usb port covers 3d models

I would apprechiate a comment if you found it working for you!You only need to print the USB-Hub holder, but the bridge can be added to keep the USB Hub from moving around in the holder. ...The USB-Hub modell is just added for reference.I added the...

Should work with the USB 2.0 and USB 3.0 versions. Please note, that it's not a tight fit. I wedged a small piece of cardboard into one of the sided to hold it tight. If your printer is super accurate, you can measure and adapt the files. ... The...

This USB-to-UART PL2303HX module can be used in a variety of applications, including connecting to a UART interface. ...It is similar to the USB To RS232 TTL PL2303HX Serial Cable Converter Adapter Module For Arduino AU found on eBay, which has been...

... - a hole in the back. ...This particular design choice allows for an additional power connection via micro-USB, which is a common requirement for some USB hubs. ...You can find the Fusion 360 file for this project by visiting https://a360.co/2CsScBc.

INSTALL ANKER'S USB HUB IN ANY DIRECTION AND LOCATION, DESPITE ITS UPSIDE-DOWN CAPABILITY. OPTIMIZE HEAT DISSIPATION BY DIRECTING AIR FLOW TOWARDS IT RATHER THAN ALLOWING IT TO CONCENTRATE ON A SOLID SURFACE. UPGRADE THE VISUAL APPEARANCE OF YOUR...

I remixed my own thing. ...remixed, revision, yada yada. whatever. I added 7 usb holders in the front and kept a couple of the very short cable tray fingers on the sides. ...Printed in abs with my standard settings.

This is a compact housing designed specifically to accommodate an Anker USB charging device. ...Its versatile design allows it to be easily mounted beneath a work surface, providing convenient access to power when needed.

... my own creation. ... Remade, revamped, yadda yadda, whatever. I integrated 7 USB mounts at the forefront and retained a few of the extremely short cable rack extensions along the sides. ...Fabricated with ABS plastic using my default settings.

A simple remix that changes the cable hole cutout with one that fits the Panel Mount USB Micro-B Extension Cable from SparkFun

An adapter from an old charging socket (MS 75058-1) to a USB.This socket is common in M113 and more armored APCs, Humvee, tanks and not sure whats more.

Taking from https://www.thingiverse.com/thing:419284 , I added a little length, a hole for a USB cord, and a slot to get access to the SD card without opening the case.

... labs, or any area where cables tend to get tangled and cluttered. With its robust metal construction, it can support multiple USB hubs, charging stations, and other electronic accessories, ensuring that your devices stay tidy and easily accessible.

This led to discovering [LOLYsk's Gamecube-USB-C-PD-MOD](https://github.com/LOLYsk/Gamecube-USB-C-PD-MOD) on GitHub, a self-crafted USB-C solution that’s more economical and reliable compared to the commercially available mods. I couldn't find any...

This is a holder specifically designed for the Anker 71AN7105 charger, a popular five-port charging solution available on Amazon. The model features two dedicated holes that allow it to be securely fastened to the edge of a standard desk. ... Print...

Replacement housing for the front power port. This holds a disassembled version of this charger https://www.amazon.com/gp/product/B07PGT7LSR/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1. A plug and and wires will need added to the charger. I added...

These can typically be gotten on amazon for about $20 total. Optionally, you can re-solder the K5 - K8 button connectors to the backside of the board so you can connect additional buttons through the usb joystick. Take care not to short these...

Any USB arcade will work as long as it uses a typical SANWA style microswitch joystick and an Easyget button to usb board. These can typically be gotten on amazon for about $20 total. Optionally, you can re-solder the K5 - K8 button connectors to...

These connectors are flimsy - putting things around or near the cable that rest on them and put any downward pressure will bend it down and eventually destroy the USB-C connector on your computer and hence your motherboard. This little device goes...

To ensure it stays put even when USBs are plugged or unplugged, I've used a tiny bit of BluTac to hold it steady against any potential movement. The stand itself is securely attached to the cabinet using BluTac. ... Print Settings Resolution: ...

These connectors are flimsy - putting things around or near the cable that rest on them and put any downward pressure will bend it down and eventually destroy the USB-C connector on your computer and hence your motherboard. This little device goes...

Check port and network status with built in LED indicators.Data Encryption: The AnyplaceUSB software program offers password authorization and traffic encryption for data security and safety.High Speeds: Share and access 4 USB 2.0 high-speed...

Check port and network status with built in LED indicators.Data Encryption: The AnyplaceUSB software program offers password authorization and traffic encryption for data security and safety.High Speeds: Share and access 4 USB 2.0 high-speed...

... the Keycap Mesh to the body, and it's still attached. I wanted to test my slim to none 3D designing skills and adapt the MicroUSB hole to fit a USB C one, and I think I did it! ...It isn't quite the size, but it fits and that's enough for me.

Some Atari Portfolio parts which are often get lost: - Battery cover - Expansion port cover - Small (originally rubber) leg - Small plastic details near display hinge I used black ABS plastic an a lot of sanding. ...

I wanted an external USB connection for my Hiker Trailer to power some awning lighting, but no one makes what I was looking for.  This was printed with Prusament PC Blend and NinjaFlex Chinchilla.  The design is similar in appearance to...

I made this bracket so that I could secure my Anker 4-port USB hub. ... Amazon link: https://www.amazon.com/gp/product/B07L32B9C2/ref=ppx_yo_dt_b_asin_title_o08_s00?ie=UTF8&psc=1

The USB port can be easily ripped off from the PCB if you handle is less carefully than taking care of your first born child. Hence this USB port guard. There's nothing special about this print. ...It's very easy to print. When installing, loosen the...

... to 18V). ...Next the battery pin are also other connectors (S.bus, S-port, RSSI). Plug the battery voltage pin into wrong position will probably damage the receiver. There are very simple covers, which can be used to protect other (unused) pins. ...

Secure your EVOLVE GTR's USB port by covering it up to prevent unauthorized access or accidental damage. ...Use a protective cap or sleeve designed specifically for this purpose, or apply clear packing tape over the port to safeguard it from dust,...

I designed the ATN USB port cover with a threaded interface, just like the original part. At 100% print size, it fits perfectly and snugly into place. You may need to advance it back and forth a few times during installation to get it just right. I...