under the desk shelf 3d models

Desk_Shelf.stl - cleaned up version with 1/8" thick walls and a hole in the back for cables Desk_Shelf_Light.stl - same as desk shelf with some diamond shaped holes cut in the sides and some of the lip cut out to reduce filament usage. ... support...

those pesky temporarily used keyboards are always in the way. ... not any more. :-D the L-shaped thing is a drilling jig your drilled holes will be perpendicular to your shelf. The keyboard holder will be about 12mm behind the front of the shelf.

For assembly, use #8 fine screws and springs from Home Depot: a 9.5mm x 2.9mm x 1mm Compression Spring (685 436, Everbilt) for the clip spring, and a 6.35mm x 3.81mm x .89mm Extension Spring (685 383, Everbilt) for the other spring. ...Print parts...

I have allowed 40 MM height for the Band, this is designed to stick under your desk or a shelf to mount your headphones on for easy access, for gaming or video conferences i have tried to made it look unique and aesthetically pleasing.

I used a 600x200x16mm melamine shelf from bunnings to do this: https://www.bunnings.com.au/flexi-storage-home-solutions-600x16x200mm-white-shelf_p2710149 To attach the shelf, I used 4x M6 nuts and bolts, and 4x 2mm self tapping screws to attach the...

I used a 600x200x16mm melamine shelf from bunnings to do this: https://www.bunnings.com.au/flexi-storage-home-solutions-600x16x200mm-white-shelf_p2710149 To attach the shelf, I used 4x M6 nuts and bolts, and 4x 2mm self tapping screws to attach the...

An under-desk PC shelf intended for a raiseable desk. Upper bracket, Lower bracket , and cable management clip. ... Wood used is 2x2 Screws used are Flat Phillips Wood #10 x 1 in.

The person designed this straightforward riser for an under desk shelf with one primary goal in mind: keeping a laptop and dock out of the way. ... This task required finding a suitable base material, which turned out to be an Ikea chopping board...

Under desk shelf I made for my shiit audio stack. ...It is too big for my Prusa mini printer by default so I scaled it down to the below size and it does fit and work fine. X:58.9Y99.9(100 would just barely not fit)Z:100.

Under desk shelf I made for my shiit audio stack. I havent been able to test print it yet. It is sized to big for my printer by default so scaling wise I have it at. X:58.9 Y99.9(100 would just barely not fit) Z:100. This is scaling for the...

Desk Organizer for under my monitor shelf.Has 4 usb storage spots, 3 SD card slots, one 3x3 post it note storage.To cut down on printing time you can print at a higher layer height or a wider line width.

Desk Organizer for under my monitor shelf. Has 4 usb storage spots, 3 SD card slots, one 3x3 post it note storage. To cut down on printing time you can print at a higher layer height or a wider line width. ...

Under desk caliper storage, I got tired of moving my calipers every time I needed to do something, so I made this to get them out of the way.

Under desk caliper storage, I got tired of moving my calipers every time I needed to do something, so I made this to get them out of the way.

For 16 mm thick board The shelf holder can be mirrored in cura

shelf for laptop

I wanted to move my work laptop out of the way and off of my desk. I give you my own take on laptop shelf brackets! Instead of buying laptop hanging brackets for $10+ online I decided to design and print my own! It has two 4mm screw holes countersunk...

Went on sale for $20 and I jumped but upon getting it, discovered it was about an too deep thanks to a wing on the back to fit my desk so i decided to make my own which is an inch wider and half an inch deeper for storage than that was. It lacks...

This mount is a simple under the desk or shelf mount in a L shape for 2 14x19mm rocker toggle switches. ... Standard print quality .2 infill

... narrower. ... I only designed one side, you will need to mirror to make the other side. Both fit on my prusa MK2 at the same time. See more details about the build at my blog post: https://kiltedcraftworks.com/2019/12/08/under-desk-mess-wire-shelf/

... narrower. ... I only designed one side, you will need to mirror to make the other side. Both fit on my prusa MK2 at the same time. See more details about the build at my blog post: https://kiltedcraftworks.com/2019/12/08/under-desk-mess-wire-shelf/

LH and RH clips to put laptop under a UPDesk standing desk. The end of the clips have relief to place over a metal clip. Use 6 #6 3/4" or 5/8" fasteners to drill in. ...Part is designed to accept countersunk wood screws.

The holder for the Schiit Stack from Schiit Audio is a simple design to move the stack from above a desk to below a desk. Nothing special for layer height or material used. Command strips can be used to attach the stack to the bottom of the desk. ...The...

With this, I bought a small bucket from Bunnings and designed a basket to wash the resin prints with. Since desk space is always desired, I'd like to keep this bucket away but within reach. ... These rails will allow the bucket to slide in and out...

Hexagonal design with hexagonal cut outs, 30 mm wide with 30 mm opening, designed to fit Corsair Void Pro headset - headset_hook_01.stl - x5 cut-outs on the bottom and back of the hanger - headset_hook_02.stl - x4 cut-outs on the bottom and back of...

I attached this to the bottom of the my table with a couple of button head sheet metal screws and if the fit is too tight, you might need to use a washer or two to create some clearance between the calipers and the bottom of the table. There are...

lock designed to prevent patio umbrella from spinning around when tilted to block the sun. designed for a 37mm umbrella pole. May work for sizes ranging from 36-38, but not tested. If you found this useful, please donate what you think it is...

Specifically tailored for the powerful Dell m3800 system, this design showcases impressive craftsmanship. Made entirely with Tinkercad's intuitive software, enthusiasts can now effortlessly edit it online at...

Ikea Desk feetHolder for shelf under desk ikea foot diameter v. 70mm/ ikeafuss Durchmesser v. ...70mm / screw M6

I hold a hard drive and USB neatly under the desk, with an RGB remote nearby. I haven't printed the latest version, so the images are from the first one, but all I've done to v2 is add screw holes. I've added the Fusion 360 file with some user...