usb c female pcb 3d models

This is a basic dust cover that fits perfectly into the charge port of my Samsung S8. ...I opted for a USB-C design, as it seemed pointless to spend eight dollars on a pre-made cover when I could create one myself at such a low cost.

This is a portable keychain featuring dual USB ports - one Type A and one Type C. It's designed for carrying compact cables, such as a 30cm cable, to charge your phone using a power bank while on-the-go. ...The tight fit of the holes ensures that the...

I protected the USB-C charging cable for the 2017 MacBooks, which charge via Thunderbolt 3, by remixing it. ...I then created a newer version that's slimmer in design, ensuring it won't obstruct the adjacent port being used for charging.

I didn't like the gap between the USB C and the case, so I made this. It fits really well, so I decided to upload it here. ... I made this with Catia, feel free to remix it as you want.

Gasket for modifying electronics with USB-C ports, since cutting a precise slot by hand is HARD.Use the provided template to mark where to cut a rough slot for the gasket.Glue the gasket in.Admire your shoddy work. 

https://www.thingiverse.com/thing:2822140 I had bought a few pro-micros off eBay that were USB-C instead of micro-usb, and they were slightly offset from center, meaning the original stream cheap didn't fit. This is slightly different, with 5x2...

... can carry around on a keychain and plug into your smartphone when you need it. Please note that the hook is designed exclusively for a lying smartphone or other lying device with USB C port. ... **Update 18.04.2021:** Taper removed at the eyelet.

This is a cap/cover for a USB-C charging port to keep dust and debris out. There are two versions included. The taller version is shown in the picture, and a shorter version that wont protrude as much is included as well. Print with the large flat...

This is a cap/cover for a USB-C charging port to keep dust and debris out. There are two versions included. The taller version is shown in the picture, and a shorter version that wont protrude as much is included as well. Print with the large flat...

I have a USB-c dock that I have an extension cord for to be able to easily move the dock between computers. However the connction between the cord and the dock was a bit shaky so I remixed this to be an extension holder. ...The whole on he side is a bit...

I own a Nexus 5X and the original USB C charging cable has become worn out from extensive use, resulting in visible tears. To replace it, I decided to design and print my own custom cable, but unfortunately, I couldn't find an exact match online.

I used an Aukey cable (available on Amazon: https://www.amazon.com/AUKEY-Braided-Charge-Samsung-Galaxy/dp/B01B634WNK/ref=sr_1_1?ie=UTF8&qid=1541082207&sr=8-1&keywords=anker+usb+c+cable&refinements=p_89%3AAUKEY) for the cable. Make sure to use enough...

 Every time I looked at that USB-C cable hanging out there, I worried I was going to set a drink down on it, or put my feet on it, or some such, and snap it off the laptop's motherboard.I made a little “kickstand” to hold it up.  This fits...

This is a simple USB-C Charging stand. I created it for charging my VAPE's. I have also included a version without VAPE on it if you want to use it for phone charging. ... The cables I used for measurement were Amazon Basics -...

Just a type C port.

... The two-piece version requires removing the Female USB connector and soldering directly to the pins. I plan to use one of these in my ATX power supply that supplies 2 Amps of power. To secure the panel of your choice, use four 3mm screws and nuts.

... and it has a bandwidth up to 18 GHz. ...It is cut such that it can be used for a PCB thickness of 0.031" For more information : https://www.svmicrowave.com/parts/sma-female-pcb-edge-launch-connector-031-pcb-thickness/2985-6037For more information :

... and it has a bandwidth up to 18 GHz. ...It is cut such that it can be used for a PCB thickness of 0.031" For more information : https://www.svmicrowave.com/parts/sma-female-pcb-edge-launch-connector-031-pcb-thickness/2985-6037For more information :

It is cut such that it can be used for a PCB thickness of 0.063" Note : Drawing chart of part numbers does not reflect title description ; but is close !For more information :...

... Microwave p/n : 2985-6038 and it has a bandwidth up to 18 GHz. ...It is cut such that it can be used for a PCB thickness of 0.093" For more information : https://www.svmicrowave.com/parts/sma-female-pcb-edge-launch-connector-093-pcb-thickness/2985-6038

It is cut such that it can be used for a PCB thickness of 0.063" Note : Drawing chart of part numbers does not reflect title description ; but is close !For more information :...

... Microwave p/n : 2985-6036 and it has a bandwidth up to 18 GHz. ...It is cut such that it can be used for a PCB thickness of 0.042" For more information : https://www.svmicrowave.com/parts/sma-female-pcb-edge-launch-connector-042-pcb-thickness/2985-6036

... Microwave p/n : 2985-6038 and it has a bandwidth up to 18 GHz. ...It is cut such that it can be used for a PCB thickness of 0.093" For more information : https://www.svmicrowave.com/parts/sma-female-pcb-edge-launch-connector-093-pcb-thickness/2985-6038

... Microwave p/n : 2985-6036 and it has a bandwidth up to 18 GHz. ...It is cut such that it can be used for a PCB thickness of 0.042" For more information : https://www.svmicrowave.com/parts/sma-female-pcb-edge-launch-connector-042-pcb-thickness/2985-6036

USB_type_C_24p_maleUSB_type_C_14P_Female

I don't know the model of phone case, but it looks like a clone of this one: https://www.ebay.com.au/i/172953444925?chn=ps This stand should work for many USB-C phones as there are no edges and a healthy space behind the USB port (3.5mm, I think). ...

This is a keychain with holes for a USB type A and a USB type C port. It's useful for transporting small cables (I use it with a 30cm cable) to charge your phone with a powerbank on the go.<br/> The holes have a tight fit, so the cable will not...

This keychain comes equipped with pre-drilled holes for seamless attachment of both USB Type A and USB Type C ports. Its compact design makes it an ideal accessory for conveniently carrying small cables while keeping your phone powered up on the go.

This is a collapsible phone stand designed around a USB C hub. The hub is inserted into the base, then the lid glued in place over the top. The hub can be oriented so that the cable comes out of the left side or the right...

... as to which one is set to portrait and which one is set to landscape, which can be frustrating. So I brought my calipers to work, measured the USB-C to DisplayPort cables that were provided, and created something using OpenSCAD to simplify my life.