ultimaker 3 enclosure 3d models

Crafted specifically for use with the Raspberry Pi 3, this enclosure serves as an ideal housing solution.

Ultimaker S3 Acryglas 19,5cm x 44cm x 5mm 2 Stück 19,5cm x 39cm x 5mm 2 Stück 45cm x 33,5cm x 5mm 1 Stück 21cm x 10cm x 5mm 1 Stück Ultimaker 3 Acryglas 19,5cm x 44cm x 5mm 2 Stück 19,5cm x 33,5cm x 5mm 2 Stück 33,5cm x 45cm x 5mm 1 Stück 15cm x 10cm...

This is enclosure for OpenSprinkler 3.2 master + DC or AC board. ...Enclosure was designed for board with higher LCD connector (8 mm instead of 4 mm) but could be easily changed in .scad and exported.

3-point levelling with magnetic ball bearings for Ultimaker printers involves assembling specific parts and attaching a nut bed, extension arms, and levelling bolts. Begin by removing the existing print bed and screws. Replace or use an acrylic bed...

Front Panel Design for the Ultimaker 3 Extended. Engineered Specifically for .093” Thick Plexiglas or Lexan Sheets. Optimized Dimensions for Seamless Installation. The Cover Can be Hung on the Side of the Machine When Not in Use. **Required...

Assemble your 3-point levelling before disassembling your print bed. Use printed relay fixture/clamp with a 12V and >15A power supply on a Prusa MK2 heated bed. Connect the thermal fuse in series to the heating circuit, taping or cementing it under...

When you use the automatic leveling of the Ultimaker 3, then the 'Finger' will collide with the remote shutter mount. Please stick the 'Finger' into the printhead mount AFTER the automatic leveling is done. The Remote Shutter: I found a small...

Start with the 3-point levelling parts (http://www.thingiverse.com/thing:84754) Obtain a Prusa MK2 heated bed and 12V and >15A power supply as per instructions in (http://www.headfuzz.co.uk/ultimaker-headed-bed). You don’t need the MDF sheet, we...

3-point levelling for Ultimaker with magnetic ball bearing. Print instructionsCategory: 3D Printer Accessories Summary 3-point levelling for Ultimaker with magnetic ball bearing. Instructions Required parts: 3x 7mm magnetic balls 3x M4 30mm socket...

This effect usually requires a script in Octoprint, but I wanted to achieve it without using that with my expensive Ultimaker 3. So, I decided to find a way to do such cool timelapse videos my own way. Here's a link to the video that inspired me:...

This configuration is necessary due to the Ultimakers' tendency towards back heaviness and the Sorbothane half-spheres' requirement for adequate loading to function optimally. ... These feet perform exceptionally well compared to other solutions I've...

The x-axis print head rod on my Ultimaker was sliding left and right. The solution I came up with is to use a stop collar and spacer on the far right. This is the only space available for an x-axis stop collar without interfering with the...

As the Ultimaker uses Dibond (aluminium sandwich with plastic in between) most double-sided tapes won't damage it but do secure it well. I used brass threaded inserts as this will allow me to screw off the m3 bolts easily without damaging the printed...

When tackling projects that involve aluminum or brass, consider utilizing a Shapeoko 3 electronics enclosure for optimal results. ...It's worth noting that my own Shapeoko electronics installation has been inverted, causing the cable holes to face...

Currently a work in progress. ...80-20 enclosure for my Shapeoko 3. ...Designed such that all of the required acryllic sheets can be cut from a single sheet of 4' x 8'.

This is an enclosure I came up with to house the main board and a Raspberry Pi Zero WH for my Ender 3 after updating to Klipper firmware. Klipper does not utilize the main board sd slot so I made a nice uniform front face. I also made the enclosure...

This is an enclosure I came up with to house the main board and a Raspberry Pi Zero WH for my Ender 3 after updating to Klipper firmware. Klipper does not utilize the main board sd slot so I made a nice uniform front face. I also made the enclosure...

For customization, set remove_shapes to 1, shape as 128, wall_width to 3, outside diameter to 150, filament density at 1.04, enable hollow design with filament diameter of 3, spindle diameter of 55, and inside diameter as 61. ...The resulting width...

To create a DIY printer modification, start by acquiring a 32x32 cm plate with a thickness of 2-3 mm made from acrylic glass. Place the necessary components onto the plate and drill holes in it for mounting purposes. When using "DoorHolder2" pieces,...

This subwoofer enclosure is tailored for a high-performance 3-inch subwoofer. It's perfectly matched to pair with our innovative modular sound bar system. ...The mounting holes are intentionally left blank, allowing users to easily customize and install...

... for LM2596 buck converters, such as this one found on Amazon. ...This enclosure slips neatly into the V-slot directly behind the electronic casing. Specifically crafted for use with the Ender 3, it will also fit snugly onto any V-slot extrusion system.

I DESIGNED THESE CORNERS SPECIFICALLY FOR BUILDING MY ENCLOSURE FRAME AROUND MY CREALITY ENDER 3 - SO I PRINTED THEM IN SETS OF EIGHT, FOUR LOWER AND FOUR UPPER CORNERS, USING 25MMX25MM ANGLED ALUMINUM PIECES THAT WILL BE COVERED ON THE INSIDE OF THE...

This is enclosure for OpenSprinkler 3.2 master + DC or AC board. ...Enclosure was designed for board with higher LCD connector (8 mm instead of 4 mm) but could be easily changed in .scad and exported. Print instructionsRafts: No Supports: No Resolution:...

To construct an enclosure for the Solidoodle 3, utilize 0.08" thickness acrylic sheets. The design also fits the SD 2. This is my first Thingi; I released it prior to testing because my printer isn't here yet and I wanted more knowledgeable...

This is an enhanced version of the existing Ender 3 enclosure featuring several key add-ons: 3 independent fans that enable precise temperature control, allowing each fan to be turned on or off as needed A control box equipped with a digital...

Collection of parts I needed to make an ikea lack enclosure fit an ender 3 pro. Many other listings claim to fit an ender 3 pro, but they don't. Modifications from the original design include: -Wider psu cable guide -Different psu mounts -Heatbed...

Enclosure for Ender 3 Double component ventilation Parts: 4 pcs threaded socket...

Enclosure for Ender 3 Double component ventilation Parts: 4 pcs threaded socket...

First take on an enclosure for a Speeduino v0.3.x board is up. The hardware required is four M3x50 cap screws and matching nuts. On December 7, 2016, the design was updated with better alignment and a version of the bottom that includes mounting...

I'm going to need some ABS 3D printed parts in an upcoming DIY go-kart series, so I decided to make an enclosure for my Creality Ender 3. Being unsatisfied with both the cost and quality of available options on the market, I set out to DIY my own...