ultimaker 3 extended door 3d models

Extended by 5 mm compared to the original and reduced the terminals. ...This way it can accommodate larger coils with a minimum of additional space</p>

Extended fan ducts to work with after market hot ends like Micro Swiss. ... There is a 4mm version and 6mm version.

The level bubble itself was only 38mm wide, so I decided to extend the bubble slot and eliminate the curve. This way, the edges of the slot will perfectly align with the edges of the bubble, ensuring a straight reading. In my particular case, there...

... me, please feel free to <a href="https://www.printables.com/messenger/new/6231">message me</a>. &nbsp;I'm always willing to discuss my models, your ideas, 3-D design, and 3-D printing.ExploreCheck out my other models here on Printables.Com.&nbsp;

I needed an extended barrel to test my T238 tracer unit, so i remixed one Havent printed it yet - Will do so later on. ... Inner diameter is 17mm Outter diameter 18,90mm Should fit most attachments.

Have just extended the arm for the camera as i had stiffer springs and a glass bed it would just slightly hit the camera. ... Will still need the original files from jbkuma just replace the arm with this one

... ... The extended fan duct makes sure that the part cooling fan is blowing directly below the hot end. Super fast and easy to print. No supports needed. I recommend using 2 M3x16 bolts for the spacers, and I used 4 M3x6 bolts for the fan. ...

... gauges are much larger. ...I removed the SD card reader holder and extended the body to make space for a feeler gauge holder. I also added slots for my tweezers and small scissors. ... Printed as the original, with supports angled at 80 degrees.

I remixed this thing to have more support for the laptop by extending the corners of it and also adding a "foot" underneath it to support the load so it isn't cantilevered only on two points. ...I also filleted some of the edges that are contacting the...

... involved in this project. This version extends beyond the x-axis to prevent the filament spool from obstructing it. ... A STEP file is included, allowing others to easily customize this design according to their needs (angle, extension, etc.).

I extended two of the legs to make this happen less. I only changed the end cap, so that's the only piece in this remix -- it's compatible with the stock arm. The arm and the end cap normally require quite a bit of force to mate! ...I recommend using...

I'm looking for a single 3-millimeter screw.

I wasn't happy with other solutions to 3kg spool holders for voron 2.4, and I had the space behind my machine to fit a 3kg spool directly, so this derivative was the best solution for me.The original design was extended by about 50 mm and can fit up...

The only thing needed are stepper motor cable extenders, which I easily achieved with a Dupont Wire Kit - four wires were all that was required, leaving plenty of extras on hand. ...To optimize filament usage, holes could be added through the block, but...

Extended Version of the Belted Extruder v3 for 1.75mm Filament Original Design: http://www.thingiverse.com/thing:1764551 This updated design enables use of a 200mm or longer GT2 belt, enhancing overall performance and reliability. Additionally, it...

Hence I extended the frame by 10mm. I also added a cutout for the part-cooling-fan-duct. There might also be a cutout for the hot-end required, but I printed mine without. I added the .scad and original .stl so feel free to tinker with it. ... ...

Remixed the squashball feet in this pack to be extended an extra 25mm so that I could fit larger drawers and also improve airflow. These I have removed the built in V slot holders as it can be difficult to install them if you extrude a bit to...

I've experienced two severe crashes since installing these extended feet, one where my drone dropped 30 meters from a spinning motion onto a roof and crashed to the ground. Thankfully, they protected the drone well but were broken after impact. The...

I like fandabrac's 2019 remix for E3 printers a lot because it leaves 2.5 inches of headroom above the printer but out of a surplus of caution I modified the top corners of the fandaabrac remix to extend the leg supports and also offset the mounting...

The original holder was not wide enough (65mm) to accommodate my standard roll size (3"). ...Fortunately, I can use a replacement with the same thread as the original M30x1.5.

This sleek cover safeguards the left and right passive radiators of the JBL Charge 3, ensuring smooth movement even during intense use. ...Its unique design allows for unobstructed travel of the radiator, preventing collisions between the two...

The original housing was woefully undersized at 65 millimeters, rendering it incapable of accommodating my generously sized 3-inch rolls. ...Happily, the same thread as the original M30x1.5 is employed.

... Drive. Printing: Infill should be 50% or greater Recommended printing in high temp filament 1 Hour 5 Minute print on the Ender 3 Pro W/Support Best printing method is to print part upside-down like in picture w/support touching the build plate.

I've taken part of https://www.thingiverse.com/thing:4107156 and created a remix featuring the STEP file shared by @drewzh for the Ender 3 pro case, adapted specifically for the Raspberry Pi 4 with dual fan setup. ...A dual fan option previously...

A Tinkercad edit of the probe relocation baseplate for the Ender 3 S1/Sprite extruder. With this I have moved the probe location further left a little bit in order to give some space for different fan ducts, such as...

Remix of part of https://www.thingiverse.com/thing:4107156 As @drewzh kindly shared the STEP file for the Ender 3 pro case, I have created a version for the Raspberry Pi 4 with dual Fan setup. There was a dual fan option available, but only for the...

Clax's design at Thingiverse (http://www.thingiverse.com/thing:168750) inspired me to modify it for my Antec P182 case, as I needed the 3.5 HDD mounting holes to fit the drive bays. Check out my adapted version here! ...

... design. ...The ones I own have a 25 mm shaft and a 3 mm head. ...Another issue I've encountered was that the head would rub against the side of the printhead.The solution was to bring the bracket 5.25 mm out, so there is enough room for everything.

Place device on flat surface with back facing upwards. ...Secure firmly using standard mounting hardware.