ultimaker 2 feeder 3d models

The my original feeder model is also posted there, along with various adaptations (my original feeder, http://www.thingiverse.com/thing:378939), including an improved version inspired by "the Mother of All UM2 Feeders"...

You might want/need to print the small gear as well, so that's included but it's a straight copy of the original from the ultimaker github https://github.com/Ultimaker/Ultimaker3/blob/master/1969/1969-G/1969-G.STEP which is licensed under...

This feeder and filament guide suit the Ultimaker 2.The pinching pressure of the filament can be adjusted thanks to a clamping screw. A latch and a hook allow to quickly remove the filament. Two aluminium tubes guide the filament in the feeder for...

This feeder and filament guide suit the Ultimaker 2.The pinching pressure of the filament can be adjusted thanks to a clamping screw. A latch and a hook allow to quickly remove the filament. Two aluminium tubes guide the filament in the feeder for...

Everybody's had their shot at creating an extruder feeder for the Ultimaker 2. I've been using a customized version for a while, and now there's even an UM2+ upgrade available. So why another one...? I personally like the Bondtech concept where the...

Make layer time like 20 seconds, adjust the part with breakaway knife and 3mm drill bit. ...Put inside the feeder 1 or 2, done. You can now print flex with less jamtastic experience. ... Hey Ultimaker, for 3 grand these should be default.

This ingenious adapter plate makes it a breeze to attach your Ultimaker 2 plus feeder to an original UM2+ machine. Simply position the adapter between the plastic and metal components of the feeder, and you're ready to roll! With this clever setup,...

Install the Ultimaker 2 feeder on your existing Ultimaker 1 machine. ...Consider pairing it with Robert's UM2 Alternative Feeder, a design available at Youmagine: https://www.youmagine.com/designs/alternative-um2-feeder-version-two

... and two long M3 screws & nuts. While you may need to recalibrate the feeder motor due to the new gear system's extrusion rate (95mm when swapping with stock Ultimaker gearing), it functions as a direct replacement for the standard feeder system.

... 1:1 printing. Uses stock Ultimaker feeder components, rollerblade bearing, two extra 3x30mm screws, two small springs, and an 8mm bolt/tubing. Post-processing needed on end-stop; file off overhangs for proper hook attachment. ...Easy assembly.

Upgrade your Ultimaker's feeder with this 3D printable part, which significantly reduces friction caused by stock components. Easy to assemble and install; simply replace the original part with the provided roller (10x6x3) for enhanced filament feed....

I designed it specifically for the new feeder upgrade from Ultimaker, replacing the delrin ring entirely. Use at your own risk, though - test it out first to ensure compatibility with your printer. To install, make sure the infill is 100%. The fit...

The upgrade includes printable modifications to all three components while maintaining fidelity to the original Ultimaker design. To implement this, you'll need a 6mm ID, 10mm OD, 3mm wide bearing, available for £1.99 on eBay. This modification...

Filament is devoured by the feeder wall, then buries itself in the wood as it slips away, rendering the feeder wheel powerless to grasp and convey it.

A malfunctioning feeder clip in my print has prompted me to seek a replacement. ...The clip is specifically designed for the knurled drive bolt kit - version 3, and it was used with a 25% infill setting.

My new bearing plastic has arrived, and I've successfully crafted it to replace the broken original on my Ultimaker printer. ...The design features 100% infill for added stability, and I've omitted any scaling to ensure a seamless fit.

Upgrade from Ultimaker's standard delrin ring. Proceed with caution, as it may affect your printer's performance. Assemble with a tight fit; adjustments might be necessary based on your printer's specifications. ...Consider increasing the outer diameter...

Instructions: Once printed, take apart your old feeder and use a standard nut - not one with a lock thread - and plop the bearing on. Away you should go. It's a little tight getting it in there, but it works nicely. Make sure to print it with 100%...

Follow the instructions carefully: disassemble your old feeder, use a standard nut, place the bearing, and ensure proper tightening. Print the modified model with 100% fill for optimal strength. ...To check movement during printing, add black dots on...

Ultimaker Original Plus Main Feeder Body Only

... ... Print Settings: Printer Brand: Ultimaker Printer: Ultimaker Original Rafts: None at all. Supports: Not a single one is needed. Resolution: It's precisely 0.2 millimeters. ... Infill: A solid forty percent of the print is filled in with material.

I took inspiration from Frederik Brückners design on Youmagine, specifically his Ultimaker Original or Plus Feeder Damper. I also drew from ataraxis' spring socket design to create this feeder damper. To print the parts, use PLA for Print...

Print Settings Printer Brand: Ultimaker Printer: Ultimaker 2 Rafts: No Supports: No Resolution: 0.4 is fine Infill: 100% Notes: This part only needs to withstand the pressure of holding the weight of the stepper motor and must be strong enough to do...

Problem:  Solution:  See how I made...

It's no longer necessary to use Ultimaker's proprietary 2.85mm filament as it supports 3mm filaments without deformation. Combine this feeder with a stock bowden setup for seamless printing without jamming concerns. However, the OpenSCAD file design...

Upgrade your Ultimaker 3D printer with Wheel2 or Wheel3, my innovations for Mk2/Mk3 filament feeders. Wheel3 features larger holes and a support cylinder to simplify printing. Print at 0.2mm using gold PLA at 210°C, sourced from MoonCactus' design...

Strain relief for UMO feeder prevents over-bending of filament as it enters the feeder, ensuring a smooth and efficient printing process. The bracket secures through pre-existing screw holes in the feeder, providing a sturdy base for the strain...

Having tested Pit3k's feeder end bowden clamp, I noticed significant vertical play during filament extrusion and retraction. To resolve this issue, I combined the model with Helmforest's bowden bracket for a more stable result featuring no movement...

Assemble the primary components of your Ultimaker 2+ using the provided .STEP file as a guide.

Introducing a replacement for the original wooden extruder gear, compatible with both Ultimaker Original and Ultimaker Original+ printers. Previous designs were unsatisfactory due to tooth profile inconsistencies or difficulty in fastening stepper...