ultimaker 3 calibration card 3d models

... with multicolor produces a lot of waste. ...I recommend printing multiple models at once. Don't miss out on exploring my other models here: https://www.printables.com/cs/@Jerryie/models WARNING: CHOKING HAZARD-Small partsNot for children under 3 years.

I use 3mm metal spools that don't fit on my printer's original spool and it causes prints to fail due to the material jamming in the core.

This is my take on the standard Ender 3 bed level calibration. Instead of relying on a piece of paper, this file is tailored to be used with a precise 0.1mm or 0.004" feeler gauge or shim stock. By doing so, all inconsistencies associated with paper...

Position the mount to facilitate the installation of the caliper for precise axis calibration.

The calibration tool is a sturdy frame with a clamp that snugly connects to the X-Gantry: Print two copies. Place one on the left side and one on the right side. Bring the X-gantry up until one side (ideally both) touches the top bar. If one side is...

This part tests the basic capabilities of a bed at a standard height and also provides a platform to calibrate the offset settings for dual extrusion prints.

The code in the .gcode file performs the following steps: 1-All axes are initialized (hommed) 2-The plate and extruder are warmed up 3-Retract the filament to prevent leaks 4-The nozzle rises to allow cleaning 5-Wait for the user to clean the...

... spit out your new steps/mm! Note, make sure to level your bed well before calibrating or else the Z calibration can be inaccurate. ... UPDATE 9-6-2019: Found a major error in the code, download again if you used the scripts prior to this update.

In this video, we demonstrate how to make the calibration of the CNC laser that we brought to you. Firstly, we made the calibration settings. Then, using the LaserGRBL program, we drew 2 sample drawings. We used the characters "LA CASA DE PAPEL" as...

This is a compilation of my individual calibration tests: 25 Degrees - https://www.thingiverse.com/thing:2361995 45 Degrees - https://www.thingiverse.com/thing:2363713 60 Degrees - https://www.thingiverse.com/thing:2363721 Calibrating the center can...

... locations. Allows you to attach a measuring tool (deep measurement, sliding ruler...) and measure physical movements of the axes precisely. A procedure with a .xls file is available for adjusting and calibrating step/mm values of axes X and Y

In this video, we demonstrate how to make the calibration of the CNC laser that we brought to you. Firstly, we set up the calibration settings. Then using the program LaserGRBL to draw two sample drawings. We used "LA CASA DE PAPEL" as a sample...

Don't forget to install magnets.Tip: replace your 42.3 mm Hotend PTFE tube (MK3S+, MMU2S) to prevent The Hook of Death.Assemble the extruder. Use Prusa guides for help.Install the filament sensor in its original place as MK3S+.Replace the...

... of the attached pics for explanation. Creality Ender 3 https://www.banggood.com/Creality-3D-Ender-3-V-slot-Prusa-I3-DIY-3D-Printer-Kit-220x220x250mm-Printing-Size-p-1278399.html?utm_campaign=t0002_1123036&utm_content=11033&p=DG23031123036201501P

... attached pictures for an explanation. Creality Ender 3: https://www.banggood.com/Creality-3D-Ender-3-V-slot-Prusa-I3-DIY-3D-Printer-Kit-220x220x250mm-Printing-Size-p-1278399.html?utm_campaign=t0002_1123036&utm_content=11033&p=DG23031123036201501P

The g-code files in gaaZolee's post did not seem to work properly in my Adventurer 3. So I tried using Cura with config files for the printer posted on GitHub to convert the STL. Cura has some handy g-code editing scripts to speed things up. So,...

This is a remix of [AletheianAlex](https://www.thingiverse.com/AletheianAlex)'s Creality Ender 3 alignment prints". I modified the model, added an extended port on the bottom of the mainframe, and adjust the depth of the long socket hole. The...

Bill of Materials: 1) Raspberry Pi Zero W; 2) Pi Camera; 3) 2 pairs of 20mm M3 screws and nuts; 4) all these 3D printed parts; 5) memory card with an installed surveillance platform of your choice (tip: OctoPrint works well, even if you use only the...

This nut can be used with a commonly available 3/8 inch push-fit bowden connector. ...Slots in the Ultimaker extruder and the push-fit screws in tightly.

A typical 3/8 inch push-fit Bowden connector is compatible with this nut. ...It fits snugly into the slots of an Ultimaker extruder, secured by screws that push-fit in tightly.

In my dial gauge modification, I adapted Uga's design for a 3/8" shaft. ...Initially, it was a bit snug, but I resolved that issue. To install an M3 bolt on the side opposite the Ultimaker head, follow these instructions.

Key components used in this design include: * Raspberry Pi Model 3 B * 5" LCD HDMI Touch Screen, 800*480 resolution for Raspberry Pi 2/3 * Repetier Server Pro software * OctoPrint * Raspberry Pi 2&3 compatible 800x480, 5-inch XPT2046 display case...

File for Calibration of First Layer on Ender-3

A problem that I encountered was that the retractable cord attached to the card holder wasn't strong enough to retract and hold the card holder with all the cards. I thought about buying one of those Aliexpress retractable cords but they are big like...

These alternatives can be found here: https://www.youmagine.com/designs/ultimaker-laser-cut-drawings--2 For more information about the Ultimaker Original, visit: www.ultimaker.com The Ultimaker Original is available for purchase both as a complete...

I unfortunately have to carry three ID cards with me so I remixed the two card version by EUCGUY to create a center space and to beef up the lanyard connection point a bit. The center space works as a friction fit so you may have to slide your card...

I unfortunately have to carry three ID cards with me so I remixed the two card version by EUCGUY to create a center space and to beef up the lanyard connection point a bit. The center space works as a friction fit so you may have to slide your card...

This support accommodates three SD cards, securely fastened with a single 3mm screw. ...For optimal placement, I suggest positioning it at an angle, parallel to the side.

... Alternatively, check out my separate design for four SD card slots (http://www.thingiverse.com/thing:474057). ...I suggest printing these supports in PLA, utilizing Makerware's standard settings: 10% infill, two shells, and a layer height of 0.2mm.