unr2 0 3d models
556811 3d models found related to unr2 0.
grabcad
The Decauville Locomotive, an evolved version of my initial GrabCAD model, features three driving wheel axles, categorizing it as 0-3-0. ...Powered by steam generated from a propane burner, this remarkable locomotive exhibits exceptional craftsmanship...
thingiverse
For this unique design, parameters included a twist of 1, a tolerance of 0.25, five planets, and approximately nine teeth on the sun. ...The gear specifications are: a width of 4.0, 45 pitches (P), 10 teeth (T), 51.7 diameter (D), and seven teeth on...
cults3d
Nozzle tray for a couple of nozzles on request. ... I've made 2 versions: With hole Ø5 for a M6 tap (thread) With hole Ø6.2 There is room for: 3x 0.2 Nozzle 3x 0.3 Nozzle 12x 0.4 Nozzle 3x 0.5 Nozzle 3x 0.6 Nozzle 3x 0.8 Nozzle
thingiverse
Nozzle tray for a couple of nozzles on request. ... I've made 2 versions: With hole Ø5 for a M6 tap (thread) With hole Ø6.2 There is room for: 3x 0.2 Nozzle 3x 0.3 Nozzle 12x 0.4 Nozzle 3x 0.5 Nozzle 3x 0.6 Nozzle 3x 0.8 Nozzle
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=16627 Instructions Using the following settings: additional_tooth_depth is set to 0.1 pulley_b_dia is set at 35 retainer is turned on pulley_b_ht is set to 12 additional_tooth_width is set to...
thingiverse
... ...To achieve this, specifications such as a twist of 1, tolerance of 0.4, 5 planets, approximately 9 teeth on the sun, a width of 4, pressure angle of 45 degrees, 10 teeth on each planet and a diameter of 51.7 were implemented.
thingiverse
Customized version of https://www.thingiverse.com/thing:1926136 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1926136
cults3d
Nozzle tray for a couple of nozzles on request. ... I've made 2 versions: With hole Ø5 for a M6 tap (thread) With hole Ø6.2 There is room for: 3x 0.2 Nozzle 3x 0.3 Nozzle 15x 0.4 Nozzle 3x 0.5 Nozzle 3x 0.6 Nozzle
thingiverse
Nozzle tray for a couple of nozzles on request. ... I've made 2 versions: With hole Ø5 for a M6 tap (thread) With hole Ø6.2 There is room for: 3x 0.2 Nozzle 3x 0.3 Nozzle 15x 0.4 Nozzle 3x 0.5 Nozzle 3x 0.6 Nozzle
thingiverse
The holder secures the nozzle in place. ... Print using a 0.2 millimeter nozzle tip. Layer thickness is set at 0.1 millimeters.
cults3d
It holds (in my case): 3x 0.2 Nozzle (brass) 3x 0.3 Nozzle (brass) 15x 0.4 Nozzle (brass) 3x 0.5 Nozzle (brass) 3x 0.6 Nozzle (brass) 3x 0.4 Nozzle (Tungsten) I've made 2 versions: With hole Ø5 for a M6 tap (thread) With hole Ø6.4 If there is...
thingiverse
It holds (in my case): 3x 0.2 Nozzle (brass) 3x 0.3 Nozzle (brass) 15x 0.4 Nozzle (brass) 3x 0.5 Nozzle (brass) 3x 0.6 Nozzle (brass) 3x 0.4 Nozzle (Tungsten) I've made 2 versions: With hole Ø5 for a M6 tap (thread) With hole Ø6.4 If there is...
prusaprinters
These files are in STL format.ORIGINAL POSTAccuracy of retraction distance change is guaranteed for 0.40mm Nozzle diameter.For every retraction calibration tower (based on layer height), there will be an accompanying must-read ReadMe text file (Layer...
thingiverse
... stack. For printing, you will need to use a layer height of 0.12mm or smaller. ... Keep in mind, that you need a print bed that you can easily remove very thin prints from; as the thinner gauges will be difficult to remove without mangling them.
grabcad
Ball bearing measuring 0.25 inches by 0.625 inches by 0.196 inches.
thingiverse
Als Insekten- und Auslaufschutz für 0,5 & 0,33 & 0,25 Liter Getränkedosen.
prusaprinters
Držák Trysek 0,1 / 0,2 / 0,25 / 0,3 / 0,4 / 0,5 / 0,6 / 0,8 / 1,0Nozzle Holders 0,1 / 0,2 / 0,25 / 0,3 / 0,4 / 0,5 / 0,6 / 0,8 / 1,0
prusaprinters
Držák Trysek 0,1 / 0,2 / 0,25 / 0,3 / 0,4 / 0,5 / 0,6 / 0,8 / 1,0Nozzle Holders 0,1 / 0,2 / 0,25 / 0,3 / 0,4 / 0,5 / 0,6 / 0,8 / 1,0
cults3d
... of 0.15 millimeters is established as the benchmark for quality control. The standard deviation from this mark is set at a maximum of 0.2 millimeters. The most stringent level of precision is achieved with a tolerance of 0.25 millimeters.
grabcad
... and 0.6 millimeters in width. ...This tiny device features an incredibly small height of just 0.45 millimeters, making it ideal for use in compact electronic systems. ...Its 0.65mm-pitch allows for efficient soldering and connection to circuit boards.
thingiverse
I purchased the 0.25 and 0.6 mm E3D v6 nozzles to complement my existing 0.4 mm nozzle. ... Customized version of a design found on https://www.thingiverse.com/thing:1283017 This creation was made using the Customizer app, available at...
thingiverse
I got tired of just leaving my extra nozzles lying around in little plastic bags scattered throughout my drawer, so I created this box to store and keep track of my most frequently used nozzle sizes right where I need them.\r\n\r\nThere's space for...