ultimaker feeder extruder filament upgrade 3d models

I designed it specifically for the new feeder upgrade from Ultimaker, replacing the delrin ring entirely. Use at your own risk, though - test it out first to ensure compatibility with your printer. To install, make sure the infill is 100%. The fit...

Upgrade from Ultimaker's standard delrin ring. Proceed with caution, as it may affect your printer's performance. Assemble with a tight fit; adjustments might be necessary based on your printer's specifications. ...Consider increasing the outer diameter...

This feeder plate boasts a significantly higher number of tightly spaced gear holes compared to its standard counterpart, ensuring that filament jamming is effectively prevented.

Upgrade your Ultimaker's feeder with this 3D printable part, which significantly reduces friction caused by stock components. Easy to assemble and install; simply replace the original part with the provided roller (10x6x3) for enhanced filament feed....

The upgrade includes printable modifications to all three components while maintaining fidelity to the original Ultimaker design. To implement this, you'll need a 6mm ID, 10mm OD, 3mm wide bearing, available for £1.99 on eBay. This modification...

Instructions: Once printed, take apart your old feeder and use a standard nut - not one with a lock thread - and plop the bearing on. Away you should go. It's a little tight getting it in there, but it works nicely. Make sure to print it with 100%...

Follow the instructions carefully: disassemble your old feeder, use a standard nut, place the bearing, and ensure proper tightening. Print the modified model with 100% fill for optimal strength. ...To check movement during printing, add black dots on...

Grow weary of the feeder constantly detaching from the Ultimaker frame when pushing filament manually? Worried it will fall off during movement of your box? Simply attach this accessory in the available space above the extruder arms to secure it. ...The...

... is not critical, with a vast adjustment range. Additionally, measurements on extruder drive force can be found at http://www.vinland.com/Extruder_Drive_Force.html. ...The long screw is 50mm, while the shaft screw should be 20mm to fit the 18mm yoke.

Introducing a replacement for the original wooden extruder gear, compatible with both Ultimaker Original and Ultimaker Original+ printers. Previous designs were unsatisfactory due to tooth profile inconsistencies or difficulty in fastening stepper...

This upgrade enables stock Tevo Tarantula filament feeders to print flexible filaments with precision. When printing flexible filaments, they tend to bend and get squeezed out of their path due to the stock feeder's lack of a filament guide and its...

Human: Filament Feeder Tool assists in maintenance of Ultimaker2 filament feeder by providing a wedge type tool. The problem arises when you remove the filament feeder, causing the filament drive motor to shift into the case and rest on the motor...

Inspired with adaptations from IRobertI "Alternative UM2 Feeder - version two" https://community.ultimaker.com/topic/11495-alternative-um2-feeder-version-two-about-robert/ It prints very accurately and no problem from vibrations. Can print TPU as...

This upgrade builds on the Filament Feeder found in edwardchew's CR-10 Spool Holder Top Mount & Upright Filament Guide. Every aspect of the original design is exceptional, except for one thing; the filament feeder itself. Due to excessive friction...

... Deforms Filament and Tears It During Retractions). To Accommodate the New Bearing, I Must Enlarge the Aluminum Attachment by Grinding. For More Information, Search Instructables.com for: MK8 Metal Bowden Extruder Wire Feeder Ultimate Upgrade.

... printing. Following the print job, I drilled out the filament path using a 2 mm drill bit. This action created a smooth and seamless path for the filament, allowing me to insert the coupling thread without any additional post-processing steps.

Ultimaker Extruder Filament Holder Replacement Directions My Ultimaker extruder's filament holder had a bad attitude - it loosened during long printing sessions. So, I replaced it with a new one featuring a lock nut. After testing it with 2-4 hour...

The Bertho extruder upgrade for Ultimaker includes modified blocks with spaces to insert metal plates, ensuring that the T-bolt adjustment screw head is secure. ...These aluminum plates, measuring 9.6 x 9.6 x 2.0 mm, strengthen the area to prevent...

This feeder and filament guide suit the Ultimaker 2.The pinching pressure of the filament can be adjusted thanks to a clamping screw. A latch and a hook allow to quickly remove the filament. Two aluminium tubes guide the filament in the feeder for...

This feeder and filament guide suit the Ultimaker 2.The pinching pressure of the filament can be adjusted thanks to a clamping screw. A latch and a hook allow to quickly remove the filament. Two aluminium tubes guide the filament in the feeder for...

However, when I purchased conductive filament, I encountered a major obstacle: the feeder system of the Ultimaker series cannot accommodate 1.75 mm filaments. Buying new kits was prohibitively expensive, so I took matters into my own hands and came...

When I buy conductive filament, I faced with a situation that feeder system of the Ultimaker series are not supporting 1.75 mm filaments. Buying new kits was expensive. So I decided to solve this problem for my big goal and come up with this...

Locking them is important to prevent the smaller tube from being pushed up from the force of the filament feeder.\nThe hot end components (Olson Block, Peak, and Tips) have been replaced by ones designed for 1.75 mm filament.\nPrint Settings\nPrinter...

Download the Ultimaker 1.75mm Filament Conversion from http://scottmayson.com/portfolio/ultimaker-1-75mm-filament-conversion/. Drill out one Push fitting to Dia 4mm, so PTFE fits flush with heater barrel. ...Upgrade your UM to 1.75mm filament and enjoy...

This is a little upgrade for your stock extruder ( feeder) of the Anycubic I3 Mega M to make the filament insert a little bit easier. It's really hard to change or insert the filament with the stock feeder, and if you dont want to replace the whoie...

After crafting the overhead filament spool holder, I designed a feeder system to assist with threading the filament directly into the FlashForge Finder's extruder. ...The new setup allows for seamless integration of 1kg spools into my small but mighty...

Repair of extruder feeder. It fixes pressing lever damage problem. Using original thrust lever as a template, I cut it from 3mm steel sheet and ground lever base to precision fit. Tapping M3 thread and using roller tap M4 are required for secure...

This filament driver, paired with a hobbed bolt, has successfully operated on my Ultimaker for ten months, even with PLA material. Originally designed for 3mm filament, it can also work with 1.75mm due to the hobbed bolt's functionality. The current...

The MK9 is a driver unit designed for use with 3D printer filaments, ensuring smooth operation and precise control over the printing process.

This upgrade makes printing flexible filament easier on the MakerBot Smart Extruder +. I conducted some initial tests with a MakerBot Replicator+ at standard resolution (0.2mm), using flexible filament shore 45D, which were successful. I even tested...