ultibots d300vs 3d models

This is a tension-adjustable V-Slot magball carriage (42mm spacing) derived from the Ultibots experimental carriage for the [D300VS](http://www.ultibots.com/) by Brad Norman found...

Also includes files I used to calibrate my D300VS+ after the build. Highly recommend the Hardened Hob Gear for the Titan Aero, I was having problems with the original stainless steel hob when i tried to push the printers speed limit. Like most...

Also includes files I used to calibrate my D300VS+ after the build. Highly recommend the Hardened Hob Gear for the Titan Aero, I was having problems with the original stainless steel hob when i tried to push the printers speed limit. Like most...

Additionally, I've included the files I used to calibrate my D300VS+ after completing the build. I highly recommend using a Hardened Hob Gear for the Titan Aero, as it solved my issues with the original stainless steel hob when trying to push the...

I'm using an E3D Hemera mount on my existing D300VS+ ball stud setup, just like the standard version. To print this model, you'll need to orient it upside down and add some support material. ...Don't even think about checking out my wiring, I only set...

With the extra spacers required for the Tricklaser arms on the D300VS+, it adds more leverage to the carriages which eventually warp over time. I have seen CF PETG and ToughResin carriages warp. Instead of a 3mm spacer on the eccentric, simply use a...

You can find more information about UltiBots at http://www.UltiBots.com. Be sure to check out our guide on NinjaFlex. For high-temperature filament, this design works with the E3D v6 Hotend Full Kit 3.00mm Direct and the E3D v6 Hotend Full Kit 1.75mm...

This is a duct designed specifically for the renowned Ultibots K250VS-BSE. It incorporates the original blower, ensuring optimal performance and efficiency. To achieve the best results, adjust the position of the duct so that it is as close as...

This is a customized airflow modification specifically designed for the D300VS, when paired with its standard micro extruder. It incorporates the stock 40mm x 40mm x 20mm blower fans without any need for rewiring adjustments. ...The design necessitates...

... as often when I get a little too vigorous with part removal. The files for the E3D hotend swap are directly from Ultibots; the micro extruder and other x-axis components. They will be tested once the hotend ships. ...they are untested as of now.

Simple adapter plate designed specifically for the D300VS+ printer, tailored to work seamlessly with the Dii Cooler. https://www.thingiverse.com/thing:1025471 The advantages of this adapter plate are numerous. Better cooling performance compared...

Why? Just for fun ;) Design: The scale factor is 0.6. Since the needed absolute offset is not scale able, some parts needed to be adjusted after scaling. ...That's why all 5 models are uploaded.

This is an adaptor to allow the Ultibots D300VS to use the OpenBuilds idler, which can be found at https://openbuildspartstore.com/smooth-idler-pulley-kit/

I was still struggling with achieving good bridges and overhangs at high printing speeds, so I opted for brute force cooling using two 5015 fans instead. The setup performs exceptionally well, but it can be too effective in some cases. To get the...

Still was having issues with getting good bridges and overhangs at fast printing speeds so I decided to just go with brute force cooling with two 5015 fans . Works like a champ, can work too well. Make sure your hot end has a sock and you...

The Ultibots 24V to 12V converter can be mounted on the MendelMax 1.5+, a kit and set of printed components that can be bought from their official website, www.ultibots.com.

This section connects the XT-60 connector to the lower frame of the UltiBots K250 (or BSE). ... Print Settings Printer Brand: RepRap Printer: Kossel 250 Rafts: No Supports: No Resolution: .25mm Infill: 15%+

This is a reworked version of Hayden Huntley's magnetic effector, tailored for seamless integration with the Ultibots Micro Extruder. ...Moreover, I've fine-tuned its configuration to utilize a PTFE tube as an intelligent filament guide system.

This is a remix of Hayden Huntley's magnetic effector for use with the Ultibots Micro Extruder. ... I also configured it to use a piece of ptfe tube as a filament guide.

The Ultibots K250 frame now accommodates a mounted PSU thanks to this bespoke mount designed specifically for that purpose. By reducing the height of the rubber pads slightly, it successfully fits snugly into place. ...A modified version is available...

This Upgraded Mount Is Designed Specifically for the K250 from Ultibots. A Major Drawback with the Original Mount is Its Proclivity to Pierce and Bind to the Stand, Leaving Minimal Room for Alternative Adapters. **User Manual** Important Notice:...

I received a fantastic kit from Ultibots (item 456659) that caught my attention right away! Unfortunately, I noticed some of the spools were having trouble fitting through the holder. To solve this issue, I took the initiative and designed a...

Connecting Your Voltmeter Panel to Your Printer ------------------------------------------ Locate the designated mounting points for your UltiBot's voltage display unit. Insert and fasten all included hardware as directed. Your connector board, now...

2015-03-18: Update V7: redesigned for optimal cable routing and upgraded connector mounting 2014-12-18: V4 Revamp: board rotation optimizes screw clearance, re-measured dimensions ensure accurate fit Reworking my initial electronic enclosure for the...

I designed this filament spool holder adapter for the Ultibot K250 V-Slot printer, available on Thingiverse at http://www.thingiverse.com/thing:456659. The regular sized Hatchbox spools that came with my printer worked great, but I wanted to use...

This is an expanded version of the D300VS wire mount, offering a neater and cleaner setup. It should work perfectly with any V-Slot type delta printer without issue. ... Additionally, one of these mounts has been rotated 90 degrees to prevent it from...

Instructions This was designed specifically with the Ultibots K250 in mind, so I'm unsure if the 300 has the same 2 sets of 2020 extrusion for the bottom frame or the correct height. After careful examination, I found that I only needed to use the...

Zesty Nimble E3D Magnetic Effector for Ultibots K250 Delta Printer with "Berd-Air" Style Cooling. Edit: I've got my Nimbles and have one up and running, so it's verified to work. I designed it using the Nimble documentation. Also note that there...

These are caps specifically designed for the corners of a D300VS delta printer. Using these caps allows one to adjust tower position without disassembling the belts or carriers. The parts are sized for commonly available 5/16" carriage bolts, as the...

Decided to optimize storage by attaching the Pi cam mount directly to my D300VS's existing bed clip assembly.