undermount desk drawer 3d models

When I printed GodardScientific's Under desk drawer, the handle broke (beware when removing supports!).To avoid reprinting the whole thing, I made a simple handle to replace it.It's 2mm thick and should be sturdy enough for regular use.I use it just...

Desk drawer organizer trays based on 55x55 mm matrix. Also includes a compatible series of narrower trays for drill bits. The trays has a small handle in the top end which makes it easy to lift out single trays. ...It also has place for 9mm labels, such...

... Dimensions (approximate): L=200mm W=135mm H=37mm Cura estimates: Drawer is estimated at 8h19m requiring 121g of filament. Cabinet is estimated at 5h requiring 62g of filament. Instructions: 1.Glue rails to the corresponding letter; A:A, B;B.

then move the drawer and the clamps to your desk and take the clamps and press them against the pieces with little holes in them. This for the clamp contest. ...Look at picture if you are confused.1* body of drawer1* drawer of drawer4* clamp of drawer4*...

My little Under desk drawer! It has dimensions of 140x200x40 mm (W*L*D). It perfectly fits scissors, pencils, pens, etc. It is easy to print, and takes about 300 grams of plastic. no supports are needed when printing. I used a line thickness of...

I started with fixing one rails in place, then I slid in the drawer from the side while holding the second rails to it (of course with the double sided tape already attached to it such that you can stick it to your desk). I then fixed this rails and...

This is a simple drawer to stick on the underside of a desk. It is supported well enough with double sided foam tape, but the rail has holes so it can be screwed on if needed. ... It is sized to fit on a 200mm circular print bed, both parts print well...

simple under desk drawer, printed with .6mm nozzle, .6mm layer heights. Big enough tolerances to print with any settings. ... There are a few designs already on thingiverse, but i wanted one that would easily fit both parts on my print bed.

This is a simple drawer to stick on the underside of a desk. It is supported well enough with double sided foam tape, but the rail has holes so it can be screwed on if needed. ... It is sized to fit on a 200mm circular print bed, both parts print...

The printed version shown here needed the holes drilling out and countersinking to accept the four 100 x 6 woodscrews required for under desk mounting, but the STL file has now been modified, so hopefully the clearance for 6mm screws will be ok. The...

- The front face of the drawer is lowered which makes it possible to store items that are slightly too long and stick out (like calipers) - Finger indent underneath for better grip when pulling out drawer Installation Instructions: 1) Tape the...

# Mini Desk Drawer #### **__Creation Process__** --------------------- - If you're interested in seeing the creation process or some cool timelapses, check out our video: https://youtu.be/mE7KSwPcOpM - Programs Used: Blender, Illustrator. ####...

Once the pieces are printed, attach the mount to the desk, slide the drawer into position, and secure the faceplate to the drawer using super glue. Clamps or tape can be used to hold everything in place until the adhesive takes hold. The designed...

Under Desk Drawer5mm hole

Revamp your work desk without drawers by printing out brackets for either screw or tape installation, depending on your preference. Opt for a Sterilite 16-quart storage container due to its durable design and adequate size, available at Target,...

... bevel on the inner edge where the original ones are weak.Recommend printing standing up with 100% infill. Use painted on snug supports only on the pegs.Have posted STL and a fusion360 file incase you need to make slight edits for your own desk.

... more freely, however I have fixed the tolerances and these should slide nicely without any sanding needed. I used 6 x 3/4 wood screws to mount to my desk, they do have an angled countersink so keep that in mind when selecting the screws. ...

This here is a small desk drawer setup that I designed a while back. Its great for holding small  (think paperclips, thumb tacks, lapel pins) and slightly larger (pink eraser) items depending on your shelf configuration. I haven't updated the...

My printer, Prusa MK3s has a build volume of 250x200x200, this print maxes it out. The support gets loose and bends on the edges, but it worked out in my print. The drawer itself took around 16h to print, each rail 3h. </li> <li>The rails have to...

... and customize and improve on it. Perhaps there are other cheap desk organizers which can be made into drawers by changing a couple things, but this should work with any container with a lip as you'll set the spacing between the rails. ...Enjoy!</p>

Moreover, printing the top of the drawer standing up will help make it more solid because the weigh of the drawer won't pull the layers apart from each other, but will only pull the on material itself.If ever you use other materials, I'd be happy to...

Do you have a work desk without drawers and miss being able to store things out of the way? Then you're in luck, just print these out, pickup a cheap storage container and enjoy storage space for $3, without being in a cubicle. See the instructions...

Set of 2 drawers 193x185x170. ...2 versions of the drawers one set up to work with dividers one normal.

When browsing for drawers, it turned out they are around $100 so I made one myself. It is a sturdy drawer that organizes my glasses, Airpods, wallet and keys. About the printing process It is printed with 3mm wall thickness to make it very sturdy. ... ...

I managed to design this simple drawer in OpenSCAD, using a cylindrical shape that rotates around a single central peg. If it turns out useful, I'll post the instructions and any notes I take along the way. To attach it, I used a double-sided...

You must REALLY hate all that extra filament laying around to be looking at these..The chassis take about a kg to print, and the drawers, feet, and hats take another like 600g. On the bright side though it all fits in a 200x200 footprint so it should...

Originally I made the tolerances too tight so I had to do a lot of sanding to make it slide more freely, however I have fixed the tolerances and these should slide nicely without any sanding needed. I used 6 x 3/4 wood screws to mount to my desk,...

Cup holder designed to be placed over the drawer front of an Ikea bedside table.

The wide v1 drawer in half height to match the smaller half height one.

Cup holder designed to be placed over the drawer front of an Ikea bedside table.