ultibots d300vs 3d models

I'm upgrading my XT-60 power supply panel with an RJ45 keystone module from MWU. I connected the panel to the motion control board using a short cat-6 cable and an inline keystone coupler, which was crimped together. ... It will look really sleek once I...

These STLs are for a case I printed for my D300 VS. It has several problems: 1) the front plexiglass is too close to the print bed to allow my Titan Aero to come all the way to the front of the bed 2) the PSU mount I printed doesn't leave enough...

All printers should operate without supports. For the "Flying Extruder," it's crucial to install all motors before attaching any extruder. The "Flying Extruder" is designed around the E3D Titan, but other extruders will likely work provided a pancake...

I discovered that my camera couldn't capture the initial layers of the print, so I created a custom mount to integrate additional lighting into the build plate area. ...To ensure constant illumination, I connected the lights directly to the Duet board's...

I've redesigned the original framework, lifting it off its foundation to create a sleeker appearance. The new design also shields the cables with protective covers and conceals the heated bed wires beneath, adding an extra layer of organization. To...

Simple Effector Delivers Top Performance Like Ultibot's D300. This compact effector features precision ball and cup joints, carefully engineered to accommodate an arm spacing of 55 mm. Designed specifically for a single E3D V6 hot end and the...

This project builds upon an initial electronic mount designed for the K250 from Ultibots. The original mount is well-designed but inserts itself too far into the K250 stand, leaving no room for other mounts to fit snugly alongside. A snapshot...

This is a custom-designed part blower for the Ultibots Micro Extruder, available at http://a360.co/2iuJnvE. The blower is made by combining half of a circular fan with M. Hackney's sublimelayer design, specifically the "Tusk" fan mount. Built-in...

I upgraded my d300vs/+ to a flex system with a 310 diameter. This mount is to be used instead of the original bed clamp and fsr mount, as it's all integrated. The idea is that the mounts will self align to the mag base. ...I am using the mag base...

I upgraded my D300VS/+ to a Flex System with a 310 diameter mount. This new mount replaces the original bed clamp and FSR mount, as it's fully integrated. The plan is for the mounts to self-align to the mag base. ...I'm using the mag base with the...

I thought it would be nice to have the spool holder sit higher and I wanted a lanyard mount for my wiring so I did both at one time. ...I like it.

... lid, and mount for a Meanwell EPP-400 3"x5" Small Form Factor PSU. ...It also features holes for sockets, switches, and an omron SSR. Print Settings Printer: Ultibots D300VS Rafts: No Supports: Yes Resolution: .2 Infill: 30% Category: 3D Printing

... dimensionally accurate and capable of bridging a circular gap with ease. ...This custom part is specifically used on my ultibots D300VS+, but it can also be utilized on any delta that employs the same effector plate and ball spacing configuration.

Consequently, I combined Ultibots' mounting element with carriage kit's belt clamps to secure fan duct at the rear side while maintaining belt positioning. ...This setup also appears compatible with potential upgrades like 40mm Supportless Directed...

To enhance stability, securely fasten the power cord into place using a cable tie. ...This precaution ensures that the connection remains intact and prevents damage due to unwanted slippage out of its assigned position within the equipment's housing.

I needed a tighter cone for my 16mm tube, one that would fit snugly onto spools with bigger diameters - up to 60mm - so I went ahead and did it myself.

I wanted slightly tighter cone for my 16 mm tube and wanted it to fit spools with larger diameter (up to 60m) so ended up doing this.

<p>I wanted slightly tighter cone for my 16 mm tube and wanted it to fit spools with larger diameter (up to 60m) so ended up doing this.</p> Category: 3D Printer Accessories

I loved the original, made it a bit thicker and made the cooler side holes wider for adjustments to better fit my layout.

Remix of Fan Tusk to Fit a Thingiverse Effector :). ... SOURCE HERE - Sublime Layers.

I thoroughly enjoyed the original design, so I decided to add some extra depth and make the ventilation slots even bigger to accommodate my unique setup perfectly.

... printer is particularly dimensionally accurate and is capable of bridging a circular gap. It's used on my ultibots D300VS+ but it can be used on any delta that uses the effector plate and has the same ball spacing. ... Category: 3D Printer Parts

This model can only be pulled off if your printer is particularly dimensionally accurate and is capable of bridging a circular gap. It's used on my ultibots D300VS+ but it can be used on any delta that uses the effector plate and has the same ball...

The holder is designed to mount onto an Ultibots D300VS, but could be mounted on a number of other printers. The bottom is vented so bits of plastic don't accumulate in the holder. Curad pads are available at Costco. Fusion 360 file included....

... Print Settings: Printer: Ultibot D300VS Rafts: No Supports: No Resolution: .4mm nozzle, .2mm layers Infill: 33% Notes: This print is straightforward. ...Three perimeters are recommended, and PLA works well, but any filament should also work fine.

This set includes modified micro extruders with a mount plate, spacing j-heads 20mm apart and compatible with Jonas Kuehling's X carriage standard. It is work in progress, yet to be printed, with no guarantees of functionality. Solidworks...

Print Settings: Printer: Ultibots D300VS Rafts: None Required Supports: Not Necessary Resolution: 0.2 mm Precision Infill: 25% for Optimal Performance Notes: PETG Works Well, but PLA or ABS Are Also Suitable Choices. ... Post-Printing Requirements: ...

Print Settings Printer: Ultibots D300VS Rafts: No Matter Supports: None Resolution: 200 microns Infill: 100% Notes: PETG was used to provide brackets with some flexibility, essential for crash resistance and screw holes. ...PLA may not be suitable due...

This is a replacement for the effector that works seamlessly with an E3D Aero, featuring a fan mount/duct as part of its design. It's specifically optimized to work with the E3D volcano, which boasts an 8mm taller heater block compared to standard...

... to 20mm V-Slot extrusion enables secure installation. ...On an Ultibot's D300VS printer, a 24V power supply is mounted using this method. ...The file ps_mount_tall.stl adds extra support by moving the power supply 16mm away from the rail for stability.