ultimaker s5 calibration 3d models

I liked the idea behind dial gauge holders that I'd seen for Ultimaker, but had a few additional requirements: - No chance of accidentally ramming the gauge into some other part of the printer. - Quick, tool-free attachment and removal of the gauge....

The original Ultimaker radial fan is known for its poor quality. A replacement that replaces the entire cooling assembly is now available, inspired by designs from http://www.thingiverse.com/Sonarok. This improved version works with a 40mm fan and...

This replacement annular cooling is for the Ultimaker nozzle, as the original cooling shroud can sometimes be counterproductive due to its unidirectional nature that may lift the first layer during printing on a raft. The new design aims at the...

This replacement is designed to eliminate the noisy, low-quality electronics fan that comes standard with the Ultimaker Original. The supplied fan has well-documented issues with its bearings - they become noisy and require regular regreasing. Mine...

... and compatibility for PLA or ABS filaments. Printing at 120mm/s speed and 0.2mm layer thickness, infill 20%, wall 1.5mm takes approximately 2 hours and 30 minutes on an Ultimaker. ...Refer to a screenshot for proper bed placement of parts.

My latest creation is inspired by the Ultimaker, which uses linear shafts as rotary transmissions. Despite not updating it for nearly a year, I've decided to release the design as it stands. Key features include an 8.5x8.5x8.5 build area, compact...

I didn't care for the Ultimaker's essential components being positioned at the rear of the device, making them hard to access. Additionally, I'm constrained by a cabinet with limited depth, necessitating minor modifications to secure a snug fit. To...

After searching for one compatible with my Ultimaker, I designed a simple version using OpenSCAD. The sponge causes minimal friction, so there shouldn't be any issues with printing or retraction. I'll monitor the results and possibly modify the...

Firstly, print the Ultimaker Z-axis end-switch fine-adjuster (available at http://www.thingiverse.com/thing:11033). Then, insert two nuts into the designated notches. Proceed to attach a forked light barrier from an old desk scanner. Next, integrate...

Les lignes à gravier sont celles en noir et en gris, tandis que celles à couper jusqu'à la totalité de leur épaisseur présentent un trait rouge de 0,01 mm (0,028 po) et sont destinées au porte-outils 3D Ultimaker. Le dessin comprend également des...

... minimize shaking. You can even screw through the wall (check out the picture). The screw used was 29mm long and self-tapping. Printer Settings Printer Brand: Ultimaker Printer Model: Rafts: Not necessary Supports: Not required Infill: At least 60%

I've secured my printers on a sturdy metal shelf, which is indeed convenient, but I've encountered an issue with the wooden feet of my Ultimaker Original - they're somewhat slippery (I've narrowly avoided a few close calls). To address this problem,...

Two EasyClips for Ultimaker machines are now available - just what I needed! This TWO-part set is an optional component from CP-v7 (Co.Me.Do. - Part No: 7). You won't need any extra components to use these printable objects. For updates on...

A cable management solution for the Ultimaker 2 system is required to prevent Bowden tube movement. UPDATE: Version 3 offers an adjustable hook position, allowing for increased flexibility in managing cable tension. Additionally, this version...

To enhance the performance of an Ultimaker 3D printer, replace its power supply with a 400W 24-volt PSU and install a new PCB with pre-soldered LEDs and resistors. Order components from Ultamachine for $2.98 and a PSU for $49. Purchase a mill...

To print the file in nice colors, follow these steps: screw it onto the Ultimaker extruder head using the existing plunge or printing a new one with just rubber. The trick is to use the filament to push the plunge. For better retraction, light up the...

This bracket enables attachment of a standard 24-volt power supply to your Ultimaker using three existing frame holes, ideal for those adding a heated bed. The upgrade ensures sufficient power for the heater load. To install, first attach the adapter...

I used flexible PLA from Ultimaker for the flaps on the back, allowing the bowden to move freely without much restriction. Without these flaps, heat escapes easily. After installing this modification, a 120W powersupply can heat up to 70'C in about...

I design and manufacture my own custom wrenches for working with M3 nuts that have a 5.5mm hex head on my Ultimaker Original Plus printer. Unfortunately, most socket or wrench sets available in the US do not include a 5.5mm size, making it difficult...

I was determined to create a simple top and front cover to enclose my Ultimaker 2 Extended in order to maintain a higher ambient temperature inside the printer for ABS prints. For the top cover, I decided to purchase a Sterilite 16 Qt storage tote...

Several months ago I crafted and assembled an enclosure for my Ultimaker 2 to print materials like ABS and polycarbonate with improved layer adhesion. The enclosure is constructed from 6mm laser-cut MDF and secured together with M3 screws and nuts.

This is the full set of files for an Ultimaker 2 or 2+ enclosure, featuring a top box and a removable door. Several variations exist across some parts: Window Fixture: Two versions are available - one with countersunk holes for screws and another...

Leveling the Ultimaker 2 is a straightforward process that requires no special tools beyond a feeler gauge and a screwdriver. Begin by removing the build platform from its cradle, then locate the eight leveling screws located along the edges of the...

The part was printed in PLA using my Ultimaker, with Cura 14.03 handling the slicing duties. Design work was conducted using ViaCAD v9.1. Print settings included a layer height of 0.2mm and fill levels ranging from 80% to 100%, with no support...

Fix a popped-out bowden cable on your Ultimaker with this clamp solution. Drill two holes to secure it in place, preventing future damage to wood teeth. This clamp is printable in a reasonable time, featuring round edges for safety and internal...

We recommend purchasing some additional feet specifically designed for the Ultimaker original printer. These stabilizers greatly reduce noise pollution and significantly minimize mechanical vibrations while the machine is operational. To install...

The connection system mimics that of the Ultimaker, utilizing tabs and screws for added stability. By adopting this method, I was able to create a very stable casing that fits perfectly on my UM2. In the photos, you may notice that the...

An attachment for the Ultimaker, this tape holder snaps onto its sides to keep your tape rolls neat and tidy in the lab. Version 2.0 was released on August 10th, featuring three different sizes with an extra 1mm width to accommodate tape rolls and...

It firmly attaches to the Ultimaker, particularly ideal for lightweight webcams (like Logitech 920C). Mounting options include securing it at three center frame bolt locations or positioning it on frame posts for varied angles, totaling nine possible...

The Z-axis on an Ultimaker printer relies solely on the bottom coupler, which may exhibit minor lateral movement compensated by XY plane's Z brass nut movement. To ensure stability, an additional object can be used to secure the upper end of the Z...