ultimaker vs raise3d

Raise3D Pro2 spool holder that supports 4 bearings for different sized spools

Filament Funnel Guide for Raise3D N2 and N2 Plus Use Super Glue After Assembly Print Settings: Printer: Raise3D N2 and N2 Plus Resolution: 0.15mm Infill: 15 Percent Notes: Funnel facing up on bed, including hole in retainer box

Received a printer with two missing plugs for filament holders, so had to print this... ...Printed with Raise3D E2.

R3D ABS Filament - [www.raise3d.com](http://www.raise3d.com/collections/all/products/r3d-premium-abs-filaments?variant=18559398721) Oct. 9, 2018: Created a brand-new clip that seamlessly integrates with Hatchbox filament, offering an incredibly...

Drucker: Raise3D Pro3 This is a component cooler for the Raise3D Pro3. Since the part is a bit more complicated, a few support structures have to be set. The front part is attached so that it can be unplugged when changing the Nozzle. 2 M3...

This project includes a runout sensor for RAISE3D printers. ... Warning: This project remains in the development stage, with ongoing improvements and updates.

Spool holder for Raise3D Pro 2. Use two 608 bearings (Outside diameter: 22 mm, Inside diameter: 8 mm, Width: 7 mm) ABEC 11 would be perfect! ... - Easy to fit - Can hold any spool - Door can be closed completely - Smooth rotation

An extended spool holder for the Raise3d Pro3. ...Printed with PETG.Mounted with 3 DIN912 M4 x 30mm screws on the printer.The door still closes, it is only bent a little bit at my printer.

An extended spool holder for the Raise3d Pro3. ...Printed with PETG.Mounted with 3 DIN912 M4 x 30mm screws on the printer.The door still closes, it is only bent a little bit at my printer.

I opted to acquire additional high-temperature ends for my Raise3D N2 printer to accommodate various nozzle sizes, finding it more convenient than frequently switching out the nozzles. ...Consequently, I required a means to store the unused nozzles...

Testing the capabilities of this platform requires evaluating its levelness and height, especially when printing with a Raise3D N2 (Plus) 3D printer. ... Check out www.3dwp.nl for more information.

Designed for mounting a pair of 5015 12v radial fans in a Raise3d Pro2 series reaching the maximum layer airflow. Improving surface quality, bridges, and also allows increasing printing speed. ... Note: you will need to recalibrate PID settings.

This is a snap-on fan grille designed specifically for Raise3D N2 and N2+ 3D printers, featuring 35mm fans that attach securely to the fan housing without any hassle.

... cables from disk drives, so I made this as a precaution to prevent it from happening again. Print Settings Printer: RAISE3D N2+ Rafts: Yes Supports: Yes Resolution: .15 Infill: 25% Notes: I used RAISE3D PLA at 205 degrees. ... Custom Section

Upgrade your Raise3D N-series printers with our premium fan ducts, designed specifically for the E3D v6 adapter. We've got you covered with two fantastic options: * 35mm Fan Duct: This compact design is perfect for cold end only applications,...

Print settings for the Raise3D N2 Plus printer are optimized to ensure high-quality prints. To begin printing in ABS, navigate to the Print Settings menu and select the Raise3D N2 Plus as your printer of choice. Under Rafts, choose Yes to enable...

Simple Spool Holder Upgrade for Raise3D Printers: A DIY Solution. My custom carbon-fiber PETG arrived on an oversized 78mm wide spool, necessitating a creative solution. ...This innovative holder is designed specifically for use with large diameter...

Customization of the existing N2 spool holder by Ponzerelli to fit the Raise3D Pro2 Plus. ... - revised overall length to fit within Pro2 Plus case - revised width to 70.5mm to fit standard 68mm spool width - revised attachment to fit slot -...

The Raise3D printers come equipped with noisy 35 mm fans, so I swapped them out for quieter 40 mm fans and was able to bring down the noise level to a more acceptable range. ... These fan ducts take the place of the stock ones and are installed in...

Here is the rewritten text: The fan shroud for the R3D stock 35mm fan with an independent 30mm layer fan is available, but it's only compatible with the Raise3D E3D v6 Hotend Adapter - using it on the R3D stock hotend won't work. ...You'll need to...

Focused heat sink cooling for stock hotend of the raise3d n2 series. Designed for a noctua 40x10mm 12v fan. ... ...

This is an improved airflow system specifically designed for the Raise3D N2 / N2 Plus to enhance cooling efficiency on the motion board. Printed inside with ABS material Exterior printed with Polyflex material Additionally, a piece of activated...

... Head as well. ... Print Settings Printer: Raise3D N2 Plus Dual Rafts: Doesn't MatterSupports: Doesn't Matter Resolution: .2mmInfill: 10% Notes: for best results and durability print with temperature resistant material! ... Category: 3D Printer Parts

Introducing a new fan holder designed for Raise3D N2 Dual, compatible with Bond Tech Extruder. It functions seamlessly with PETG and PETG Carbon materials. ...The product includes a SolidWorks model: access "Luefterhalterung_Rahmen.SLDPRT" by keeping...

The official fan mount that comes with the N2 & N2 Plus Printer is designed to work seamlessly with Dual Head functionality.\nPrint Settings\nPrinter: Raise3D N2 Plus Dual\nRafts: Not Applicable\nSupports: Not Required\nResolution: 0.2mm\nInfill:...

The Raise3D extruder board has a protective cover, I edited it for dual color 3D printing and made this black and red ABS print on my N2 Plus Dual.I used a wipe wall and printed this with 0.15 mm layers, I also added the Ideamaker...

... the mounts and attach them to Greenlee's front fan mount found at https://www.thingiverse.com/thing:2745671. ... The pump mount leverages the existing hole on N2+ and should be compatible with other Raise3D printers that have a similar hole in place.

Print Settings: Printer: Raise3d N2+ Rafts: No Supports: No Resolution: 200 micrometers Infill: 100% Notes: Bed offset is set to (2,-10) despite the origin point being precisely at the left front corner. This adjustment must be made in Advanced...

The sides of my design rely heavily on the critical Raise3d design, which was released for reprinting and incorporated into my design to hold the back part in place. The first version didn't allow the back part to slide down, so this second version...

This is a replacement for the left-handed fan mount on a Raise3D single nozzle printer. My printer is the E2 Single v1 extruder. It was designed to be used with this dial indicator for bed leveling:...