valve index magnet mod 3d models

I made this cable guide to route the cable better when using an overhead cable management system and to allow the cable to flex over a longer section to reduce pinching. The tolerances are pretty tight so you may need to slice open the gap where...

You will have to glue the logo in if it isn't too tight. You might need to also sand the logo for it to fit. My tolerances aren't perfect yet :( Once printed you should probably put some adhesive craft foam or something to keep your headset from...

Using a ceiling cable management system can be super helpful, but be aware that the clamp can technically be installed almost anywhere. ... It snaps into place very securely, making it a tad challenging to take out without causing some damage.

ImportantPlease try the cables before printing. Display Port can be finicky and an extension cable might not work for your setup. ...For me only a very short cable of 2 meters worked.Required Hardware4 wood screws 3.5x16 for mounting on the desk (don't...

Printed, but never mounted.

The detailed three-dimensional rendering model of the Generation Two Base Station is readily accessible within the confines of the Steam Virtual Reality driver software package.

Hi I am Frezzy from Vnvisual studio. This high-quality, photo-real model is designed to elevate detail and realism in any rendering project. The fully textured, detailed design allows for close-up renders and was originally modeled in 3ds Max 2012...

An exotic stand for exotic controllers; This organic concept leverages the natural center of gravity of the knuckles to cradle them in a stable orientation with a minimalistic design. <b>Warning</b>: Hanging the knuckles on the stand is...

I wanted to create this because for me it was annoying to stop/pause the printing to change the filament (color) for the middlepart if you want multicolored. Easy to print (30-40min) in any color you wish. ...simple to install - glue it, done!

Just a simple remix. Did not like the gab that was in there (caused unneeded support). Made it a little thinner to decrease built time and overall bulk coming from the holder -- moved the center of gravity to be more near the wall. I used simple...

They sit perfectly in the groves, I made it for you guys :)

... Depot magnets, no cutting or filing necessary. Simply add a drop of glue and the magnet will slide in effortlessly. Enjoy! http://www.homedepot.com/p/MASTER-MAGNETICS-0-3-in-x-0-11-in-Neodymium-Rare-Earth-Magnet-Discs-10-per-Pack-07045HD/202526363

MAGNET MOD for Galva's Great Huna! ... Included Files: Vahi cut to fit the Great Huna Great Huna with 6.3mm x 3mm Hole for Magnets found at Michael's Crafts (Three Versions: Axle, Stud, Nothing) Great Huna with 8.4mm x 2.75mm Hole for Magnets found at...

Credit is due to Thingiverse for making available at https://www.thingiverse.com/thing:3772599 and also for the model located at https://www.thingiverse.com/thing:4270682

Requires: 2 x M5 Slide in T-nut 2 x M5 x 16mm screws 4 x 8mm diameter x 3mm thickness magnets (2 per side stacked) Just realized there are already a bunch of these on here. I just designed this because I had t-nuts handy. ...So here's another...

I made this remix cuz i was looking for magnet mod for logitech H-shfter and could not find any for free. Its not ideal, after asembly it needs some tweaks with torch and some filing due to square edges, but for now im not thinkign about making new ...

Valve Screws: M4x15 Housing Screws: PT 3x15 Valve: FPD-270A (12V DC)

A Magnet mod for the AAT (Trade Federation Battle Tank) For Star Wars Legion The Main Body is split on to so it can be printed with minimal or no supports on the peg holes, The top shim is a push fit, but also can be glues on if wanted, The plug for...

Install powerful magnets on both sides of the horizontal bar on your Ikea TUPPLUR roller blind to keep it securely in position at all times.

They're designed for 8mm*4mm circular neodymium magnets to be pressed in (untested, might fall out eventually). Version 2: The paddle is now a bit further outside and further away from the wheel, to make it easier to reach the paddles and so that...

... you want to use this Version. Magnets i used: https://www.amazon.de/-/en/gp/product/B0187MD22U/ref=ppx_od_dt_b_asin_title_s00?ie=UTF8&psc=1 Please don´t sell this print rather buy the original from Sim Racing Addict. ... Otherwise enjoy :)

So if you have the money rather buy the Sim Racing Addict version if you can. You are free to improve the model further if you like, there is still a lot of room for improvement, but it works for me right now.I purchased Ø 15 x 3 mm neodymium magnets...

This is a modified version of the original design found on https://www.thingiverse.com/thing:3147969, incorporating a 6x1.5mm magnet for added functionality. Great job on creating crashdebug, you've done an amazing thing! My modification can be...

Designed for 4pcs 8x5mm N48 Neodynium magnets and 4pcs M3x16mm bolts, 8pcs M3 washer and 4pcs M3x10 Bolts. NO SUPPORT NEEDED! ... FOR PERSONAL USE ONLY - NON COMMERCIAL - NOT FOR RESALE COPYRIGHT SRA.HU-SIM RACING ACCESSORIES - ALL RIGHTS RESERVED ...

Designed for 4pcs 8x5mm N48 Neodynium magnets and 4pcs M3x16mm bolts, 8pcs M3 washer and 4pcs M3x10 Bolts. NO SUPPORT NEEDED! ... FOR PERSONAL USE ONLY - NON COMMERCIAL - NOT FOR RESALE COPYRIGHT SRA.HU-SIM RACING ACCESSORIES - ALL RIGHTS RESERVED ...

... I did not display internal components. To understand the valve's inner workings, refer to this catalog: http://www.kitz.co.jp/english2/pdf/E-357-09.pdf or consult Wikipedia's butterfly valve page (https://en.wikipedia.org/wiki/Butterfly_valve).

Detailed 3D model replica of Valve Index VR headset with controllers and sensors

These are for Valve Index Knuckles and HTC Vive 3.0 Trackers. ... I have made two versions for flat head chargers and round head chargers (thinking about magnetic chargers for my personal use) Whatever infill is fine I would suppose, printing mine out...

These are for Valve Index Knuckles and HTC Vive 3.0 Trackers. ... I have made two versions for flat head chargers and round head chargers (thinking about magnetic chargers for my personal use) Whatever infill is fine I would suppose, printing mine out...

A spacer that increases the height of the USB C connector on the charging cable that came with the Valve Index Controllers so you can plug it in by just putting the controller in.