under the desk shelf 3d models

i needed for my desk, in order to control thing that i dont move. ... i hope you can find some use

This ergonomic hook can be mounted underneath a desk with a couple wood screws to conveniently store one or two sets of headphones. Category: Office

A convenient headphone holder that attaches to your desk using strong double-sided tape, keeping your headphones organized and within reach.

I've got a wireless keyboard that's hogging valuable desk space, so I created this gizmo to stash it out of the way while keeping it within easy reach. It takes about 10 minutes per piece to print, and you'll get super simple, budget-friendly...

Under-floor storage units are designed to maximize space by utilizing double-sided adhesive tape to secure them in place.

*** what you need: *** - 8x M8 threaded rods (in my case 31 cm long) - 32x M8 Normal-Nuts - 2x M8 Hut-Nuts - 34 M8 washers - 4x M8x40 Screws with a flat hat (the hat is facing to the synth as you see on one of the pictures) - 12x Screws for mounting...

Küçük çekmece ölçüleri (içten içe): En:39 mm Boy:80 mm Derinlik:22 mm Büyük çekmece ölçüleri (içten içe): En:85.6 mm Boy:80 mm Derinlik:20 mm Kullanılacak Malzemeler - 3D baskı malzemeler - 3.5x15 Ağaç vidası (4 Adet) Under-Table Drawer Design...

Printed with supports beneath the screw tabs.

The wide v1 drawer in half height to match the smaller half height one.

The original file would not fit on my ender 3 so I chopped off the front angle and moved the foot back.

Remix to add a second hook dedicated to the cable. ... Changing the length for my Triton helmet v2: change the screw hole

... ... the flat part starts with 0.3mm ends with 0.7mm in order to make it easier to push it between to plates of the table (the horizontal and the vertical in my case). you may also use the flat plate to stick it to the plate (with 3M tape or other).

... 0.625" thick particle board. I also enlarged the diameter of the clearance holes to fit my Milwaukee Shockwave impact bit holder snugly. Since the holes expanded significantly, I widened the hook portion to ensure sufficient strength and stability.

Be sure to place the drawer inside the frame first before mounting, or it won't fit because of the stop that is on the bottom of the drawer!!!  The drawer has recesses on the bottom so that it can be mounted with double-sided tape instead of screws....

... noticed it could optimized to cut down on material and print time. ... Printed on ender 3 pro Print the Drawer flat and the mount standing upright on its end. ...I added brims to the drawer to stop it from warping and the mount to give it stability.

... assembly. To simplify printing, I separated the hook part from the top portion. The two parts are now securely attached using an M6-25mm screw. Furthermore, I incorporated an anti-rotate feature to prevent the parts from rotating after installation.

However, the source .f3d file is included so it should be rather straight forward to adjust the model to fit other remote sizes like those typically included with LED lights.The holder has slots cut out for IR passthrough for usage of the remote...

... PLA from eBay as it was the only white PLA I had laying around. ... I used 10% gyroid infill and it feels more than sturdy enough. I also put my logo on the front however the .STL file doesn't have that so you can put whatever you want on the front!

I was not able to find a mouse holder for the underside of my table so I designed one that fits the Logitech MX Master 2S. ... It does not require support material but it does require a bit of cleanup on the underside of the screw mounts.

I set my printer to standard mode and let the infill density dictate its strength.

... snuggly fit a Latitude 5430. ...The screw holes are recessed and sized for #6 wood screws, the hole in the bottom bracket was enlarged to allow for a ~7mm diameter screw driver to pass through. ...It allows for about 1mm clearance on the closed laptop.

I was not able to find a mouse holder for the underside of my table so I designed one that fits the Logitech MX Master 2S.It does not require support material but it does require a bit of cleanup on the underside of the screw mounts. 

You can use any screw you want or modify the FreeCAD file to fit your needs.

Simple but useful storage junk tray to help keep the clutter away.

Simple but useful storage junk tray to help keep the clutter away. 

Simple headphone hanger that can be attached to the bottom of a surface with wood screws, or an adhesive tape. ... I designed this because many of the other designs i found were overly large or complex

This project originated from a design created using Tinkercad. ...The user can easily edit and customize the model by accessing its webpage directly at https://www.tinkercad.com/things/dqU60DSX7o7.

Original idea was good stuff. I rounded off some corners because my printer likes to fail on corners. Removed parts that glued on, added hooks on the hook part. Separated the hook and top part for easy printing. Used an M6-25mm screw to attach the...

I left some tolerance just to slice the ps4 in place so it wont get stuck while placing

This is a small design for the Anker PowerExpand 13-in-1 USB-C Dock. ...It consists of a front and back to match the different clearances for the ports. Print “Instructions”no supports neededprinted at 0.25mmPLA worked for me