ultimaker 3 feeder 3d models

For assembly instructions, please refer to the original design created by Robert at https://www.youmagine.com/designs/alternative-um2-feeder-version-two#!design-information. To assemble this design further, you will need to attach the yoke to the...

It rotates the feeder so that the knurled side of the filament doesn't rub against the bowden tubes' side.\r\n\r\nMake sure your filament reel is no larger than a typical 1KG reel, as the new position of the feeder stepper blocks part of the reel...

Having tested Pit3k's feeder end bowden clamp, I noticed significant vertical play during filament extrusion and retraction. To resolve this issue, I combined the model with Helmforest's bowden bracket for a more stable result featuring no movement...

Introducing a replacement for the original wooden extruder gear, compatible with both Ultimaker Original and Ultimaker Original+ printers. Previous designs were unsatisfactory due to tooth profile inconsistencies or difficulty in fastening stepper...

View the groundbreaking design by dmols on Youmagine, showcasing a unique Ninjaflex Geared Ultimaker 2 Feeder.

External feeder for Ultimaker 2 attaches to top of printer, reducing Bowden tube length by about 30%. This setup makes printing flexible materials easier. ...To install, swap out standard case screws with longer M3x20mm versions; the originals won't...

A New Feeder for the Ultimaker 2. Other options work as well, but you can't easily fine-tune them via the small screw. ...The tubing holder was also a major issue there.

The original setup from Ultimaker had too much Bowden tube with a curved path, causing the flexible filament to compress and create excessive friction that prevented it from passing through the print head successfully. Furthermore, the feeder design...

This feeder and filament guide suit the Ultimaker 2.The pinching pressure of the filament can be adjusted thanks to a clamping screw. A latch and a hook allow to quickly remove the filament. Two aluminium tubes guide the filament in the feeder for...

This feeder and filament guide suit the Ultimaker 2.The pinching pressure of the filament can be adjusted thanks to a clamping screw. A latch and a hook allow to quickly remove the filament. Two aluminium tubes guide the filament in the feeder for...

This adapter spacer frame is essential if you want to fit the Chinese Ultimaker 2+ feeder to the Ultimaker 2, as some stepper shafts are too long on certain Ultimaker 2 models. Instead of cutting the shaft, which can be a bad idea, use this adapter...

External UM2 feeder with holder for the Ultimaker 2 case. ...They mount ontop of the UM2 and reduces the lenght of the bowden tube around 30% which might make it easyer to print flexible materials.</p> <p>To mount it you have to replace the existing...

I Accidentally Broke This Original Part of the Ultimaker 2+ Extended Filament Feeder. ... The Model Has Been Precisely Measured, But I Had to Print It at 110% Scale in ABS with a Temperature Setting of 255°C, Alongside the Board Being Kept at a Steady...

Inspired with adaptations from IRobertI "Alternative UM2 Feeder - version two" https://community.ultimaker.com/topic/11495-alternative-um2-feeder-version-two-about-robert/ -The same motor is used replacing the pinion gear with a "Feeder Knurled Wheel...

However, when I purchased conductive filament, I encountered a major obstacle: the feeder system of the Ultimaker series cannot accommodate 1.75 mm filaments. Buying new kits was prohibitively expensive, so I took matters into my own hands and came...

When I buy conductive filament, I faced with a situation that feeder system of the Ultimaker series are not supporting 1.75 mm filaments. Buying new kits was expensive. So I decided to solve this problem for my big goal and come up with this...

Locking them is important to prevent the smaller tube from being pushed up from the force of the filament feeder.\nThe hot end components (Olson Block, Peak, and Tips) have been replaced by ones designed for 1.75 mm filament.\nPrint Settings\nPrinter...

To install, remove the original clamp, then disassemble the feeder mechanism from your Ultimaker by unscrewing components. Replace the old clamp with the printed riser, assemble the mechanism back together, and secure the cap and cone on the bowden...

Settings to start with: I used clear Ninjaflex on UMO+Nozzle temperature 242°CBed temperature 50°CFan offPrint speed 25 mm/s (constant for everything, including infill)Gap speed 250 mm/sRetraction offLayer height 0.15 mmWall thickness 1 mm (top,...

The Ultimaker 2 Extended came with a 2.85mm diameter filament feeder/extruder, but using 1.75mm diameter filament resulted in many failed prints due to its brittle nature near the end of the reel. To overcome this issue, I've created a collection of...

I fabricated these components to decrease the gear ratio on my Ultimaker to a value of 3.75:1, which is lower than its standard setting of 6.125. ...This adjustment enables complete silence during retraction operations when combined with...

A double-helical (herringbone) gear set is presented for the default Ultimaker filament feeder, which may operate more quietly than the standard gears due to their rolling action. This design has proper bending of teeth, particularly on the smaller...

I designed these gears to lower the gear ratio for my Ultimaker to a precise 3.75:1, reducing it from the default setting of 6.125. As a result, the retractions become completely silent when combined with SilentStepSticks stepper drivers and operated...

This feeder was largely based on the "mother of all UM2 feeders" at youmagine; https://www.youmagine.com/designs/alternative-um2-feeder-version-twoedit 1/2015. I recently updated it with a bit more mass around the bearing wheel to guide flexible...

Part #9 of the Ultimaker 2 Extrusion upgrade kit is located here: https://ultimaker.com/en/resources/19641-installing-the-extrusion-upgrade-kit. The two end holes do not line up perfectly due to my inability to find the necessary drawings, but I was...

I'm creating an Ultimaker from acrylic, but unfortunately, I managed to break this crucial piece so I fabricated a brand new one within Alias to successfully print with my more compact 3D printer, here it is!

The my original feeder model is also posted there, along with various adaptations (my original feeder, http://www.thingiverse.com/thing:378939), including an improved version inspired by "the Mother of All UM2 Feeders"...

Based on a request from Catohagen, I developed a new version of my previous double helical feeder gear mod that features straight teeth. You can find the original as well as the knob for this modification on Thingiverse at...

I'm not a fan of having crucial parts located at the back where they're hard to access, like with the Ultimaker. It also wouldn't fit well into my narrow cabinet if it were much larger. ...So, I flipped the extruder section around and attached it to the...

I designed these gears specifically to minimize the gear ratio for my Ultimaker setup. The result is completely silent retractions when paired with SilentStepSticks stepper drivers, assuming a speed of less than 20mm per second. To get optimal...