uplift desk headphone hook 3d models

I remodeled this headphone hook based on hsoj's print, increasing the width of the hook to allow for wider band headphones, like the Apple Airpods Max. I also increased the hole size on the hook so I could use my cordless drill with a bit extender.

The IKEA Bekant desk headphone mount clamps directly to the tabletop with ease. It offers a spacious 20mm area for your headphones. ...Additionally, I have created two other versions suitable for different tabletop thicknesses: * 17mm for the original...

I spaced the hanger portion for my sennheiser hd4.40 so it may be a little thinner than some headphones. I am able to slide this on my desk and it is a very snug fit, no danger the hanger falling off. The shadow on the photo is a little deceiving,...

... asked to spin text for you. ... Instructions Create with the following customizer options: Set hook height to 30 Design width at 20 Eliminate the jack by setting it to 0 Elevate the desk height to 35 Solidify the thickness at 5 Carve out a depth of 50

Individuals frequently grasp a single set of headphones with an extended cord or two separate sets without.

Fast and convenient headphone holder clip for Ikea PAHL workspace organizer. Print flat, without unnecessary support or rafting. ...Glides smoothly into place with little resistance; attach a small strip of adhesive to the interior for a snug fit.

... preventing any scratching of the table upon insertion and allowing for slight printer misalignment adjustments. I've incorporated small IKEA FIXA stick-on floor protectors to increase pressure and keep it securely in place without damaging the desk.

80% infill in PETG worked really well. this model is for a 33mm desk and I can adjust the height to accommodate desk thickness.lay flat on the left side to print

the stock bracket allows for a desk up to 40mm this bracket should work for up to 49mm thick desks. print solid. only other things needed: 1- 8mm hex nut dimensions of 12.8mm(side to side) x14.5mm(corner to corner) and 6.3mm thick ...

So I remixed it to have a longer top clamp part.For my desk, the 22mm fit best (the 15mm was too narrow and the bottom clamp part didn't even touch the desk for most part). I went ahead and extended the top clamp part for both the 22mm and 15mm...

...  Two M8 x 15mm bolts are required for attachment, easily found at any hardware or big-box store if you don't have spares from your desk assembly.Mine is a Flea Koa Concert size and does not touch the ground at the lowest setting on my Uplift desk.

 Two M8 x 15mm bolts are required for attachment, easily found at any hardware or big-box store if you don't have spares from your desk assembly.Mine is a Flea Koa Concert size and does not touch the ground at the lowest setting on my Uplift...

This custom-made under-desk headphone hook is specifically designed to fit the Fully Jarvis standing desk. It boasts a curved design that securely holds headphones, along with a smaller hook on the opposite side to manage cables. The innovative...

... importantly off the floor). To mount: You'll remove the "Uplift Desk" name tag on the left/right side of the desk. Then use 2x M4 bolts and nuts to attach. Print with whatever settings you think you need. ...I used: .32 layer height 25% infill

... importantly off the floor). To mount: You'll remove the "Uplift Desk" name tag on the left/right side of the desk. Then use 2x M4 bolts and nuts to attach. Print with whatever settings you think you need. ...I used: .32 layer height 25% infill

I remixed this from TORO's design to fit my uplift desk.  Printed in Matterhackers purple PETG at 0.2 mm layer height with supports for the little clips using SuperSlicer. Note: Make sure you've got good overhang settings tuned for the bottom of the...

Uplift Desk Motion-X Board StandThe Motion-X Board is one of the accessories for the Uplift Desk; it's designed to help people engage more motion while standing at their standing desks. The board works best on flat surfaces like tile; on carpet...

Use this bracket to mount a power strip or other accessories to the underside of your Uplift desk.  It can be mounted to the desk frame crossbar's threaded holes with M8 x 10mm cap screws.The difference between the -1 and -2 models is the...

This hook is specifically designed for IKEA glasholm tabletops, with their 9mm thick glass desktop in mind. To be precise, the glass thickness is actually around 8.5mm, but I've added a thin piece of rubber to prevent slipping issues. ...It's proven to...

A simple adaption to allow for hanging your headset or other bags etc under a shelving pine desk.

With the 4 leg desk, there doesn't leave much room left to mount drawers to the desk, unless you want them to drop pretty low due to the cross beams the desktop sits on. To give me some drawers for smaller, frequently accessed items I created some...

Headphone hook for desk

Under-desk headphone hook.

<p>Adaptation of Guym's idea. Designed from ground up using fusion 360. ...Prints without supports in two parts.</p> <h3>Print instructions</h3><p>Printed in Petg but Pla would do fine.</p>

This is an attempted recreation of RangaTang's design to accommodate larger headbands and an elongated screw hole for more compatibility. ...Printer will need to be able to bridge the bottom cutout.

Human-made modifications of http://www.thingiverse.com/thing:44705\nGenerated using Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=44705\n\n \n \n Instructions for Usage\nSelecting...

http://www.thingiverse.com/apps/customizer/run?thing_id=1245989 Instructions Using the following options: width is set to 20 desk_height is adjusted to 15 thickness is specified at 4 jack size is established at 10 hook_height is determined to be 35...

My own versions of clamps for the Modesty Mesh for the UPLIFT Desks. Print for personal use. No Commercial printing allowed. Contact me for commercial printing usage. Thanks. v2.0: Remove teeth/bumps, tighter fit, stronger infill, thicker upper...

Simple headphone hook for desk. ...:)