ultimaker 2 enclosure 3d models

This works with Ultimaker 2 and 3 printers using the existing spool holder. This is a lateral spool mount designed to make it easier to use large reels. ...Note that if you're operating an Ultimaker 3, it will block access to one extruder, but still...

If you want to put an Ultimaker 2 print head on an Ultimaker original you will need a way of mounting the thermistor board onto the head. That's what these two parts are for. The round washers create a mounting for the board. Put one beneath the...

This E3D conversion is optimized for Ultimaker 2, Ultimaker 2+, Ultimaker 2 Extended, and Ultimaker 2 Extended+. The E3D printhead carriage may also be suitable for the Ultimaker 2 Go and the Ultimaker Original, but those variants have not been...

I've recently upgraded the rear section of the LCD enclosure for the Ultimaker clone designed by denisc, giving users direct access to their LCD controller's SD card slot.

I just updated the back part of the LCD-enclosure for the Ultimaker clone by denisc - now you can access the SD-card slot on your LCD controller. Print instructionsCategory: 3D Printer Parts

I created a camera holder for the ESP32-Cam module to mount on an Ultimaker 2+

Kit Required to Mount E3D V6 or Similar Hotend on Ultimaker 2/2+ Family. ... You'll Need to Get Started in Just a Few Days, as We're Working on a Comprehensive Installation Manual.

This is a Remix of the Ultimaker 2 / 2+ Cam Holder by conny_g I made a remix for connecting my Action Cam to my Ultimaker 2+ 3D printer. I pasted the baseplate STL file into Fusion 360 and edited it. For my action cam, I drew a bracket that can be...

You might want/need to print the small gear as well, so that's included but it's a straight copy of the original from the ultimaker github https://github.com/Ultimaker/Ultimaker3/blob/master/1969/1969-G/1969-G.STEP which is licensed under...

I created an exact replica, as precise as possible, of the Front plate of the Ultimaker 2 for my ongoing project. I'm sharing this here so others can easily access it too. ...It's likely printable, but it would require a large 3D printer to produce.

This adapter spacer frame is essential if you want to fit the Chinese Ultimaker 2+ feeder to the Ultimaker 2, as some stepper shafts are too long on certain Ultimaker 2 models. Instead of cutting the shaft, which can be a bad idea, use this adapter...

These 4 brackets for the Ultimaker 2 and 2+ fit to the mainboard rev. 2.1.4 - 2.1.6 (without threaded sleeves M3) additionally a fan can be installed to cool the steper. For mounting without cooler, the opposite bracket can be mirrored so you get the...

This part can be added to the printhead of the Ultimaker 2 or Ultimaker 2+, including the Extended versions. The purpose of the part is to improve airflow from the tiny fan that cools the hotend parts. The part spaces the fan away from the heatsink...

This part can be added to the printhead of the Ultimaker 2 or Ultimaker 2+, including the Extended versions. The purpose of the part is to improve airflow from the tiny fan that cools the hotend parts. The part spaces the fan away from the...

I remixed this to fit the Foca 2.2 with the AVR six pin header installed. ...I increased the length and width by 2% to get a good fit.

... designed using the Customizer tool (http://www.thingiverse.com/apps/customizer/run?thing_id=151461). ...The specifications include hexagonal nuts with a size of 2.0, handles having a diameter of 25, and a hole delta value of 0.15 for adjustments.

... of http://www.thingiverse.com/thing:151461 was created using Customizer! ...Visit http://www.thingiverse.com/apps/customizer/run?thing_id=151461 for more details. For instructions, use handle diameter of 25mm, hole delta at 0.15 and hex size as 2.5.

To create a DIY printer modification, start by acquiring a 32x32 cm plate with a thickness of 2-3 mm made from acrylic glass. Place the necessary components onto the plate and drill holes in it for mounting purposes. When using "DoorHolder2" pieces,...

... on the mount's upper tab to enhance leveling. v1.2 boasts a slightly longer spindle, improving spool compatibility (thanks to gbo for the suggestion!) I didn't cut away as much material as I could, but since only one is needed, I opted for solidity.

Key enhancements to the initial design include: - Version 2, featuring the white components depicted in images, now skillfully captures and releases filament without drawing it back. - The absence of glue is a notable improvement due to the...

(2) The distance from the bottom face of the Fan-Duct to the build-plate is slightly low. At the outer edges of the build-plate - where the clamps are - the Fan-Duct collides with the clamps at the first layers. I currently use it only for smaller...

Ultimaker 2 X-Y Slider Block LM8U.

Ultimaker 2 um2 Spooler 76mm Holder

A custom enclosure was crafted specifically for the screen that accompanies the Lerdge 32 bit controller, allowing seamless integration with an Ultimaker 2 clone. The designed casing is broad enough to cover standard cutouts found on the typical...

The Ultimaker Open Source Hardware project, available at ultimaker.com, focuses on creating transparent and accessible technology for 3D printing enthusiasts worldwide.

這是混和E3D Ultimaker 2, 2+ Upgrade Conversion Kit與火山加熱鋁塊風扇組合 並且將限位開關集中在十字滑塊模組的設計

Storage Box for Ultimaker 2 Plus 3D Printer

.. ...Print Settings Printer Brand: Ultimaker Printer: Ultimaker 2 Rafts: Doesn't Matter Supports: No Resolution: 0.1-0.2 Infill: 20% Category: 3D Printer Accessories

The filament spool holder for the Ultimaker 2 measures a diameter of 25 millimeters and stands approximately 70 millimeters in length. ... Print Settings Printer Manufacturer: Ultimaker Printer Model: Ultimaker 2

Mount the Dropcam (Nest Cam) using an existing metal holder and screws. ... Print Settings: Printer Brand: Ultimaker Printer: Ultimaker 2 Raft: No Support: No