ultimaker 3 feeder assembly 3d models

Spool holder for UliMaker 3, S5 and S7.Supports one 750g spool plus one 2.2Kg Spool.Fits perfectly on the printer with the original NFC sensor and bottom part.Prints in two parts, with 4 alignment pins.

I decided to build a new print bed out of a nice 6mm aluminum sheet, incorporating nearly plug-in 3-point bed leveling. I finished replacing my acrylic bed some time ago and I'm absolutely thrilled with this setup as it requires not too much space,...

It measures 3/32" thick and comes in a compact 12" x 12" size, all for about $5. Consider investing in a larger sheet if you need an extended version. To create the door, drill a .109 dia hole and tap it with a 6-32 thread, approximately 1/2" from...

4th November 2013 Inserted two newer versions, 1.2 and 1.2a, specifically for Hero 3 users; revised to feature thinner walls, requiring less material, with experimental versions 1.2B/D incorporating tabs to secure the cover in place better using an...

aa

aa

I adjusted the motor's direction with that, so now the spool is situated behind my printer. If you've got a wall at your back like I do, you can attach the spool holder to it right behind the printer - this setup improves airflow and keeps the...

One quarter (3-6 quadrant) of the case feeder plate has 2 bevels upside-down. ... Here they're fixed.

Cable Chain attachment for Ender 3 V2 filament feeder. ... This is a remix from https://www.thingiverse.com/thing:398515

When you need to print something, get ready for a treat - just take apart your printer, and as soon as you do, it springs into action with a loud "SPROING" sound. ...But the fun is over when you can't find that tiny piece.

A customized version of the 3D printable design found at http://www.thingiverse.com/thing:25436 has been created with the Customizer tool (http://www.thingiverse.com/apps/customizer/run?thing_id=25436). The specifications for this personalized model...

Building on the foundation laid by bkubicek's model, I crafted a customized gear wheel handle that delivers exceptional results. To achieve the finest surface finish, it is essential to print the design in the specified orientation and incorporate...

Customized version of http://www.thingiverse.com/thing:25436 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=25436 Instructions Using the following options: $fs = 1 $fa = 1 handleWidth = 20 armLength = 20 armHeight2...

A tailored version of http://www.thingiverse.com/thing:25436 was created using the Customizer at http://www.thingiverse.com/apps/customizer/run?thing_id=25436 with specifications including arm height 1 and 2 set to 13 and 17 respectively, handle...

2) Barriers were erected above these three "challenge" areas, the middle one being a simple vertical wall to limit feeding only from the front edge of the feeder, while two L-shaped corner walls protects the corners from feeding from the outer...

This fits on a feeder made from 3 inch pvc pipe. PVC "lid" fits over the top of this so the feeder can be closed at night. There are two versions, either you want this to fit inside a joint, or over a pipe section. ... Both allow you to fit a lid...

Place device on flat surface with back facing upwards. ...Secure firmly using standard mounting hardware.

I've augmented the size of the footprints to manufacture them with thermoplastic polyurethane material. ...It's advisable to produce two standard feet and two mirrored duplicates.

I engineered a set of straightforward circular feet with the aim of minimizing resonance. ...My goal was to decrease overall noise levels as well as instability during rapid movement.

I customized my UM3 Extended with custom wings, as the rear spool holder wasn't suitable for my setup. The printed wings you see in the picture were created on my MakerGear M3 IE using a .5 nozzle, .4 layer height, and a .6 layer width, all...

I experimented with the Um2 feet initially, but they didn't quite match up perfectly with the 18x18mm pads I had on hand, and unfortunately, they ended up scratching a bit of paint off my Um3. To rectify this situation, I created new feet that are...

I rectified the shortened rod problem, eliminated the section behind the pulley spacer to implement a minus 7mm design. ...Still require the base, pulley, and nut from Didierkl's original project.

The U3 print heads neatly snap into place within a conveniently located holder that is securely attached to the side of the U3 printer, keeping them readily accessible and at your fingertips for effortless maintenance and handling.

This handy gadget serves as a convenient storage system for idle print cores near printers, keeping them organized and easily accessible. Its straightforward design ensures that printing is virtually flawless due to its simplicity. I'm currently...

Safety Clip Secures Fan Door in Place During Printing Even When Magnets Lose Adhesion.

I'm proud to show off my latest creation - a door hinge designed specifically for use with 3mm plexiglass. The hinge features strategically placed mounting holes that I had initially planned to utilize, but ultimately ended up bonding the door...

Creality Ender 3 spool holder assembly