unifi usg rack mount 3d models

Rack mount 1U enclosure may used for some electronic equipment. ...Used 1.5 mm sheet metal.According IEC60297 or ГОСТ 28601.1-90

I wanted a simple rack mount for my OBI202. ... The device fits snugly and well into this holder so the ports face outwards.

Rack mount 1U enclosure may used for some electronic equipment. ...Used 1.5 mm sheet metal.According IEC60297 or ГОСТ 28601.1-90

Mount to attach a Yakima PowderHound ski rack to a Yakima Whispbar or Yakima Flushbar. I used a little foam door seal between the bar and the mount, but you probably can just mount it directly. ... I printed with PETG.

... the position of the rack, only the central 450mm is available for equipment. The sizes correspond exactly to the 19” rack mount specifications, and have been tested in commercially available racks. ... Instructions Cut with laser Bolt into rack

... has the disadvantage of not having a front anchor point. This bracket is designed to fit to the rear mudguard mounting hole and extend an anchor point to the rack. ...I designed this to fit a battery on an ebike kit with a rear suspension MTB

... I extended the back of each rack for added support. With just a few standard drywall screws, they mounted solidly in place. These shelves should hold their own weight without issue - the racks will likely give out before the mounting hardware does.

This is a simple hook that I designed to hang two of my laundry racks to the side of my storage rack when they aren't in use. The hook can be mounted parallel to the side or the adapter can be used to mount it from the bottom. To use the adapter...

Users seek secure and organized mounting solutions for their Power Distribution Units (PDUs) and other equipment within server racks. To achieve this, specialized button-style mounting hardware is designed for wall attachment. ...This hardware...

Standard Planet Mount STL file available for download. ...This design serves as a standard deep mount, measuring 1.5 centimeters deeper than the standard version to accommodate optical connectors that may be obstructed by the rack door.

Mounting my Raspberry Pi, which runs OpenHAB, to the side of my compact wall-mounted rack was a priority. ...I wanted the Z-Wave USB stick positioned for maximum signal strength and optimal reception.

Designed to mount to 1U of a standard network rack. Allows you to easily use the controller to control rack fans or other devices inside of a rack or enclosure. Print face-down. No supports are required. The STC-1000 isn't very heavy, so not much...

Hi, this is my take on a Rasbery PI server rack mounting case. Its designed to print without supports and fit most versions of PI. This one was deigned with the PI 3 and Le Potato in mind. The lid is a press fit and can currently on fir on the RH...

A remix of https://www.thingiverse.com/thing:3690500 and similar to my https://www.thingiverse.com/thing:4326937 This is a 19 inch rack mount for a quantity of 22 keystone devices. The rack is divided into 2 halves for easier printing. ...Strain reliefs...

This is a 19 inch rack mount for a quantity of 22 keystone devices. The rack is divided into 2 halves for easier printing. ...Strain reliefs are provided at each keystone location.This is a remix of:https://www.thingiverse.com/thing:3690500

I have a bicycle tail light that I couldn't mount to the usual seat post or seat mount because of a tail bag, so I made this to mount under the rear rack. It uses the hardware that came with the light (Cute Eye) to mount to a seat post. ... The holes...

A cable management system consisting of a wall-mounted rack designed to organize and store various cables ranging from 5 to 10 millimeters in diameter, each equipped with distinct connectors.

Phone mount designed to securely attach to a weight rack, requires minimal effort to install but may experience excessive friction due to slight imperfections in its design, a light sanding would significantly improve overall performance and user...

Quick and dirty ghetto Raspberry pi mount for switching racks. ...I use these for cheap nut servers for non networked APC UPS Have tested it on RPI 2/3 fits a 1ru uses 3mm screws for rpi

This is rack mount system for Hikvision NVR Print with PETG or ABS. Simple print with supports. ... My NVR model is DS-7608NI but other are same sizes, check with producer.

Needed to mount drives in my new 10'' rack server case…. ...so far it holds.</p><p>Suitable for 3.5'' SATA drives with joined power and data extension cable (hot glued into the hole).</p>

Did a phone mount that works for the 1"-ish hole in my Fitness Gear power rack with my iPhone (Pro Max size). ...Should work for quite a few phone models.

... The rack mount bracket is for the 1U microphone reciever. This should be printed with extremely strong material. ... I used ColorFabb XT-CF20 Carbon Fiber Filament on an Ender 5 Pro with Micro-Swiss direct drive and hardened steel nozel.

This is a rack unit wall mount system. It empowers users to efficiently secure a standard rack unit (regardless of size - 10 inches, 19 inches or any other dimension) at the height of 1U directly onto the wall. ... Print Settings Printer: DAYCOM 3DP-100...

... 1.125", 38mm = 1.5"). Other diameters may follow. The hole distance on the base is 50mm. Required: 5 M3 nuts 5 M3x16mm screws self-adhesive rubber band, 2mm thick, 40mm wide 4 screws for mounting the equipment (I used 2.2x6.5 self-tapping screws)

EXTRA THICC Remix of 1U Rack Mount by colanabo. I recently acquired a large ~50lb 1U server that I needed to securely mount, so I imported the STL files into MeshMixer and reinforced the critical stress points. ... After printing in ESUN PETG, these...

You have two options for attaching this wall mount to your laundry rack frame: 1. Disassemble the laundry rack frame and then attach the wall mount. 2. Heat the wall mount with a lighter until it's soft. Then, open it up and slip it onto the laundry...

"Pretty close" to the original part, threads onto my G4 Bullet camera and holds it at the desired angle.

I made the arms a little longer on this to accommodate for the larger HD access point.

https://www.ebay.com.au/itm/3x-Rackmount-Cable-Management-19inch-Patch-Panel-1U-With-Brush-for-Data-Cabinet/184080087408?_trksid=p2485497.m4902.l9144 I used standard rack mount 1RU brushes from ebay. and made a slide to mount the Pis. ... this is...