us 8 60w rack mount 3d models

This is a Remix of the Ubiquiti USG part from the original for the 8 Port POE Switch of Ubiquiti. Printing in PETG should be better because the switch gets very warm. This is still in Project, i did not print it yet. Maybe you can comment if it...

The original 1/2 19in rack mount I found held a Unifi US-8 and there was a matching 1/2 19in blank mount to round out to the full 19in. The middle connection point is sturdy and the Unifi model was spot on. My initial test print came out great so I...

The original 1/2 19in rack mount I found held a Unifi US-8 and there was a matching 1/2 19in blank mount to round out to the full 19in. The middle connection point is sturdy and the Unifi model was spot on. My initial test print came out great so I...

I really liked the mount from user @kbiel (https://www.thingiverse.com/thing:3208663/) but wanted something that is printable without supports. My remix prints fine on an Ultimaker 2 without supports. ...The only critical part is the bridging over the...

Shelf for holding a Unifi us-8-60w switch in a mini server rack. Top is recessed a little to allow for viewing the status lights. ... Designed to fit into this mini rack: https://www.thingiverse.com/thing:4612800

... To ensure a perfect fit, remove the rubber feet from the switch first. Updates: * I updated the design for triplex fan cooling. * I added a wall mount that works with double-sided tape. ... What can I improve or what would you like to see?

I needed a single, custom piece for my Unifi Switch 8 60W, which only came with mounts for 19" racks. To solve this problem, I designed and built one from scratch using Sketchup. For easy installation, you can simply attach the switch to this mount...

Vertical mounting plate for unifi switch on Anthro standing desk. ...Any desk can really be used, there is ~3mm slot for hanging on metal openings.

It enables me to mount the switch with precision, allowing me to clearly mark exactly where I want to place the mounting holes as I visualize the switch's final position. I'm looking forward to using it! ...Another template for UniFi USG is already in...

Unfi Switch US-8-60W rackmount for 19 inch wide rack. No supports needed. You will need (2) M3 x 10 bolt to mount the switch and (4) M4 x 10 to connect to the blank bracket. Check out my other rackmount for Unifi Secure Gateway that is...

Mounting a US-8-60W Ubiquiti Switch: A Step-by-Step Guide to Secure Screws Placement To ensure a secure and stable installation of your US-8-60W Ubiquiti switch, it's essential to identify the correct screw placement locations. Below is a detailed...

Unifi US-8 1U 10" Rack mount.Printed i PET-G.You will need a M5 screw for the hole in the back

I whipped this up in Fusion 360 to be able to rack mount my US-8-150W in to my network rack. I know there are some models out there already but I wanted the practice.</p><p>Over time, the switch does sag but not too much. I do recommend putting...

This section aligns with the design found on Thingiverse, specifically at https://www.thingiverse.com/thing:2788976. To refine this part, two key modifications were made. Firstly, any unnecessary holes were eliminated to optimize the overall...

I was thrilled by the design from user @kbiel (https://www.thingiverse.com/thing:3208663/) but needed something printable directly, without relying on supports. My remix prints flawlessly on an Ultimaker 2, sans any support structures. ...The only...

19" rack mount for Unifi US8-60W. I made this for my Creality CR6SE therefore I can't print the whole thing. I designed this in 3 parts. I used 35% infill with 2x infill line multiplier for greater strength. ... I used M4x16 screws to assemble it.

19" mounting bracket for Ubiquiti 8p 60w switch combined with Security Gateway. Print the bracket mirrored or normal to mount it one side, or print just the middle part and then mirror it. To assemble, attach two M3x10 nuts to secure the USG to the...

I designed a simple wall mount for the Unify Switch 8 60w. ... It is simply glued to a wall or furniture with double sided tape on the corners.

10 inch rack mount for UniFi US-8-150W. Required 2 pcs. ...square nuts rack.

Original Design: @kbiel (https://www.thingiverse.com/thing:3208663/)During this last heat wave in California, my little USW-8-60W switches were overheating and rebooting. &nbsp;So I added fans to this mount.It supports the installation of 2 40mmx10mm...

A standard 10-inch rack-mount unit is required to accommodate the UniFi US-8-150W, and this necessitates the use of two square nuts that are specifically designed for rack mounting purposes.

Low Profile Mounting Bracket With Dual 40mm Fan Duct for Ubiquiti Switch US-8-60W

Low Profile Mounting Bracket With Dual 40mm Fan for Ubiquiti Switch US-8-60W

USG Rack Standard Version: https://www.thingiverse.com/thing:3364732 USG Rack Standard Version with 80mm Fan: https://www.thingiverse.com/thing:3554571 USG Rack Cloudkey GEN2 Version: https://www.thingiverse.com/thing:3554985 USG Rack Cloudkey GEN2...

This one stands out as being significantly stronger, resulting in a more substantial and stable mount overall.

Stand for Ubiquiti UniFi Switch 8 - US-8-60W. This allows the cables to be passed under the switch. ... Option: some hot glue to fix the stand under the metal case of the Switch makes it easier to organize all cables.

Rack mount ears for Unifi 16 port POE switch.

Rack for: Ubiquiti Unifi Cloud Key GEN2 version Ubiquiti UniFi Switch (8-port, 60W PoE) Ubiquiti UniFi Security Gateway Including space for an 80mm fan to cool the components If some adjustments are necessary, just contact me! ----------------- ...

Rack for: - Ubiquiti Unifi Cloud Key - Ubiquiti UniFi Switch (8-port, 60W PoE) - Ubiquiti UniFi Security Gateway Including space for an 80mm fan to cool down components. If some adjustments are necessary, just contact me! ----------------- You're...