universal tripod mount 3d models

This is a sturdy tripod mount designed to hold firm at 43X43mm in size. To assemble it successfully, pause the print process right before completion and carefully insert the rubber band. ...Print Settings Printer Brand RepRap Printer Tricolor Mendel...

This is my first design. ...Been carrying this tripod around for 10 years. Figured this would be a good first project. Its a Optex T465 I used FreeCAD. I probably should add a pin on top so the camera doesnt spin on the mount

... damage to the surrounding area. As the glue dries, carefully remove the top piece to prevent it from getting stuck in place. When everything is completely dry, thread the parts back together using the screw and enjoy your brand new tripod mount.

Galaxy S4 Tripod Mount Design Settings Print Printer: Velleman K8200 Rafts Unnecessary Supports Ignored Resolution Set to 0.02 Infill Fully Solid at 100% Notes on Assembly: Design enables use of either a 1/4" x 3/4" hex bolt or a 6MM x 20MM hex bolt...

Adapter for enabling to mount camera (m6 screw) to a bosch tripod intended for leveleing meters etc. intended for 12mm screw, but you can file it down. also add a foam pad on the chamfered straight side to soften the tightening. Solidworks file...

M6 nut necessary for mounting on a tripod. I drew inspiration from mchasephoto's design, which is a clever way to integrate a nut. My objective was to create it with smoother (more rounded) shapes and center the slots for the GoPro. ...Please share...

This is a tripod mount that will fit most smartphone sizes. ...The particularity of this model, apart from its aesthetic appearance, is the mechanical properties of its helical body keeping the top clamp in its axis and leveled according to the...

Target Station, Stability Platform. ...Simply insert an 18 x 18 x 1/4 inch cardboard panel into the holding device for rapid target deployment. A 1/4-20 threaded adapter is positioned upside down to secure the tripod mounting system in place.

This little clip on mount will connect your GoPro directly on to a standard ¼" thread for a tripod or similar supporting device.When the model has built you will need to tap the hole to ¼ inch at 20 tpi. ...This gives a better result than trying to...

... rest/pig saddle. ...Mounts to standard camera tripod. The pins can be 3D printed but using a 1/4" steel pin would allow for smoother motion. The screw is a standard 1/4-20 thread. ...The traveling side of the vise is designed to receive a thread insert

... away from the camera's hot shoe to accommodate a teleprompter. ...To free up space, I created a custom clip that attaches directly to my tripod, positioning itself snugly underneath the camera - and conveniently features a built-in hot shoe mount.

This is a GoPro compatible tripod mount. Print instructionsTo assemble you will need an M5 nut a 1/4" UNC brass threaded insert Warm up the threaded insert with a soldering iron and push into its place.

This tripod mount accommodates most smartphone dimensions with ease. ...Its standout feature lies not only in its sleek design but also in the mechanical prowess of its spiral body, which keeps the upper clamp firmly aligned along its central axis and...

Create a tripod mount for your iPhone using Sketchup, based on Apple's dimensions. It accommodates both iPhone 3G and 3GS models. To assemble, print the design found in the attached zip file, then insert a 1/4" tee nut into the bottom hole. ...Note that...

This is a shoe mount adaptor for my Focal tripod. I initially thought I had obtained it from Thingiverse, but I also have the OpenSCAD file, which indicates that I probably created it myself. Thus, here it is. ...To attach your camera, you'll require a...

I've tested it with: * ELP-USBFHD01M-XXX "Full 1080P" (OV2710 sensor) * ELP-USB100W03M-XXX "720P" (OV9712 sensor) Note that the blue painter's tape in the photos is just there to protect against shorting out against metal bits before I made this...

This is a small but clever adapter I designed to mount two IKEA Frekvens, or rather, their LED Matrixes on a tripod. This adapter replaces one of the included connectors and allows you to screw it onto standard 1/4" threads commonly found on tripods...

This is an easy-to-assemble smartphone tripod mount that should be compatible with most devices. Here are the steps to follow: print out the required parts, heat up an M8 bolt, insert it into the turn wheel for a snug fit, cool it down by adding...

This is a simple tripod mount using the apple MagSafe charger to hold your iPhone. Uses the standard ¼" 20tpi bolt that are on tripods.Included the scad file for easy modifications. &nbsp;Thanks to Dan Kirshner - <a...

... Air 2 with a full smart case. The maximum thickness is 11.5mm. The tripod mounting plate attaches with a 1/4-20 screw and hex nut. ... I printed this with supports and used PETG because I plan to keep this in my car and didn't want it to warp.

This is a support to mount the famous Ricorée Wi-Fi antenna on a tripod. After printing, it requires a nut compatible with the camera tripod format, which apparently measures 1/4-20. However, I couldn't verify this since I found the nut I'm using in...

This is a sturdy tripod mount designed specifically for securing a dartboard in place. To ensure a precise fit, the tripod's outer diameter must be approximately 35.2 millimeters. The holder features a press-fit design, which requires an inner...

I made a remix of u/wizar's "Quick and Dirty iPhone 6 Tripod Mount," which was originally based on u/MakerCultureTutorial's "Quick & Dirty iPhone6 Plus Tripod Holder - no hardware needed." Many people said the original design was too wide for their...

... the dimensions to ensure proper sizing. The .skp files are included for easy editing or remixing. Depending on your tripod, you may need a longer bolt - my cheapo tripod's bolt is too short, but a trip to the hardware store can fix that easily.

A strategically placed hole at the bottom accommodates the tripod screw, while another in the back securely fastens a tripod-sized nut measuring precisely 12mm across, 6mm thick with a reliable 1/4-20 thread. ...Rubber bands tucked snugly into two...

[Check it out on PrusaPrinters](https://www.prusaprinters.org/prints/63151-tripod-phone-mount) ##Print instructions - Recommended 0.2mm layer height. - All parts should be printed in the default orientation for best results. - It is recommended to...

I remixed these as the nuts were always being pulled out when the GoPro tripod screw was torqued.\nThese mounts allow use of standard and lock-nuts and the nuts won't slip when tightened. Marked as W.I.P. since I haven't tested the STD Nut adapter...

... .skp files for easier editing/remixing. Depending on your tripod, a longer bolt may be required. Sadly, the bolt on my cheapo tripod is too short but its nothing that can't be fixed with a quick trip to the hardware store (or a parts bin of mine!)

The pink part snaps in and out of the yellow/orange part (See 4th photo) so that you can quickly put the phone on the mount and remove it without unthreading the tripod screw. Print instructionsI print this in PLA with 0.3mm layers, but thinner...

This mounting plate is designed to attach to a tripod, providing a sturdy base for a 3" Lazy Susan bearing that can rotate freely in every direction, offering full 360° motion. Please note: this is not a standard 1/4" tripod screw mount; it's an M14...