ultimaker 2 filament guide for 90 degree rotated spool 3d models

Small modifications were made to the excellent low friction spool holder for the Ultimaker 2. Recently, another filament supplier was used that utilized 9cm wide spools which wouldn't fit. To accommodate this, a longer core was created (with a length...

I wanted to turn the spool holder 90 degrees to have better filament feed to the print head. Had done the smae on the previous printer and worled out well. Since I never use a filament sensor this is for me the best position. you need 1 extra t-nut...

The link is https://www.youmagine.com/designs/filament-cleaner-for-ultimaker. To clean filaments, you can use a sponge; it offers low friction and no printing issues. I'll test it further and may tweak the design later. The OpenSCAD file allows easy...

A fusion of "Heavy duty filament spool - for mendel by watsdesign" (http://www.thingiverse.com/thing:11447) and "Snap-In Mendel Filament Guide, with diagonal slot by toomanyplugs" (http://www.thingiverse.com/thing:11521) spurred my interest. I...

After searching for one compatible with my Ultimaker, I designed a simple version using OpenSCAD. The sponge causes minimal friction, so there shouldn't be any issues with printing or retraction. I'll monitor the results and possibly modify the...

There is space for 2 magnets each side to better guide the saw. This is why this model is better than the rest out there: It can be used both ways It provides space for clamps. So your cuts will not be wobbly and you can 100% concentrate on sawing...

This is a spool holder filament guide accessory item that can be attached in the inner side of the spool holder, pass the filament through and prevent any tangles due to loose filament on the spool. This is quite useful especially when the spool is...

... at all times and adds more stability to the structure. Print Settings Printer Brand: Ultimaker Printer: Ultimaker 2 Rafts: No Supports: Yes Infill: 50% Notes: Using Cura. ...Fast 50% infill Skirt Support build plate only Printed in 5.5 hours

... Filament guide - https://www.thingiverse.com/thing:4288768 Spool mount - https://www.thingiverse.com/thing:4459319 Just made a revision to make the spool mount slanted to use gravity to hold the spool in place. ...will post pic when print is done.

This design features a 90-degree base for firmly anchoring a 3D printer at the bottom of an enclosure. Two strategically placed throughholes on one end allow screws to secure it, while the other end remains unscrewed. ...The intention is that each foot...

... facilement le filament dans mon imprimante Ultimaker 2+, sans y aller à l'aveugle. ... J'ai trouvé un guide filament mais pour l'Ultimaker 2. ...Comme il n'était pas adapté, j'ai retravaillé le fichier STL pour ne conserver que la partie entonnoir.

... facilement le filament dans mon imprimante Ultimaker 2+, sans y aller à l'aveugle. ... J'ai trouvé un guide filament mais pour l'Ultimaker 2. ...Comme il n'était pas adapté, j'ai retravaillé le fichier STL pour ne conserver que la partie entonnoir.

In the process of dismantling a 3D printer, I wanted to integrate the Universal Ultimaker 2 Spool Holder seamlessly into it, prompting me to design a screw mount for compatibility. This custom mount is specifically engineered to utilize M5 screws.

As a result, the build plate is often warped due to the cables, prompting me to create a cable guide wall for protection. ...This modification ensures that the cables are safely secured and out of harm's way, preventing any further damage to the...

This spool holder will hold a spool with a body up to 76mm. The Innofil/Ultimaker spools do not fit this holder, but it is as easy as the original to swap out. I took the original file frombhttps://www.youmagine.com/designs/spool-holder-xl (Roland...

This front mounting filament guide is remixed off the original Ultimaker part: https://www.youmagine.com/designs/ultimaker-3-spool-holder It simply clips onto the front of the spool holder - the cable cover cannot be used with this guide. ...The white...

This front-mounted filament guide is a remixed version of the original Ultimaker part: https://www.youmagine.com/designs/ultimaker-3-spool-holder. It clips directly onto the front of the spool holder - users cannot utilize the cable cover with this...

The standard Innofil/Ultimaker spools do not fit this modified holder, but replacing them is just as effortless as swapping out the original spools. ... I started by utilizing the original file provided in the acknowledgement section (Roland Benner)...

A Customization for My Remix Filament Spool Floor Mount http://www.thingiverse.com/thing:1625898 Print Settings Printer Brand: Prusa i3 mod Printer: RepRap Rafts: Doesn't Matter Supports: Doesn't Matter Resolution: 0.1 Infill: 50 Notes: Printed with...

... heavy spool loads. ...PLA is not recommended as it lacks the necessary "spring". ABS or PET materials, such as Colorfabb XT, are preferred alternatives. Additionally, the Spool Holder fixture and Filament Guide fixture require support during printing.

Ultimaker 2 users rave about the ingenious T-glase filament holder designed by Taulman, a true game-changer for print quality and reliability. ...The versatile T-glase system effortlessly adjusts to fit all Taulman filament profiles, providing precise...

A compact, 90-degree antenna bend guide designed specifically for use with 2.5mm coaxial cables. ...This adaptable accessory ensures a seamless connection between your antenna and coaxial cable, promoting optimal signal transmission and reception in...

I needed a spool holder for the Rigid Ink 1kg spools since they feature a larger hole (54mm) and a wider body (74mm). This spool holder will securely hold a spool with a body up to 76mm. The Innofil/Ultimaker spools do not fit this holder, but it is...

Simple and Effective Guide to Using the Stock Spool Holder's Filament Guide System.

The Ultimaker spool holder got a serious upgrade thanks to this adapter that comes with screws, making it easy to attach straight into an IKEA enclosure without any extra hassle.

I adapted a design for a UM2 filament holder and customized it to accommodate the Taulman T-Glase filament spools perfectly.

I needed a filament guide for my direct drive printers since I print straight from my filament dryers.Bob1599 made a nice spool holder that fit my all machines, but I needed something to keep the filament up and controlled.So I remixed his design in...

Guide to Curving a 2.5mm Coaxial Antenna Cable 90 Degrees Without Kinking It. Curving a 2.5mm coaxial antenna cable 90 degrees is a delicate process that requires some finesse to avoid damaging the delicate inner components or kinking the outer...

Here are the parts needed: * 2 x M3 x 25 * 2 x M3 nut for aluminum extrusion * The rest of the parts are the same as Robert's BOM. Note that this design accounts for the 3mm Acrylic panel between part and aluminum extrusion. You may need to add more...

Designed specifically to work seamlessly with 1.5-inch core diameter filament spools, this product is not intended for use with 30mm models. ...However, users familiar with Inventor 2015 will find it relatively straightforward to modify the provided ipt...