...The wall mount requires 5mm holes and uses #8 screws in combination with 1/4" drywall anchors to securely attach it to the...

Remix of the Two-Hook Mount by Shellite: A DIY Attempt. ...No Access to Index Lighthouses, So Measurements Were Adapted from Provided Specs. ...First Print Attempt is Yet to Come.\r\n\r\n\r\nFeedback Appreciated - Any Issues Please Comment Below.

Remix of https://www.thingiverse.com/thing:3976286 to incorporate the https://www.thingiverse.com/thing:4113807 index controller charger instead. ... Used the softside of Velcro tape to avoid scratches Furthermore I've mounted this mount without...

This accessory is particularly useful for those who have misplaced or not received the rubber bands that come with Index Controller straps, or simply prefer a convenient alternative to visiting a hardware store for two rubber seals. Print this...

Just slide this over the top Index strap, insert cable ties into channels on the side and wrap cable like on the first image and tighten down the cable ties. I used the cable ties that came with my Prusa MK3S, the dimensions for the cable ties are:...

A compact mount designed to fit snugly within an Index's cargo compartment, also known as the frunk. Four distinct design options are available, catering to various preferences: 1. Frame: A sturdy and minimalist configuration 2. Frame without vent...

Simply slide it over the top Index strap, insert cable ties into the channels on the sides, wrap the cable as shown in the first image, and tighten down the cable ties. I utilized cable ties that came with my Prusa MK3S, which have the following...

I'm starting with the Valve made Face Gasket .stl file and making some initial edits myself. After putting it through a test, I found that while my modifications are rough around the edges, they seem to work just fine for me. If you're dealing with...

The index HMD is quite heavy, so I printed the wall mount with full infill, but that proved to be quite the overkill. Fewer perimiters and some dense infill will do the job just fine. Printed with black PLA, 0.2mm layer height. The top and bottom...

I printed the previously uploaded wide gasket: https://www.thingiverse.com/thing:3738708 I compared it to the original model provided by Valve. It looks like the previous model was simply squished in Blender. This achieves greater width, but alters...