usb c breakout board 3d models
204259 3d models found related to usb c breakout board.
prusaprinters
A mount to fit an SKR 1.3 & 1.4 into a Printrbot Metal Plus, this mount fixes to the Printrboard holes and allow an SKR 1.3 & 1.4 to be fixed on top. with the added Z axis breakout board support.
grabcad
The Swellder Db25 D-sub Female Plug 25-pin Port 2 Row Terminal Breakout PCB Board is a high-quality connector. It's compatible with the Marcus connectors, including DB9, DB15, and DB37. Notably, it features a female Db25 connector with centered bolt...
thingiverse
Customized version of https://www.thingiverse.com/thing:4659073 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4659073
thingiverse
#### Parts used: * Simple 4-pin USB-C breakout (the one I used on [AliExpress](https://de.aliexpress.com/item/1005001446500637.html?spm=a2g0s.9042311.0.0.27424c4dAuZHzp)) * 5-pin PH 2mm connector (on...
thingiverse
Case for tamarin-cable https://github.com/tihmstar/tamarin-firmware I had a few of these (https://de.aliexpress.com/item/4000026719770.html) USB-C passthrough breakout boards lying around, so i cut one in half and used the USB-C female end.
prusaprinters
There are two end caps that fit snugly over the ends to secure the whole thing in place.Note: This was tested for fit with the HCDC 24/20-pin ATX DC Power Supply Breakout Board Module and the Electronics-Salon 24/20-pin ATX DC Power Supply Breakout...
thingiverse
Hatchbox Yellow PLA .2 layer height 220 first layer / 200 after 60 bed Brim + Gluestick Assembly: I removed the terminal block from the breakout board as this box would have been even bigger if I kept it, and soldered on my cable. I was able to...
grabcad
Ultra mini USB Type C Charger Module DC 5V 1A Charging Board for 1S 4.2V 18650 Lithium Li-on Battery Protection Board.
grabcad
DescriptionER-TFTM035-6 is 320x480 dots 3.5" color tft lcd module display with ILI9488 controller and breakout board,superior display quality,super wide viewing angle and easily controlled by MCU such as 8051, PIC, AVR, ARDUINO,ARM and Raspberry...
thingiverse
Third part of my custom mod to match the MK3's extruder on the CR-10S Pro.\r\nFind my MK3s adapter here: https://www.thingiverse.com/thing:4151703\r\n\r\nI reorganized the breakout board for easier access, securing it with a hinged door for...
prusaprinters
Required hardware:8x 1.7x4 self tapping counter sunk screws1x Adafruit USB-C breakout2x Pogo Pins 2mm2x cube magnet 5x5x5mmsome silicon cableAssembly Instructions:Put the magnets on the back of your watch to make sure you got them oriented the right...
prusaprinters
Third part of my Crusa mod to go with the MK3s extruder on the Cr10s Pro. Find my Mk3s adapter here: https://www.thingiverse.com/thing:4151703 I rearranged the breakout board for easier access, with a hinged door for protection. In the same time I...
thingiverse
A Din Rail mount for an Adafruit PMSA003I Air Quality Breakout. The holes are taped for a M2.5. ...The sensor can be found at:https://www.adafruit.com/product/4632You will need to print one tab for this design.They can be found at:...
thingiverse
Completely original, except with USB-C instead of micro USB