ultimaker 2 extended 3d models

http://www.thingiverse.com/apps/customizer/run?thing_id=215386 Print Settings: Printer Brand: Ultimaker Printer: Ultimaker 2 Resolution: .2 Infill: 100% Notes: Bottom Layer: .3 mm Wall Thickness: .8 mm Top/Bottom Thickness: 0 mm Instructions: Using...

... in the table plate. You need M6 20mm screws to mount the rubber foot to the holder. A nut is not needed but I integrated a place for a one in the design. If you use a nut the screw must be 25mm long. Also fits Ultimaker Original plus and Ultimaker 2

An alternative Filament guide for the Ultimaker 2 with beared wheel. No more ticking sounds from the feeder... ... Instructions Print at 100% All you need is a bearing with a 12mm hole, 28mm outer...

I was unimpressed by the stock aluminum fan shroud and 40mm fans that came with my Ultimaker 2+, so I decided to create a custom design using Autodesk Inventor.

The ultimate 3D printer, the Ultimaker 2, features a dual-fan setup that I greatly admire, and I'm keen on replicating this design in my RepRap. ...It's designed to accommodate three 30mm fans for optimal cooling performance.

The Ultimaker 2 Z Shaft Bottom Cap is a crucial component of the printer's mechanical system. ...It serves as a protective covering for the Z-axis shaft, ensuring smooth operation and preventing damage to surrounding components.

A New Feeder for the Ultimaker 2. Other options work as well, but you can't easily fine-tune them via the small screw. ...The tubing holder was also a major issue there.

The device attaches itself to any spool holder designed specifically for the Ultimaker 2, placing it securely atop the framework. ...This versatile component can easily be repurposed as a support system for an additional extruder unit.

The frame accepts any spool holder designed for the Ultimaker 2, allowing it to be mounted directly above. ...This versatile accessory is also suitable for adding a second extruder.

The device is designed to secure any spool holder compatible with the Ultimaker 2 directly onto the framework. ...This versatile tool can also serve as a holder for a secondary extruder.

This upgrade links the original Ultimaker 2+/3 extruder to a Bowden tube on the filament insertion end. The printed component swaps out the top cover of the standard extruder. ...You'll also require an additional Bowden coupler for installation.

External feeder for Ultimaker 2 attaches to top of printer, reducing Bowden tube length by about 30%. This setup makes printing flexible materials easier. ...To install, swap out standard case screws with longer M3x20mm versions; the originals won't...

A moderately detailed ultimaker 2, 3D printer. Use as a scene filler or center piece. ...(Not detailed enough for exploded views but rigging and simple animations will work perfectly)

Here is the rewritten text: We're creating a fast-paced solution to attach a Raspberry Pi camera module securely onto the door of an Ultimaker 2+ Advance c 3D Printing Package.

Upgrade Your Ultimaker 2+: A Game-Changing Fan Shroud Refresh Revamp the Hole Blower with a sleek new design, boosting airflow by 25% and reducing noise pollution. Add a high-capacity Wiring Slot to ensure your fan wires are neatly secured,...

The adapter ring clicks securely onto the 57mm NuNus filament reels, instantly making them usable with the 50mm spool holder found on the Ultimaker 2. To achieve this compatibility, simply print two of these rings and snap them snugly onto either...

... under an incorrect license! Here's How It Was Created: This design wasn't created by me - instead, I converted the STEP file from the Ultimaker 2's Github repository into an STL using DesignSpark Mechanical, which is completely free to use.

Flat feet to put under Ultimaker 2 to reduce noise. These feet provide a flat surface that is then easier to soften to isolate vibrations. I used some 3M "Multi Purpose Sealing and Insulation Tape" under the feet for soft cushioning. Also printing...

Print Settings Used: Printer Brand: Ultimaker Printer: Ultimaker 2 Rafts: No rafts were used. Supports: No supports were needed. Resolution: A resolution of 0.2mm was chosen for the print job. Infill: The infill density was set to 20%. ...Notes: These...

This fix has been modified from an original design for the Ultimaker bowden clamp but I've created a specific version for my Ultimaker 2. My bowden tube keeps coming loose during prints so I developed this to prevent future issues (and it's far...

The top part of my Ultimaker 2's print-head snapped off (I'm convinced that over-tightening the thumb-screws was my mistake). Thankfully, a replacement-part is now available, which I had designed from scratch using Fusion 360. Its slightly altered...

Rev.1 (Horizontal) Lüfter Kühlung für das Controller Bord Ultimaker 2/2+. Vier Schrauben für den Lüfter mit Kappe M3, 25mm lange und zum Befestigen M3, 30mm lange Schrauben. Passend für 40mm Lüfter Der 24V ist angeschlossen an den J20 Stecker...

The design is optimized for use with M5 screws, and it's only intended for experimentation if you have a spare Ultimaker 2 Spool holder you want to mount on another printer or in a different location. ... Print Settings: Printer Brand: Prusa i3 Printer:...

For more details, check the links provided below: thingiverse.com/thing:811271, youmagine.com/designs/ultimaker-2-aluminum-extrusion-3d-printer, and 3dprint.com/66742/ultimaker-2-aluminum-extrusion/. The Solidworks assembly is accompanied by a Bill...

... necessary to print the holder of ASA also. The cable chain in my Ultimaker 2+ is made of PLA and resisted the high ASA temperatures (255°C nozzle 90°C bed) very well. ... Update 2018_09: I printed with ASA and the cable holder didn't deform a bit.

... like ASA. As a result, I am unsure if printing the cable holder from ASA would be necessary or beneficial. My Ultimaker 2+ has a cable chain made of PLA, which held up well during prints involving high-temperature ASA (255°C nozzle and 90°C bed).

To solve this issue, we completely re-engineered a new version of the spool holder, one that's an impressive 70mm long and specifically designed for use in 3D printing.\nPrint Settings\nPrinter Brand: \n Ultimaker\n \n Printer: \n Ultimaker 2 Plus\n...

... able to attain with a single, solid piece. **Print Settings** * **Printer Brand:** Ultimaker * **Printer Model:** Ultimaker 2 * **Rafts:** Yes * **Supports:** Yes * **Resolution:** 0.4 mm layer thickness, 0.1 mm infill gap * **Infill Density:** 20%

Protoype de fixation de cable de type ultimaker

I've created two versions: one based on the original design for the Ultimaker 2 heater, with added mounting holes for the MK2b heater, and a second version designed specifically for my custom heater plate. This second version features all mounting...