valve base station 3d models

Designed this holder because the original did not fit in my office. ... More discreetly, the base station sits straight but tilts forward a bit. Easy to print. ...(Print the shelf upside down)

This Valve Index Base Station Mount is designed to install the base station with its onion nut. The mount is designed to be fixed on a 30 mm aluminium profile (8 mm slot), but can actually be attached to any shelf or cabinet. The mount is fastened...

Mounts behind the base station stand of the Valve Base Stations, with bolts through the screwholes, enabling the mounting of Valve Base Stations on microphone stands.

The convenient conversion of Valve's Github repository into a quick mount for Valve Index base stations, now available in STL format.

Wall mount for Valve Index Base Station with a 45 degrees angle. ...It's designed with an equal hole spacing as the original mount.

This is a design I made being very dis-appointed with the current mounting solutions for the Valve Index Base Station v2. It uses 2x 1/4"-20 Nuts, 2x 10-32 3/4" or 1/2" long srews, and 2x 10-32 Nuts McMaster Part Numbers: 10-32 Nuts 91841A195 10-32...

I´ve bought a used Valve Index where no wall mounts where included. To get the BaseStations on the Wall i´ve just designed these Simple Wall Mount. Be careful when pulling it on as the thread can easily brake with to much power. ... Of course you...

Destiny logo themed replacement Base / Wall mount for Valve Index base stations. ... Flat bottom for "command strip" mounting on wall.

Destiny logo themed replacement Base / Wall mount for Valve Index base stations. ... Flat bottom for "command strip" mounting on wall.

... for the Valve Index wall mount. ...It is angled 30 degrees so you can point it at your space easier. You should use the stock ball mount from your base station. The thread is M20x2. ... Edit 10/10/20: Added recess to bottom for wall anchors

... Pieces connect to each other with M4x30mm bolts, except much shorter bolts should be used for connecting the base station stand to its mounting. ... Tested with 2 arm pieces - feels very sturdy and rigid, could probably go up to 3 or 4 pieces.

Changed to work with the Valve Index. ...Updated very quickly, the holes are correct but the shape doesn't line up smoothly like the original did with the Vive parts.

I´ve bought a used Valve Index where no wall mounts where included. To get the BaseStations on the Wall i´ve just designed these Simple Wall Mount. Be careful when pulling it on as the thread can easily brake with to much power. ... Of course you...

Comes with 2 models. ...The base one is 20mm thick for a shorter amount of cable and a 30mm one if you need more room.

The 3D model was created on real base. ...It’s created accurately, in real units of measurement, qualitatively and maximally close to the original.

... can point it at your space easier. You should use the stock ball mount from your base station. The thread is M20x2."You can find the original mount which faces to the right at Angled Valve Index Base Station Wall Mount by Phantom329 - Thingiverse

Each Large Command Strip is rated to 5 pounds, so it should be more than enough to hold the Base in place.Quoting the original description on Thingiverse (Angled Valve Index Base Station Wall Mount by Phantom329 - Thingiverse ):"This is a drop in...

This is a basic wall/ceiling quick mount specifically designed for the base stations of the Valve Index. Simply slide the original plate into the mount, and you're good to go. To secure it in place, use the included screws that come with the Index...

When I tried to run my Roomba in my VR room, the robot was very confused by the IR light put out by the Vive base stations. I don't like unplugging my base stations, so I made this little hood to block the IR light while vacuuming. ...Works with 1.0...

... my base stations. ...The specs for the base station 2.0 state that it has a 110 vertical FoV and a 150 horizontal FoV so using these I can hold them up to the center of the face of the base station and get a general idea of where the lasers are going.

Hi I am Frezzy from Vnvisual studio.

This adapter is specifically designed to attach the Index lighthouse mounts to the old mounting holes from the Vive mounts. The design incorporates M4x15 bolts between the Index mount and the printed part, while regular wall screws are used between...

Feed the cable into the hider from the outer perimeter circling inwards. ...You can use the thicker version if you have more cable to hide.

Once piece slot style mount for valve index base station 2.0's. these let you use command strips or some other form of adhesive mount for the base stations as apposed to screws. I recommend you print these vertically slot up. ...snug fit and allows...

Customized the original file to allow support-less printing, I also included Left and Right angled mounts. ... Once printed just clean out the hole with a knife/pliers/scalpel so you can put the screw through.

6 cm between holes. ...Made not to drill walls of a rented house.

If your monitor stand cylinder's inner diameter is 32mm, this mount will work for it. ...Just remove the cap off the top and slide the mount in.

This wall mount allows the base stations for the Valve Index to be wall mounted with 3M Command strips. It requires the ball joint from the original screw-on wall mount, and is a perfect fit. No supports required. Infill of 15% works well. ...A fine...

The Valve Index base station will attach to the mount with the original screws. WARNING heat up the OEM screw if the hole feels too tight. PLA tends to snap if the load is too high. Watch out! The screw holes on the base station mounting...

Remix of prittstift design. The idea is slight alteration to have part without unnecessary hole or sharp edge or stress concentration. ...The same kind of drawing rule used in aeronautical milling parts.