under desk mount for xbox one 3d models

Here is a basic platform that holds your Xbox One Kinect, without getting too fancy it simply gets the job done.

I needed a desk mount for my streamdeck V1. Designed it in Blender, fits perfectly, not sure about the V2. I recommend using some washers for mounting it. ... It's ready to be printed, you don't have to do anything but slice and print.

Check out my V2 version, which boasts a bigger air gap for improved cooling.\r\n -I just got a PS4 Pro and needed an under desk mount because space is limited on my table. ... After browsing through various mounts online, I decided to create my own...

... save space and remove the cluttered appearance of the cables. These and the Caldigit TS3+ version have been very popular in the office.The mount is design so that you can remove the docking station for any reason by disconnecting all of the cables.

I created this because I couldn't find any suitable wall mounts for the XBOX One Kinect that were strong and had enough clearance for the cord coming out of the back. The design is inspired by <a...

I have a 17'' Laptop that is so old that I need a laptop cooler pad when gaming due to overheating.To store both stacked underneath my desk a very large dektop holder had to be modelled.This creation needs no supports.The size is 9,3cm (inner height)...

You can use this thing to mount one unit rack devices underneath your work surface. You might have to reverse the direction of the rack ears on the mounted device. I utilized these to install two one unit power distribution units beneath my desk. ...I...

It mounts the dock upside down underneath the desk. It is in two pieces in order to print in full on smaller printers. I created this in Blender 2.79. ... STL files from blender, in my experience, tend to come out much smaller than the original...

In an effort to clear some room on my desk, I relocated my charging hub from its previous location at the top of the desk. I was in the middle of making a new mount when it dawned on me that the desktop stand I had already made might be tweaked to...

In an effort to clear some room on my desk, I relocated my charging hub from its previous location at the top of the desk. I was in the middle of making a new mount when it dawned on me that the desktop stand I had already made might be tweaked to...

It works perfectly for my Panasonic headset and is secured under the desk with just two screws. This design features a rounded edge in front, making it easier to load or unload the headset. For optimal results when printing: Start by printing support...

... no where else to cable manage it! You may need to change the measurements for the part that connects to the desk because that will vary; or you may need to make the spool smaller in order to print on smaller printers like my Ender 3. ... Enjoy!

After trying out lots of under desk cable management options, I always ended up with issues with tangled cables and the need to re-arrange them when adding or removing stuff under my desk. So, I decided to design my own and think it fixes the issues...

This is a remix of https://www.thingiverse.com/thing:2191646 which is a remix of https://www.thingiverse.com/thing:716092 designed to mount to a wall instead of lay on a desk. For best strength, print sideways. ...Leave a comment below telling me what...

Double USB Holder attaches securely under any standard office desk, providing a convenient place to organize and manage USB cords. ... USB cables utilized with this holder typically feature a width of approximately 18 millimeters, while the height...

I engineered a solution to relocate the docking station underneath the desk, thereby freeing up valuable space and eliminating the cluttered appearance caused by cables. Our office has seen significant interest in these and the Caldigit TS3+ version....

I wanted the Xbox controller stand to have some colour, so I added black in the logo to represent the Xbox One S logo. This was remixed and designed to fit with the https://www.thingiverse.com/thing:1978236 Xbox controller holder. ... It fits...

Any docks/hubs with the same dimensions should fit this holder.I wanted a clean solution to mount this below my desk. This is secure and easily removed from the hub for any reason.I initially printed on it's side(no supports) however with no brim it...

I wanted to keep my controller off of my desk when not in use. ...This will allow your controller to be plugged in while on the mount, and catch your cable when you unplug it. ...It also accommodates most dongle holder mods.

... a pistol from under the table while trying to get Bruce Banner (Hulk) to help S.H.I.E.L.D. ...find the Tesseract after Loki stole it. My dad asked me to 3D print him one for Christmas...Hope you enjoy it, let me know how it works and stay Awesome!!

This is a revised take on the Xbox Controller Hanger (360 and One) by SmithRC. I've modified it to fit snugly onto a 0.625" (5/8") diameter shaft, which I've secured to a floor lamp purchased at Walmart. To fasten the two parts together, I'm using...

I was really impressed with the 1U Rack Mount Brackets from colanabo, but they only suited my needs for a single unit at my feet. ...I took matters into my own hands and adapted the brackets to accommodate two 1U devices in place of one.

This is a remix with added tapered holes for mounting with screws.

Same as v2, but taller to clear my desk hardware and thick laptop

Thanks to delsmith40 for the design. ... Added a front sight grove, thickened the mount plate, tapered the mounting screw holes and tapered the guide to ad in insertion of the launcher.

Staying productive at home just got a whole lot easier thanks to this clever desk accessory, which keeps your workspace tidy by attaching the headset's controller in a secure spot underneath the desk.

Backpack Hook in order to hand underneath a desk. ...Holds mine with stuff in it (estimated 10lbs/ 5 kg).

A sleek desktop accessory designed to securely fasten headphones beneath any workspace. ...The mounting holes are precisely crafted for easy installation using standard #7 machine screws.

... a 20% infill that's more than enough, and maybe even less is sufficient. ... One of the images shows the screws in plain sight. That's due to an outdated version of this mount; the current iteration will recess the screws so they're not visible at all.

I didn't come across a mount that caught my eye, so I created one myself, drawing inspiration from the designs I've spotted here. It's specifically designed for use with double-sided tape. While there are sleeker options available, I wanted to share...