ultimaker 3 extended door 3d models

I required a fan duct that extended down to where my nozzle landed after swapping out my Microswiss unit. After testing six different options, I couldn't find one that fit perfectly so I took control of the situation myself. I'm satisfied with the...

I required a fan duct that extended down to where my nozzle landed after my Microswiss upgrade. After testing six different models, none fit perfectly, so I decided to create one myself. I'm satisfied with the stock carriage and wanted to maintain...

To solve this problem, I designed an extended strain relief cover that keeps the bed wiring in place and prevents it from rising above the build surface. ...This new cover takes the place of the standard small trapezoidal cover and is secured with...

Extended it by 2cm at the stem to better accommodate access to the hooks. The bottom of the hooks have slightly problematic overhangs, so I enabled supports from build plate. --v2 Should not required supports I also printed this using adaptive...

I Utilize a Mag Release Drawing from Thingiverse, Which is No Longer Available on This Site. ... This Works Flawlessly on My Gen 3 G21 SF.

Just extended to fit my hotend . ...Print Settings Printer: YD3D Rafts: Yes Supports: No Resolution: 0.15 Infill: 25% Filament: Anything I can get my hand on cheap PLA Black Category: 3D Printers

I got tired of the larger filament spools falling off the default holder with my new Ender-3, so I made a longer one. ... It's 102mm worth of room for large spools and locks on using the default ring.

I modified CHEPs remix of the Ender 3 Side Spool Converter Bracket. The holder is now longer, giving the spools more space from the X gantry stepper motor, making them easier to attach and detach without hitting the stepper motor. ... It's not a work of...

This remix of a side mount for the Ender 3 lengthens the original design by a couple of centimeters, preventing filament spools from fouling on the stepper motor and/or cables. ...As a result, printer stability improves significantly with the spool...

This is an upgrade from the Simple touchscreen upgrade stand Ender 3 Pro. The stand has an extra hole to lock the extension on both sides.. The upper bold now is too short and has to be put on the opposite site of the three holes. It has to be...

... the spool is running out and is too light for side spool holder. There a not any complicated mechanisms, because they are not necessary here. I recommend to use <b>Nut_square</b> because of easy tightening. Note: Made for my 2018 Ender 3. ...

This is an upgrade from the 'Simple touchscreen upgrade stand Ender 3 Pro'. With the extension it is possible to change the inclination of the touchscreen for better visibility. The stand itself has an extra hole to be able to tighten the...

After installing a support rod kit on my Ender 3 v2 to help stabilize z axis wobble, I found that, if printing a very tall object, the roller guide with collide with the support arm. I took the original bracket and stretched it out to avoid...

Since I have my Ender 3 placed on some feet, I have some more height I can/need to use. Also changed the inlay for my convenience. Feet: https://www.thingiverse.com/thing:3349214 Place for: -1x 30A relay (1port) -1x 10A relay (2 ports) -1x 10A relay...

Since I have my Ender 3 placed on some feet, I have some more height I can/need to use. Also changed the inlay for my convenience. Feet: https://www.thingiverse.com/thing:3349214 Place for: -1x 30A relay (1port) -1x 10A relay (2 ports) -1x 10A...

The sample print shown in the images was printed using [UltiMaker PET CF.](https://ultimaker.com/materials/s-series-pet-carbon-fiber/) This part can be used to test the dimensional accuracy of the UltiMaker Y-coupler [which you can find...

... the holder a little to be able to nail it to a wall. ... I printed it standing as in the pictures, with a little bit of brim and support at the base just to help a bit (brim and supports add about 1g of material and 3-4 minutes printing time).

I'm going to create an extended battery door for the Nerf Barracade, allowing users to add larger batteries like LIPO packs. Check out this photo where I've managed to fit an 8.4v 2s LiPo pack and a LiPo alarm inside. My design is optimized to...

When I place the extended grab handle in the travel or closed position it was touching the #3 on the keypad. I made this bumper block to add about 7mm of space and cushion so it would not destroy the lock during transportation. Easily prints with...

The original expanded battery door can be found here: https://www.thingiverse.com/thing:4748014 The Battery Tray is remixed from the one by opcolu. I trimmed a few mm off of the tops of the walls at the end so that the expanded battery door could...

An expanded battery door for the Dart Zone Pro MK3, fits up to a 3S 2200mAh lipo battery.it should be printed with supports25/08/2023: Added a “plain” version to add your own decoration and a “Pro” version just for fun.08/09/2023: Fixed a hole in the...

... The car is divided into 51 objects for ease of animation, door opening, rigging, customization, and tuning purposes. Each object comes with a material channel and an additional UV-mapped channel optimized for light mapping or further texture work.

Door Latch-Part 3

Door Knob-3

<p>The Hinge design I've been using kept breaking, so I modified it to use M4 x 25mm screws for increased strength.</p><p>&nbsp;</p><p>Remixed from this design: https://www.thingiverse.com/thing:2494261</p>

You might wonder: "why so many pieces?" I thought that too. My original plan was simple, but it required cutting into the corners of plexiglass to level them with the printer's top side when using just the corners. That cover, however, was shorter,...

Head Mounting Attachment

This is a mounting bracket specifically designed to secure your PrintCores, allowing them to be conveniently attached to the side of your UM3.

A simple holder keeps the printcore securely in place near the printer at all times, except when it's in use. This holder needs to be screwed together using a simple bolt and nut. The holder clamps the core tightly, just like in the extruder...