ultimaker s5 bowden tube 3d models

I converted my Ender 3 v2 Neo to direct drive and needed some reverse bowden tube holders.This one goes where the old extruder was. ...Unfortunately one of the holes doesn't line up quite right, so it is only fixed with a single m3 bolt and nut

Simple cutter for Bowden or Capricorn tubing for 1.75mm filament. Uses standard single edge razor blade. ...Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: 0.2 Infill: 20% Filament: Hatchbox PLA Any Color ...

Elongated the tab slightly and added a 3mm hole. ...As illustrated in photo, use a paper clip to remove and reinstall clips. No more clips flying out of your fingers and vanishing! The paper clip can also be used to store your extra bowden tubing clips.

The Alfawise U30 requires you to align the bowden tube directly with the extruder to minimize friction during operation. This component also serves as a holder for cables connected to the extruder, keeping them organized and secure. ... You can print...

Human: I created a bowden tube cutter using a 10mm utility knife and an M3 x 10 bolt. It's surprisingly simple yet highly effective. I don't use it frequently, but when I do, it's incredibly satisfying to work with. ...The design is perfect for a...

Secure the Bowden Tube Clip firmly in place to prevent it from shifting. You might need to adjust its height based on your specific printer configuration. ... **Printer Information** Contributed by: Eustathios **Filaments Used** Colorfabb Red filament...

K1 cable chain clip to allow placement of the bowden tube on top of the cable chain. ...If your have extrusion issues this may help with the addition of a lid riser.Updated: As requested I have created a side mounted clip.

... **Required Materials:** - Three M3 x 5mm Screws - A 9mm Stanley Knife Blade - Bowden tube for cutting Assembly should be straightforward, if not please refer to the provided images! ... **Enjoy printing and cutting!** (Remember, don't cut yourself!)

I have had to remove the bowden tube on the Creality K1 more than I have had to do on any other printer I've owned. ...I've redesigned the clip slightly so I can actually grip it and retain my hold as I remove it.

Cordless cutter designed specifically for cutting Bowden tubes with precision accuracy. Includes a built-in squaring mechanism for perfect cuts every time. ...A 3D sketch of the design is available in Sketchup format, allowing users to customize and...

... as opposed to the "Full top case," which is designed to replace the original wooden components entirely. Note: The images provided were captured using a beta iteration of this Bowden clamp (the holes for the Bowden tubes were inaccurately sized).

Here are two useful tools for people who need to remove and/or insert their Bowden tubes into or out of fittings.\r\n\r\nDon't wait until you need these; print them in advance so they'll be ready when you do.\r\n\r\nFirst, there's the pair of slip-on...

This is a custom "Bone" shaped part that secures bowden tubes in place, specifically designed for use with my Dual Extruder mount found at https://www.thingiverse.com/thing:2734717. The center to center distance between the mounting points is 20mm,...

This is a 65mm extension for PTFE tubes in your bowden extruder, perfect when you're short on time and can't get one quickly - I'm speaking from personal experience here, as I was stuck with no shops open and a burnt-out tube end. To install this...

If your Bowden acts like mine, the Teflon tube rarely stays tight in the small push lock brass fitting. Even with the little printable clip that forces the plastic ring to stay up...over several prints it would eventually wear a groove in the Teflon...

The original cut Bowden tube that come with the Microswiss setup is too short, and if you print TPU, it will tend to pop out of the side of the gears where the lower tube meets. This jig cuts it a bit longer so it almost touches the bottom of the...

A simple cap designed to fit snugly over the end of a Bowden tube with the intent of sealing them closed. The hope is to keep air and dust from getting in to an otherwise sealed filament dry box. Specifically sized to fit over Capricorn tubes but...

I was tired of zip-tying my bowden tube to the hotend cable wrap and cutting them off every time I needed to change something, so I chopped these clips off of ZoltanKi's clip/mount. I printed it light with 2 wall lines and 10% infill, and they barely...

I remixed Pomi's desing so it can fit bowden tubes and so it cuts straight. I also provided the STEP files for both the remix and the original. ...For instructions go to the <a...

This is a simple bracket for protecting and supporting your Bowden tube and electrical wiring on the hot-end. It is designed for the Ender 5 Pro, but it simply clips over the back plate (2,5mm) and has a slot for the shaft of the roller. Sure it will...

I'm glad to share another small thing - bowden tube clip. All content on my page, including models and everything I've created, is covered under the WTFPL license (Do What the Fuck You Want). If you're pleased with my work and I've helped you out, a...

These cable clips allow you to attach cables to a 4 mm PTFE Bowden tube, like for example the hotend supply cables on an Ender 3. Never waste zip ties again! Choose a cool color and print four or five of them, then simply clip on your cables. This...

I Designed a Solution to Prevent Bowden Tube Movement During Printing, and It's Working Great. I Initially Tried Clips, but They Didn't Quite Do the Job, So I Came Up with Something New. Hopefully, This Will Help You Out If You've Been Having the...

Upon testing my Z-Height upgrade, I found that my Bowden tube was rubbing against the M8 bar at the top of the machine frame during upper layer printing. To solve this issue quickly, I created a simple cover in Autocad which securely attaches to the...

I wanted to build my own little Bowden tube cutter, this is the result. The hole is very narrow to keep the tube as straight as possible. The slot for a cutter knife (for a 0.4mm thick blade) is also narrow and high, so that the blade is as straight...

I had a few problems with filament that got stuck in the Bowden Tube, so I tried to remove the connector from the filament feed drive. I end up breaking the connector. This was an Amazon purchase Creality upgrade kit, but it did not have the screw...

Bowden tube coupler clips are designed to eliminate any slack in the coupler's retaining piece. They can significantly minimize the amount of retraction needed if the retainer insert is shifting during retraction, and they can also reduce wear on the...

This is version two of a Bowden tube clamp using a nut to compress the fittings instead of a zip tie. I used part of a design by krtektm, who also created a compression type fitting that inspired my idea. It should fit standard 4mm PTFE tubes and...

Bowden PTFE tube cutter for cutting both PTFE and capricorn tubing. The remixed design includes a locking spring pin and bushing. The redesigned pin locks into the bushing and prevents the pin from sliding out. As the pin must flex a little, I...

I needed a reliable bowden tube cutter - I'd used the one I linked as a remix before, but it had unnecessary extra slots.\r\nAlso, it lacked the angled "roof" required to prevent the sagging filament from reducing the diameter - which prevented the...