ultra view archery 3d models

I printed with TPU "flexible" filament at 205c, setting the build plate to 95 degrees. To achieve vertical printing, I dramatically reduced the print speed. The slot partially fused together during the process, so I carefully cut it open with a sharp...

COMPETITON BOW SIGHT

Just flat figure with separated stand

The 3D model was created from actual base. It’s created accurately, in real units of measurement, qualitatively and maximally close to the original. Model formats: - *.max (3ds Max 2008 scanline) - *.max (3ds Max 2008 vray) - *.fbx (Multi Format)...

Simple stick-on arrow rest for recurve or low power bows. Tested and works well on a kids LIL'Banshee compound bow. If you want to see more and how I create prints and 3D designs like this check out my YouTube channel.

Tool for adjusting the alignment of the arc. Just buy a small Parkside vice at Lidl, tap in M3 and M8 5/16 the base 3 and you're done. ... Material: Threaded rod M6 Nut M6 Screw M8 5/16 HC screw M3 Good setup!!!

This model was created using Tinkercad. ...You can modify it directly at https://www.tinkercad.com/things/dHaNLqZoTGS.

Based on models I'd seen online, This tab sandwiches leather between two printed plates. A ring screws in through the whole assembly and acts as a finger spacer. Used 3 pieces of leather (about 1mm thick each) PDF of leather pattern included in...

I HAVENT HAD A CHANCE TO MAKE THIS AND TRY IT YET BUT I DREW UP A WALL MOUNTABLE ARROW HOLDER.

Hi Everyone! I designed a clicker that fits the trapezoidal mounting arm, commonly found on high-end sights. Print Options: The images I uploaded show the body printed on an SLA AnyCubic Photon and the arm printed on my RepRap Guru Prusa FDM...

Very simple and cheap pouch to throw in release tool while pulling-out arrows from a target. Use old shirt sleeve for pocket and two sided tape. Works. ... Attaches to belt.

TPU is the only material suited to this print. The stringer has a unique clamping action that requires a flexible strong material which is why TPU is the best filament to use. Bowline knots are required to tie on the TPU prints to either end. The...

Foot pegs for archers. There're two versions, normal (53mm) and longer (63mm) version. The .stl file doesn't have name on it. I also uploaded the .f3d file, if you want to make any change or add your name. ...

Simple 2-piece jig spool design allows for easy winding and snapping together. Wind the serving onto one half, then fit it into the other half. This symmetrical design eliminates the need for supports. Print two pieces and snap them together firmly.

In our indoor-Hall we somehow didnt have any nails to put up the target faces on the buttes. A quick design-job and print-alongside-homeoffice yielded us a case full (around 1.5kg) of nails even with the logo of our club. ... I included a blanc here...

### Info First time I printed it with small lateral tips, but this damaged the main tip (probably bad slicer settings) - pic. 3, so I removed it, because lateral tips are not necessary. **no support needed** (except "*target_pin_v2_type_C*" and...

平台为Hyper Hyte，64磅，拉距28英寸，内径4.2纯碳箭杆。 普通的4.2纯碳，外径一般在6.1-6.3之间。但传统的FOB箭羽，内圆直径固定，无法弹性扩展，如果入手的箭杆口径有差异，很难做到无缝适配，我打算改进它。 FOB-1：将内圆开槽，试图增加对口径的弹性适配，试射发现，入靶后惯性力道太大，FOB与箭杆打滑。 ...

Armguard. Protects your arm from being hit by the bow string. Can also be used to contain loose sleeves when shooting, and thereby reducing the chance that your clothing interferes with your shot. ...

### Info Both designed for 8mm arrows. I print arrowhead with 100% infill PLA and it works fine. For more durability, you can use etc. PETG, ABS. ### Recommended usage: + Use the extender as close to the tip as possible for maximum...

Set the slicer wall thickness or number of perimeters so that the arms and teeth of the wrench head are solidly constructed. No infill or supports are required as PLA is remarkably strong enough and the print is not sensitive to layer height. The...

Clou blason, cible, tir à l'arc Utilisé un clou de diamètre 3mm avec une tète maxi 5.30mm

Customized Version of Thingiverse: https://www.thingiverse.com/thing/58001 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=58001 Instructions Using the following Options: pattern_overlap = 18 ...

This simple arm guard is perfect for archers in the Makerbot community who are on a budget. The creator decided to make their own because their school's class didn't have enough and needed to save money. To print, ensure it's upright with the widest...

I needed to serve (wrap with thread) my new bowstring. This can be done with a loose roll of thread, but it's much easier with a jig to hold the thread in tension. You can buy these jigs online for $10-20, but I'm impatient. Instead I designed and...

I crafted this tool to balance my arrow on a tiny, high-precision scale.

Tried most rings available for download and found that none is perfect, is allot about customization (individual physiology) and also personal preferences so i decided to design myself one based on turkish/ottoman design... at the end resulted in 2...

Thank you for supporting me!This is another free 3D model made available for you. I love sharing my models, but designing, testing, polishing, uploading and maintaining them is a lot of work. In case you enjoy this model, please leave a small...

These arrow shafts are specifically designed for Beman Easton Carbon Composite Arrow Shafts, featuring slim Procomp 1416 (7/32") x 32.5" in length. The outer diameter measures 0.21" (7/32", 5.5mm) while the inner diameter is 0.15" (5/32", 3.85mm). ...

Tools for Fletching with spin vanes, marking jigs & vane holder. Jigs in 1mm stages from 5mm upwards, designed for use with shafts having pin nock attachments but will also work with no pin or nock fitted. ... Vane holder works with most vanes and 3mm...