usb cable protector 3d models

Download  the ZIP to get all the STL files.This first release of STL for Hero Me Gen7 supports:65 3D Printer models (plus clones) 17 Hotends12 Extruders (27 mount options)12 ABLs35 Part Cooling Duct options10 Cable Management options5...

Remember the Y-axis rails are opposite hand. Use the Zip Tie Mounts and Zip Tie Holder(s) for cable management. They are not shown on the drawings. To glue Zip Tie Mounts to the drive carriages or X-axis rail use Plastruct Bondene. The Zip Tie Holder...

* Cura's support blocker can be used to avoid supports in the cable management points. * I only used supports "touching the build plate" on the regular side pieces (the electronics box side needs them everywhere). * The maximum current (all...

The same assembly provides a modular system for adding, changing or removing different features from around the hot end such as cable management, fans, bed sensors etc. While this isn't a remix, i'll give some credit to Tech2C and his hypercube...

* It's relatively hard to fix a ripped uFL as it often rips the HF pad/trace as well, so use the antenna glue to glue the antenna connector AND as much cable as possible to the VTX board. It's better to install VTX with uFL connector facing front...

https://youtu.be/y8e68emZvH8 So to give you choices and fulfill your personal preferences in 3D printing, the Hero Me Gen7.4 now supports over 115 3D Printer models (plus clones), 47 Hotends, 37 Extruders (over 45 mount options), 20 ABL Sensors (34...

The ground for the voltmeter is taken on the black cable of the power entry on the motherboard Cost 1/5Difficulty 1/5Goal : catching the hot bed when it's hot , without using the adjustement screw to pull up the hotbed front of you, and the risk to...

Default settings and not set explicit in this cfg ######################################## # basic settings ######################################## [mcu] serial: /dev/serial/by-id/usb-Klipper_stm32f407xx_220040001651383230343230-if00 [printer]...

Default settings and not set explicit in this cfg ######################################## # basic settings ######################################## [mcu] serial: /dev/serial/by-id/usb-Klipper_stm32f407xx_220040001651383230343230-if00 [printer]...

Normally there are no springs or other parts that can blow off, but the USB port and audio jack can sometimes be a little difficult to remove or reassemble. I searched on Youtube if there was a video for the dismantling but I did not find one. I...

"Right side mounting for relay, 40mm fan, and slot for Pi Camera cable" (https://www.thingiverse.com/thing:4787329); 4. "SKR 1.3 + RPI 4 Frame Without Spacer AIO Electronics Enclosure" (https://www.thingiverse.com/thing:4772953); 5. "SKR 1.3/1.4...

These pins do not come in STL files but can be made out of short pieces of regular 1.75 PLA;- Johnny 5 can be displayed with either of two left shoulder mount variants - an articulated laser weapon or a utility pack;- The utility pack can hold an...

The 3D printing model's chosen scale is 1/34 for the FFF/FDM version and 1/68 for the DLP/SLA/SLS version.VERSION SPECIFICATIONSFFF/FDM 3.0 version features:- Contains 66 parts;- A printed model is 235 mm tall, 96 mm wide, 134 mm deep;- The updated...

for board games or anything else. see the provided STLs for examples what can be created using this customizable thing. I created multiple "box-style" things on thingiverse. https://www.thingiverse.com/thing:3263783 Customizable Magnetic Screw...

The 3D printing model's chosen scale is 1/16 for the FFF/FDM version.VERSIONS SPECIFICATIONSFFF/FDM 1.0 version features:- Contains 99 parts;- When printed the model stands 416 mm tall, 213 mm wide, 919 mm deep;- Minimal recommended 3D printer build...

links)4 AAA Batteries (each 1.2 V; 800 mAh)Shrink rap (I hardly used it due to too small diameter)Solder tinBit of copper wire (Stripped ethernet cable has solid core)3 V (3mm) LED (Colour your choice; Diode fit correct +/- orientation...

The other designs are all made to be mounted on the right side of the gantry which clashes with the power cable feeding the bed thereby requiring you to rotate the bed which I did not want to do because then my strain relief adapter would not work. I...

I don't want to have any cables hanging out. My current setup uses an Arduino Nano, MPU-6050 Gyroscope/Accelerator, Step-Up (Step down on the big Geodesic), a BMS and some recycled 18650 batteries. As LEDs i use single W2812B LEDs which are soldered...

It can be mounted anywhere, and the cables can be routed directly within the holder. I illuminate my RepRap 3D printer's control panel with it. The LEDs require a 12-volt power supply which can be supplied by the printer electronics (Rumba Board). ...Il...

If you have installed the latest firmware, you have the possibility to reverse the direction of rotation of the extruder without needing to touch the wires, go to the settings, keep the button pressed for 2 seconds, a new menu appears, click on...

Make sure the power jack nut is installed as the nut cannot fit over the female spade connectors.Remove the electronics case cover.Remove the two screws holding the rear printer frame to the extrusion next to the electronics case.Insert the red and...

"Well," I said, "I've got to go up-stairs and get off some cables." "Do you really have to go?" "Yes, I've got to get these cables off." "Do you mind if I come up and sit around the office?" "No, come on up." He sat in the outer room and read the...

:-P MUCH stronger, more reliable grip on the filament. Should work fine with flexible filaments now (I haven't tried). The upper filament guide has been enlarged and replaced with a loop. The sensor mount is now an optional part that you print and...

They are all part of the Tentacle Zip Tie Kit You can use them for cable management or to attach a tentacle to something for support or balance. Two of these feature a loop that can accept multiple zip ties. The loops on these two are in different...

 The filament cables arch up as high as two feet above the desk. The depth is no more than 20 inches towards the back.The base board part that touches the table is 11 inches wide, starting 9 inches behind the printer back frame edge, and 20 deep,...